Search Documents

By M. G. Manzone

Approximately two-thirds of the annual 210,000 tons at copper refined by AMAX Inc. at the United States Metals Refining Company in Carteret, New Jersey, comes from a wide variety of copper scrap ranging from low-grade smelter scrap to wirebar-grade material. The equipment and methods used to effect such large-scale metal recycling in an urban area and the measures taken to collect and recover metal values from smelter and refinery byproducts while protecting the environment from pollution are described and discussed.

Jan 1, 1977

By M. E. Grimes

"The future of the uranium industry in Canada during the next twenty years will be very dependent on political and social issues on a world scale. Technology, as such, will tend to be of lesser importance. Nonetheless, some technical changes can be anticipated.This paper deals with milling of uranium ore, leaving further processing and nuclear power production to specialists in these fields. An attempt has been made to look at uranium production technology in Canada in relation to that in other countries, and to draw interference regarding future changes that seem probable in the Canadian context. In particular, recent advances in mill equipment are considered.The chemistry of uranium and its relatively low concentration in most ores has been responsible for a completely hydrometallurgical approach to mill processing, and this should continue. In spite of little commercial success to date, pre-concentration of lower grade ores will be researched further in order that these ores can compete with higher grade deposits in Canada.The discovery of the relatively high-grade ores of the Athabasksa region will undoubtedly influence choice of mill processes and equipment. The potential effect on innovations is discussed"

Jan 1, 1986

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By Ann Bigué

Outline of Presentation 1. Impacts and Benefits Agreements Defined 2. Elements that determine the content of an IBA: ? the nature of the project ? the identity of Aboriginal communities affected by the project ? the legal environment 3. Content of Impacts and Benefits Agreements Impacts and Benefits Agreements Defined Have emerged in response to effects of major mining projects located on or close to Aboriginal lands and close to Aboriginal communities Are negotiated between the mining project proponent and one or more Aboriginal groups May include government May be known under other names

May 1, 2004

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By George Brien, O&apos

The history of the lighting of mine workings dates back to the early part of the 18th century, when small candles known as tallow dips, were used. These were set or held in a lump of wet clay. When looking for gas the flame of. the candle was reduced to a mere glimmer by surrounding the wick below the flame with clay. The candle was then very cautiously raised from the floor toward the roof, the observer screening the brighter portion of the flame with his hand and watching for the first appearance of the pale blue cap above the flame, even at that time, known to indicate the presence of gas. When this appeared the candle was lowered quietly and its flame extinguished before attempting to drive out the gas. A very common and dangerous practice adopted at that time was to get rid of the gas by firing it. This was done by a person selected for his nerve rather than for his caution. Dressed in a? suit of dampened sackcloth or leather, this man well termed a "fireman", would lie prone on the floor of the roadway and light the gas above him by raising his candle fastened to the end of a long stick. If he survived, which was not always the case, he would withdraw promptly to fresh air after the flame had passed over him.

Jan 1, 1924

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016