Search Documents

By A. C. Atenas

The majority of refineries that operate with traditional starting sheet technology ?starting sheet- uses a relatively low current density of 250 A/m2. Industrial tests at high current density with conventional technology were carried out in Refinery of Potrerillos, getting satisfactory results that are similar the results obtained with permanent cathode technology. The series of copper refining electrolyses electrolysis trials were carried out between 300 to 325 A/m2. Electrolysis conditions, in accordance with industrial practice, were kept constant in all sets of experiments and were as follows; 45 g/L Cu 2+, 210 g/L H2SO4, 62 °C, electrolyte circulation of 14-18 L/min. The same Dosing dosing of Additives additives used in permanent cathode technology was required in these tests. In general, only not importantminor operational modifications were necessary in comparison to normal practice in the Refinery to assure the good results. Different quality of starting sheet and anodes were examined. The test included starting sheets from smelter and laminated process. Results indicate that the charge physical quality of the electrodes and the control of the process during the two first days of operation are the keys to get the best results.

Jan 1, 2007

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By F. A. Auld

"During the period 1958-1980 seven deep shafts were sunk from the surface in the UK. From 1977 until 1989 sixteen deep shafts were sunk in the UK, all concrete lined. Subsequently from 1989 up to the present day no deep shafts have been sunk in the UK, a period of 30 years. Developments in the design and construction of deep shaft linings in the UK therefore were predominantly carried out throughout the period 1977–1989. This knowledge is recorded in several published papers by the author over that period which will be referred to in the paper. INTRODUCTION The paper includes a review of past precedent for the design of deep shaft concrete linings in the UK and sets out the principles for future designs, including the design load to be adopted and Factors of Safety (SFs) to be used in the design. Hydrostatic pressure increases with depth from the surface and therefore the concrete lining must increase in thickness and strength throughout its depth to resist the pressure. High strength concrete mixes were developed to enable economic linings to reach greater depths and these will be detailed. The ground conditions to sink through in the UK consist of predominantly competent (self-standing when excavated) rock, which can be water bearing, and hence a hydrostatic pressure resisting lining is required. The paper describes the construction measures needed to produce a dry shaft by way of pour length, joint detail, backwall grouting and joint sealing details. PAST PRECEDENT FOR UK DEEP SHAFT SINKING AND LINING Seven deep shafts were sunk from the surface in the UK from 1957–1977 over a 20-year period (Auld, 1987). These are listed in Table 1. Three shafts were for British Coal, two were for Cleveland Potash Ltd and two were for the Central Electricity Generating Board. The British Coal shafts were 5.486 m and 7.315 m internal diameter to depths of 550 m and 780 m, respectively. At 5.5 m internal diameter and a depth of 1150 m, the two Boulby Mine shafts for Cleveland Potash Ltd are currently the deepest shafts in the UK. The two Central Electricity Generating Board shafts of 5 m and 10 m internal diameter, to depths of 255 m and 440 m, respectively, were ventilation shafts for a pumped storage scheme. Six of the shafts were sunk by Thyssen (GB) Ltd and one by Cementation Mining Ltd."

Jan 1, 2019

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By E. Herrera Alarcón, L. Mariscal Samaniego

The Teniente Converter (wet charge type) was commissioned in august 1995 and was designed to smelt 744 tpd (metric tons per day) of dry copper concentrates. Its products are white metal (73% Cu) that is sent to the Peirce Smith converters, slag that is cleaned in Reverberatory Furnaces and the process gases that are sent to the Sulfuric Acid Plant. Since its start up, the Teniente Converter smelting capacity was increased 1.6 times, from 800 tpd to 1,280 tpd using 33% oxygen-enriched air, and reaching an operative availability of 97%. By the other hand its campaigns have reached a record duration of 530 days without hot patching tuyeres and a partial refractory lining repair in the last four campaigns. This paper describes the most relevant improvements, as well as the strategies that had been used to reach these achievements.

Jan 1, 2007

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By A. McLean, X. Men

"With high quality sulphide ores diminishing, nickel production from low-grade oxide ores becomes increasingly important and a major concern is the high sulphur level in the resultant ferro-alloy. So, desulphurization of the ferronickel becomes an important consideration. Red mud is a waste product of alumina industry and causes adverse effects on environment. In the present study, experiments were conducted to determine feasibility of using red mud as a major ingredient of refining fluxes for ferronickel desulphurization. In view of their influence on slag-metal separation, contact angle measurements between ferronickel alloy and molten slag made from red mud were also determined. INTRODUCTIONNickel is a very important metal that finds a variety of applications including consumer products, building, automotive and electronics. There are two kinds of ores containing nickel, namely oxide and sulphide ores. Anthony and Flett [1] reported that about 55% of the world’s nickel production originates from sulphide ores while the balance of new nickel is derived from oxide ores. However, oxide ores count for about 70% of the worldwide reserves. Apparently, oxide ores will play a significant role in the production of nickel in the future. Most of nickel produced using oxide ores is from pyrometallurgical processes namely ferronickel smelting or matte smelting. So, we can draw such a conclusion that using nickel oxide ores to produce ferronickel will become more and more important .Before used to make stainless steel or other materials, the ferronickel need pretreatment to remove impurities especially sulphur and phosphorus that will cause negative influence on the properties of steel product. Red mud is a by-product during alumina production. Usually, about 1 to 1.5 tons of red mud will be produced when we get 1 ton of alumina. About 90 million tones of red mud are produced every year in the world [2].Red mud is deemed as a toxic industrial waste which needs treatment before discharge because of alkalinity and chemical and mineralogical properties. Until now, the main means to deal with red mud are to store it in impoundments or dump it in the sea depending on local environment. Nowadays, how to recycle red mud has become a pretty hot topic around the world. The last 40 years have witnessed a lot of patent applications concerning the ways of red mud utilization. However, a little amount of red mud is consumed until now due to the limitations of recycling red mud."

Jan 1, 2012

By R. D. Brown

In his March 31, 1977 budget, Finance Minister Macdonald has attempted the delicate balancing act of stimulating the economy without reinforcing the inflationary pressures which Canada is continuing to experience. Several tax changes of benefit to the mining industry, as well as measures designed to encourage oil exploration in frontier areas, are among the budget proposals. Additional earned depletion of 66- 2 /3 %, which may be offset against income from any source, will be available on drilling costs in excess of $5 million incurred between March 31, 1977 and April 1, 1980 in connection with an exploratory well in Canada, including the continental shelf . Other changes include more favourable treatment of resource property dispositions, less restrictive rules r elating to "successor corporations" , increased capital-cost allowance on railway spur lines, the inclusion of certain production royalties in Canadian development expenses and the application of the lower "manufacturing and processing" tax rate to sulphur production. To encourage business capital spending, the 5% federal investment tax credit it to be extended an additional three years to mid 1980 and broadened to include spending on scientific research and development. The rate of credit will also be selectively increased on a regional basis, to 7.5 % in certain designated areas in Saskatchewan, Manitoba. Northern. Ontario and Quebec, and to 10% in the Atlantic provinces and the Gaspe.

Jan 1, 1977

By E. A. Rychkun

"For the last 700years of recorded economic history, man has been subjected to alternating inflationary and deflationary patterns. Through this period of time, a severe deflationary pattern has developed approximately every 55 years, creating 12recordable occurrences. Through the last two centuries, this severe deflationary phenomenon has come to be known as a depression. As these depressions have repeated themselves regularly, they are cyclic. This in turn leads to the question of whether the 13th cycle will also repeat itself in the form of a depression. As this cycle is now 51 years old, we must consider the possibility at about 1984.In analyzing a 700-year record of consumer prices in Southern England, the 55-year cycle appears to vary in shape and intensity. This varying phenomenon is due to the effect of longer cycles upon which each one ""rides "". Because each cycle effectively rides on the next largest, which in turn rides on the next largest and so on, the combined measured effect of all cycles together at any point in time is always unique. This means that anyone cycle can never repeat itself in an exact identical manner. The combined effect therefore is what we observe in the form of prices and, as cycles interact, variations in deflation are produced . The ""science"" of economics attempts to quantify and develop theory on situations which are never identical and hence can be conservatively classified as a useless predictive tool.This means that more unconventional approaches may be required to predict our economic future. In looking at previous depression cycles, it is possible to recognize similarities in human behaviour patterns and hence the resulting economic movements. These behaviour patterns create major events or influencing factors which set the scene for a major deflationary condition. The way in which these factors occur, however, is not predictable. As more and more of these similar events are identified in each cycle, we can increase our confidence on the probability of the last event occurring (a depression). By also unravelling the set of larger cycles, we can determine the potential combined effect at any point in the future.This paper presents a system of cycles ranging from 800 years to 3 years which appear to operate in our economic system. By so doing, a long-term projection into the next century can be made. Finally, the paper deals with the main controlling similarities within the depression cycle, to show that a comparison with our current cycle implies that a major deflationary collapse in the mid 1980's is virtualy inevitable."

Jan 1, 1980

By H. Gharahbagheri, S. Shafiei Zadeh, H. Hassan Nejad, Reza Roostaazad

In this paper, dissolution of vanadium from mining residue, in which vanadium is associated intimately with magnetite ore, was investigated via both bacterial ( aerobic and anaerobic) and fungal activity. Although bacterial activity was tangible, it could not reduce and dissolve vanadium in both aerobic and anaerobic experiments. However, in fungal leaching, after 30 days about 36.9% and 29.7% of vanadium was dissolved for a pulp density of 10 and 30 g/l, respectively. At the end, the concentration of metabolites usually produced by fungal activity was optimized and oxalic acid was chosen as the main agent for the leaching process.

Jan 1, 2014

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By Craig Dirk

Agenda Applications of ?GPS ?Drill Navigation ?Cycle time monitoring ?UDS / Boom Stress monitoring ?Payload systems ?Laser Surveying Future Applications

May 1, 2006

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005