Search Documents

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation on a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled -both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form as is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation ?On a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By G. G. Manekar

MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprise, under the Ministry of Steel, Government of India, produces about 1.1 million tonnes (T) of manganese ore annually from three opencast and seven underground mines. The underground operations are mining using an overhand cut and fill method. The orebody is too narrow for the use of larger equipment and the poor to fair rock mass quality limits the size of stable excavations. Prior to the 1990s underground support consisted primarily of timber square sets in tandem with timber chocks and props. As mine production requirements increased throughout the 1990s led to larger opening sizes and more modern support practices. Research was conducted on ground support design based on rock classification and empirical techniques for designing ground support. Based on the findings and field trials, the Company adopted full column cement grouted cable bolts for back support. Instrumented field trials, using extensometers and load cells on the cable support confirmed the support effectiveness. Stope design was based on two and three dimensional stress modeling which resulted in a significant increase in stope dimensions. The rock mechanics studies for safe stope design were carried out using numerical modeling tool in two and three dimensions for the analysis of stresses. Based on the findings, the safe stope geometry with new stoping parameters was introduced. The earlier stope length of 30 mtrs were changed to 60 mtrs with in situ rib pillar at the cross cuts and in situ post pillars to be left-out in the stope. This leads the formation of of panel comprising of three stopes, for production, supporting and filling. For mechanical handling of ROM in stopes Side Discharge Loaders (SDL) were introduced. The above changes have improved the face productivity from 2?3.5 T with manual operation and 9 T with SDL. The above rapid mining operations has improved the stope productivity but reduced the stope life from 6 to 3 years. For the improvement of the stope availability, further studies were conducted by numerical modeling of stress analysis. The related studies confirmed that with the existing supporting system and proper instrumentation, level interval could be increased up to 45 mtrs from the existing 30 mtrs at deeper levels. At present below 12th Level interval is 45 m at Balaghat Mine. For future mechanization program for introduction of Single Boomers, LPDT, Cutting Machines etc for the development headings rock mechanics studies are underway. The paper provides details of rock mechanics studies that were carried out to study efficacy of the cable bolt support, safe stoping parameters and increased level interval for the improvements in safety, production and productivity at Balaghat Mine.

Aug 1, 2013

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United 'States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By A. E. Aho

"The material presented in this paper will be subject to modification as new data become available, but it is presented in the hope that it will inspire more intensive mineral exploration and geologic studies of what appears to be one of Canada's richest mineral provinces. A metallogenic province 400 by 150 miles in extent, lying mostly northeast of Tintina trench, encompasses most of the base metal deposits of Yukon, as well as deposits of other metals. Its main features are northwesterly trending arcuate fold belts, with several orogenic axes, which include most of the metamorphosed rocks, granitic intrusives and mineralization; and which are modified by regional uplifts, northwest-striking fault trenches, and lesser transverse folding and faulting.The main base metal occurrences and their regional controls are summarized briefly. Most of the replacement-type deposits are localized in late Proterozoic to early Paleozoic rocks, particularly Lower Cambrian -probably because these are the most physically and chemically favourable hosts encountered in an appropriate temperature and pressure environment; perhaps because of early age of deposition. Most of the deposits also occur near heat sources or intrusives with associated structural uplift, which has, moreover, served to expose the older rocks. They also tend to occur near known or suspected regional fault trenches, such as Tintina, Macmillan and Hess, although this relationship may be fortuitous. In detail, they may be localized in fold axes, flat-lying beds or other appropriate structural traps. Vein-type deposits are fracture-controlled and localized by dilational localfties, the competence of wall rocks and ""damming"" effects.In the Anvil district, large stratiform iron-zinc-lead replacement deposits lie parallel to gently plunging flex-ures in phyllite in a zone parallel to the Tintina trench, along the southwest flank of the arch-like Anvil batholith. About 80 million tons of massive sulphide ore probably existed before erosion of the Faro orebody, the Vangorda deposit could have been of similar magnitude before erosion and much more tonnage probably remains to be discovered in the district. The Anvil deposits may differ from others found to date in Yukon, but resemble the Sullivan orebody of southeastern British Columbia in their large size, localization in essentially non-limy peptic to arena-ceous host rocks of Proterozoic or early Paleozoic age and proximity to the Rocky Mountain -Tintina trench sys-tem. These features suggest an origin from primordial subcrustal sources.More major ore deposits, not only of lead, zinc and copper but probably of other metals as well, will no doubt be found in similar environments in Yukon or Alaska. Thus, the base metal province of Yukon offers challenging opportunities for prospecting, development, field studies and basic research."

Jan 1, 1969

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By A. Moyano

The development of the traditional converting process performed in a PeirceSmith or Hoboken converter is limited by the investment magnitude associated to the fulfillment of the environmental regulations. Thus, the continuous converting process rather than a conceptual process alternative is becoming a necessity for a smelter facing limited converting capacity and/or lacking of fulfillment of the environmental regulation with its maximum converting capacity. The objective of this paper is to present the progress of the Codelco continuous converting process evaluated at pilot-scale level when converting solid mattes or white metal into blister copper. These tests allowed for gathering of relevant data to be considered for a new stage of evaluating the Codelco continuous converting at industrial-scale test. The pilot-scale tests were done in a Teniente Converter pilot scale unit at the Codelco Norte Smelter. The results of processing solid copper mattes (65-75% Cu) and producing low sulfur content blister copper with production of a constant S02 gas concentration, and the production of liquid slag with low copper solubility was achieved and is discussed in the present paper.

Jan 1, 2007

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By Arnold Blaisonneau, Théophile Guillon, Xavier Rachez, Sylvie Gentier

"L’étude présentée ici vise à étudier l’influence, lors de stimulation hydraulique de puits dans les réservoirs géothermiques de type Enhanced Geothermal System (EGS), du comportement mécanique des zones de failles recoupant le puits sur la réponse hydraulique du réseau de fractures 3D. Dans ce but, un modèle 3D, basé sur la méthode des éléments distincts et dans lequel les zones de failles recoupant le puits sont modélisées par des fractures numériques 2D, est mis en oeuvre. Les modélisations présentées ici visent à caractériser l’influence du comportement mécanique (type de comportement, hétérogénéité) sur la cinétique de la stimulation hydraulique, ainsi que sur son effet spatial autour du puits. INTRODUCTIONPour le développement de l’exploitation géothermique de type Enhanced Geothermal System (EGS), la phase de stimulation conditionne grandement le succés du projet ; en effet, elle a pour objectif d’augmenter l’injectivité et la productivité des puits et doit permettre d’assurer la connexion entre les puits d’injection et de production garantissant ainsi la viabilité technique et économique de l’échangeur. Pour le site EGS de Soultz-sous-Forêts (France), parmi différentes techniques de stimulation, la stimulation hydraulique a été utilisée à cette fin en provoquant une augmentation irréversible de la perméabilité autour des puits. Dans ce type de réservoirs fracturés, le but des stimulations hydrauliques est de réactiver, plus spécifiquement en cisaillement, des structures hydrauliques pré-existantes (fractures, zones de failles etc.) dans le socle cristallin. La compréhension des phénomènes physiques durant la stimulation hydraulique est cruciale pour optimiser cette technologie et pour contrôler/limiter les risques associés (viabilité technique et économique des puits, sismicité induite etc.). C’est notamment le cas pour la relation entre le comportement mécanique des structures stimulées et les conséquences sur le comportement hydraulique dans un contexte tectonique spécifique."

Jan 1, 2015

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By Patricia J. Dillon

Established in 1997, Prospectors and Developers Association of Canada Mining Matters (PDACMM) is a registered charitable organization dedicated to providing Earth Science education to grade school students. Through the development and distribution of educational programs and materials, PDACMM informs students of Canada?s geology and mineral resources as well as promoting awareness of the importance of rocks, minerals, metals and the mining industry. PDACMM also co-ordinates with other charitable organizations and government agencies to provide support or to work in tandem with them and reach as many young people as possible. Although PDACMM became a charitable organization in 1997, it actually has its? roots in 1994 when the Grade 7 program Mining Matters/Une Mine de Renseignments was developed to help teachers bring geology and mining into the classroom. Over 2100 of these resource kits were distributed to teachers across Ontario during the period 1995 to 1998. This unit won national recognition when it received the prestigious Partnership Focus award from the Conference Board of Canada for ?promoting science literacy for the world of work?. Due to the phenomenal success of these kits, a Grade 4 kit entitled Deeper and Deeper/Aller au Fond Des Choses was developed in 1998 in response to the opportunity provided by the new Ontario curriculum released at that time. Over 2600 of these kits were distributed throughout Ontario and there is a substantial waiting list of teachers hoping PDACMM will be able to raise enough money for another print run.

May 1, 2002

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010