Search Documents

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35'W, latitude 49°25'N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By Su-Ping Peng

Three dimensional (3D) seismic exploration has been carried out since the 1980s in the mining district of China, where it has been playing an indispensable role in the high yield and efficiency of coal mining. Unlike oil exploration, this technique uses high density seismic acquisition technology. In recent years, it has focused on wide azimuth 3D seismic acquisition. Evaluation of geometry moved away from depending on folds, azimuth and offset, toward being based upon a focus-ray beam. Conventionally, coalfield 3D seismic interpretation focused on time domain and was based on kinematics information, which is only suitable for less complex geological conditions. To achieve high-resolution processing for the complex topography and structure in coalfields, data processing shifted from poststack to prestack. The means to improve the accuracy of interpretation for complex geological conditions are 1) integration of multiple attributes and multiple disciplines, 2) combination of seismic and geological data, and 3) comprehensive combination of time domain and depth domain data. With the demand for lithological exploration, high-resolution data processing must also take into account the requirements of preserving amplitude in seismic data. Seismic attributes technology, seismic inversion technology, and dynamic tracking interpretation are key techniques in 3D seismic exploration. They greatly improve interpretation accuracy, produce better results in the goaf space description of the coal-bearing strata and coal seam structure, and effectively reduce exploration costs under complicated geological conditions. Therefore, these techniques will be the primary means employed in the future to deal with coalfield complex structure and lithological exploration.

Aug 1, 2013

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By D. A. Bordin, C. J. Newman, R. J. St. Eloi

"The requirements for a metallurgical acid plant treating smelter gases are both unique and demanding in terms of sulphur dioxide treatment and emission control. Since start up in 1981, the copper smelter at the Kidd Creek Division of Falconbridge Limited has undergone several major expansions. The expansion and modification of the acid plant has been an integral part of this process. Both production demands and government regulations dictate that this metallurgical acid plant be unique in terms of operating flexibility. The variable capacity to treat a wide range of sulphur dioxide concentrations, and the operating flexibility to control emissions are the topics of this paper.INTRODUCTIONThe Kidd Creek Division of Falconbridge Limitied is a base metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April, 1964. Mining operations began in 1966 with a 9000 tonne per day concentrator coming on stream in November of that year. In April 1972, a 108 000 tonne per year zinc plant was commissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 tonnes of ore per day . To expand zinc production, the world's second installation of the Cominco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 125 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No.3 tankhouse technology for the copper refinery.The smelter, which uses the Mitsubishi Continuous Smelting Process for the continuous production of blister copper from concentrate, went on line in June 1981. It has been expanded from its original capacity of 60 000 tonnes to 100 000 tonnes per year of copper.From the very early design stages for the metallurgical complex, the company had adopted a policy of constructing and operating modern plants which would meet existing and anticipated environmental standards. With this in mind, the decision was made to utilize the proven technology of fixing sulphur dioxide emissions, in the form of sulphuric acid. A 636 tonne per day single absorption contact acid plant was built to serve the zinc plant in 1972. In 1981, an 883 tonne per day double absorption contact plant was built to serve the needs of the copper smelter. The copper smelter acid plant has since been expanded to a design capacity of 1692 tonnes per day and it is the main focus of this paper."

Jan 1, 1989

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

To create a successful growth oriented diamond company that succeeds in the practical business of mining and selling rough diamonds, and which pursues an aggressive exploration strategy to seek and develop worldclass diamond mining opportunities in a market that has become increasingly under-supplied.

May 1, 2008

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By Z. D. Hora

The major fluorite producer in British Columbia was the Rock Candy Mine, inactive since 1942. Other deposits of economic interest include the Rexspar deposit, in which fluorite is associated with uranium and rare earth mineralization, and the Eaglet and Liard River occurrences. THE former Rock Candy fluorite mine, located 26 km north of Grand Forks, is the only major past producer of fluorite in British Columbia. The deposit was in production from 1918 to 1929 and again in 1942; total output was about 36,000 tonnes with average grade between 22 and 32 per cent CaF2. The fluorite body occupies a steeply-dipping vein structure, approximately 175 m long and up to 12 m wide, in porphyritic syenite. The chief vein-filling minerals are quartz and fluorite with local small len ses of barite. Fluorite content decreases with depth and the deposit becomes silicified. The Rexspar (or Birch Island) fluorite deposit is located 130 km north of Kamloops. The deposit is complex with rare earth elements and high uranium values, but !1uorite mineralization forms an independent zone adjacent to the uranium orebodies. Fluorite is present as fine-grained impregnations and as breccia cement in strongly schistose or brecciated alkali feld spar porphyry. Reported reserves are 1,088,000 tonnes of 22 per cent CaF2 or 450,000 tonnes of 29 per cent CaF2. 268 Another potential deposit of fluorite is Eaglet, situated on the north side of Quesnel Lake. Fluorite occurs as a stock work with scattered veins and irregular lenses up to 20 centimetres wide and as impregnations in altered Proterozoic Kaza Group feld spathic gneiss over an area of 1,500 metres by 500 metres. To date (1983) approximately $2 million have been spent on the exploration of this property and reserves of 18.8 mimon tonnes grading 11.59 per cent CaF2 have been outlined . A group of significant occurrences is known from north of Liard River Hot Springs Park , where fluorite occurs in small zones up to 17 m thick along the interface between Middle Devonian Dunedin Formation limestone and Middle Devonian to Mississippian Besa River Formation argillite. Fluorite, associated with witherite, barytocalcite and barite, is present as replacement bodies, breccia fillings and minor veins.

Jan 1, 1984

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time over 140 million tons of waste and low grade material has been placed on the mine waste dumps. Laboratory and in-situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electrowinning plant. The plant, which was commissioned in October, 1984 was designed to process 3,000 usgpm of dilute copper solution to produce 5,000 tons per year of high quality cathode copper.This paper deals with the start up and initial year of operation of Gibraltar's SX-EW plant. The three areas: leaching solvent extraction and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to die Gibraltar operation.THE LEACHING CIRCUITThe mines waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dump. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and disolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the suphides and solublization of the copper into the acid solution.For the bacterial action to occur the dumps must be at or near the ideal pH of 1.9 - 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate. See figure 1.The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start up in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate. See figure 2."

Jan 1, 1988

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By W. A. Roliff

The renewed interest of the past few years in the Appalachian and Michigan oil provinces has not, as yet, created any marked increase in activity in Southwestern Ontario. During 1960 development drilling in-creased somewhat over 1959, but exploratory drilling decreased slightly. More attention was devoted to the deeper horizons, but lake drilling de-creased considerably. Oil production reached a new peak and gas production increased slightly. During 1960 an interesting oil and gas discovery was made in the Cambrian and gas discoveries six miles off-shore in the eastern part of Lake Erie were made in the Clinton-Cataract zone of the Silurian. This paper reviews activities during 1960, summarizes the discoveries made to-date and the pertinent exploration data relating to the prospects of the region and discusses some of the economic aspects of exploration and development. D URING the last few years there has •been a marked renewal of interest in the old petroleum

Jan 1, 1961

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015