Search Documents

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By E. Hardwick, K. C. Sole, Y. Jurrius

"The Luilu cobalt plant at Kolwezi, Democratic Republic of Congo, has been operating since the late 1950s, using a conventional precipitation flowsheet for removal of impurities from the cobalt process stream. Most impurities are, however, incompletely removed using this technology. Copper and zinc, both of which quantitatively deposit at the cathode in the cobalt electrowinning process, are two of the main impurities contaminating the cobalt metal product. Ion exchange offers a modern approach to removing these impurities from the cobalt advance electrolyte.Following a laboratory testwork programme to identify a suitable ion-exchange system, an on-site pilot-plant trial, treating 1500 to 3000 L/d of electrolyte, was operated for a period of six weeks to optimise the operating conditions and to determine full-scale design criteria. Copper removal was carried out using a fixed-bed lead-polish configuration with the Lanxess iminodiacetic acid resin, TP 207. Zinc removal was subsequently carried out in a similar configuration using the Lanxess aminophosphonic acid resin, TP 260. The optimised system proved capable of removing both copper and zinc from 20 to 30 mg/L to <1 mg/L from plant electrolyte containing ~20 g/L Co. Selective elution allows co-loaded cobalt to be returned to the main circuit and value to be obtained for the copper impurity. The process shows operational and economic advantages over the traditional flowsheet. Full-scale implementation of the developed process is in progress and some design considerations are discussed."

Jan 1, 2014

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By C. Edwards

"The processes for rare earth (RE) extraction include the decomposition of RE ore concentrate minerals, and the concurrent or subsequent leaching of the rare earth elements (REEs) from the decomposed minerals. Ore beneficiation concentrate can be decomposed by, for example, acid roasting, caustic cracking, and chlorination. The REEs can be selectively extracted. The nature of the REE extraction process depends on the concentrate mineralogy and the targeted products. Based on the experience of the Saskatchewan Research Council (SRC) in RE processing, this paper reviews REE extraction from the major RE minerals, including bastnaesite, monazite, xenotime, ion-adsorption clay, allanite, cerite, and eudialyte. An update on the development of RE extraction processes is also provided.INTRODUCTIONRE processing usually involves two operation stages, physical processing and chemical processing. Physical processing, also known as ore beneficiation, separates the RE minerals from gangue minerals to produce an RE mineral concentrate. Chemical processing, which includes extraction and separation processes, converts the RE mineral concentrate to an RE compound which is either an end product or an intermediate product for the subsequent production of individual REEs or other compounds. The RE extraction process uses one or more reagents to decompose the RE minerals and to leach the REEs into solution. The RE separation process uses solvent extraction, ion-exchange, or chemical precipitation to produce either rare earth oxides (REOs) or individual REEs. The authors have previously reviewed RE ore beneficiation processes (Zhang & Edwards, 2012). This paper focuses on extraction processes for a variety of RE minerals. Table 1 gives the chemical compositions of the RE minerals mentioned in this paper. The varieties of RE extraction methods use many different reagents. These reagents are mainly inorganic acids, alkalis, salts, and chlorine gas. The commonly used acids include sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3). Sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) are the most common alkalis. Salts include ammonium sulphate ((NH4)2SO4), ammonium chloride (NH4Cl), and sodium chloride (NaCl). HCl is normally used to extract RE from silicate ore minerals such as allanite and gadolinite. The alkalis and H2SO4 are mainly used to leach REs from phosphate ores minerals like monazite and xenotime. The carbonate ore RE minerals such as bastnaesite can be treated using either acids or alkalis. HNO3 is mainly used to leach eudialyte and apatite. The extraction of REs from ionadsorption clay deposits uses salt solutions. Chlorine gas (Cl2) is exclusively used in the RE chlorination process which can be used to treat any RE minerals."

Jan 1, 2012

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By E. W. Lucht

THE term "high pressure", as used in industry today, is applied rather loosely. Generally, it refers to pressures that are higher than those encountered in most industrial processes although no definite limits are normally stated. For the purpose of this talk I should like to set rather arbitrary limits to the term "high pressure", and in ab-solute figures this would be the range from 1000 psi to perhaps 40,000 or 50,000 p.s.i. The scope of high pressure technology is very broad, and it would take more time than we have avail-able here today to cover fully even one aspect of the field. Therefore, I should like to discuss just some of the techniques used and problems en-countered in high pressure operations. Research work into the high pressure region dates back about 150 years, but it was not until 1910 that the first commercial application of high pressure technology was made in the production of ammonia.

Jan 1, 1962

By D. P. Goodall

THE development of the oil and gas resources of Western Canada is not, as many suppose, a new industry. For more than half a century an intensive search for these valuable products of nature extended from near the western edge of the Precambrian Shield to the Pacific coast, and from the International boundary north to the Arctic circle. The chief centre of interest to the oil prospector has, however, always lain in that region lying east of the first range of the Rocky mountains and confined largely within the boundaries of the Province of Alberta. Although there are many geological problems yet to be worked out in this Province, the oil-well driller has helped in no small way in determining sub-surface conditions and distribution of rock formations. The chief geological conditions as they affect the drilling of wells are generally re-cognized, and for this purpose the Province may be partitioned into three main divisions: first, the disturbed belt or foothills region extending along the eastern edge of the Rocky mountains; second, the Alberta geosyncline, a broad trough lying to the east of and parallel to the disturbed belt and from which the formations rise eastward to level off and form, third, the plains ? ? region, extending over the rest of the Province. A relatively small area in the northeastern part of the Province is underlain with Precambrian rocks and may be excluded from this classification, as it is of no interest to the oil prospector. The foothills, or disturbed belt, has presented the greatest difficulty to drilling, though it has produced the largest yield of oil within the Province to date. Within the foothills belt, the rock formations consist largely of hard shales interspersed with layers of abrasive sandstones, which wear out drilling bits at an alarming rate. The strata, in most flaces, dip steeply and are cut by numerous thrust faults. Although some o the faults have great displacements, their presence may easily be overlooked or the extent of the fault misinterpreted. Many a prospect well has been located on what appeared to be a suitable geological structure only to find, after drilling through a normal succession of rocks for 4,000 feet or more, that the drill had passed through a major fault plane to a younger formation than that in which drilling was started. Only a repetition of formations already drilled could be expected at greater depths.

Jan 1, 1942

By J. J. Denny

IN November, 1932, an investigation of silicosis was undertaken at the Mcintyre Porcupine mine, Schumacher, Ont., after a discussion of the p"roblem with Sir Frederick Banting and his staff. As a result, it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions. At that time 50 guinea pigs were placed in the crusher house tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation (1) led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill. The CO, combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid, and alkaline solutions on the solubility of siliceous materials. Gye and Purdy (2) were the first to point out that the chemical reaction, and not the physical presence of siliceous material, was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings (3), who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response, while the 10-12 micron particles produced only a foreign-body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter.

Jan 1, 1937

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By Robert L. Tremblay

Dans le but de voir si une région comme la Gaspésie, qui a subi la derniere glaciation , se prête avantageusement à la méthode de prospection alluvionnaire, environ 800 concentrés de minéraux lourds furent prélevés dans les districts électoraux de Matane et de Gaspé-Nord. Les différentes phases minérales présentes dans les concentrés ont été examinées à la loupe binoculaire. Afin de mieux valoriser ce type d&apos;inforrnat ion, nous avons été arnenés à expérimenter et à mettre en oeuvre des techniques multivariables adaptées au traltement d&apos;une information semi-quantitative en utilisant le principe d&apos;un codage logique préalable. La structuration des résultats de la Gaspésie a conduit à l&apos;élaboration de cartes de synthèse qui constituent un support nécessaire à l&apos;interprétatlon des répartitions plus ponctuelles des minéraux "utiles" sur le plan de la recherche minière.

Jan 1, 1978

By Chi Zhang, Junyi Wu

"The use of permanent stainless steel cathodes for electrorefining and electrowinning of cathode copper had been introduced to the market long time ago and now is a well-accepted technology worldwide. During the last decades, the Chinese copper refinery industry had been growing rapidly and many large scaled production plants had been built. In the modern refineries, permanent stainless steel cathodes are introduced and used instead of traditional starter sheets. The most common steel grade used is austenitic stainless steel S31603 (316L/1.4404), while both S30403 (304L/1.4404) and N08904 (904L/1.4539) have been used depending on the actual working conditions, especially with regarding corrosion environment. While 316L permanent cathode functions well in many plants, different kind of problems, such corrosion and deformation, have been reported. There is therefore an increased need for more suitable material. New stainless steels, such as duplex stainless steels, with better properties have been tried and introduced into the application of permanent stainless steel cathode with satisfied results. The article introduces first the Chinese copper refinery industry and properties of duplex stainless steel in general, and then describes the development of using permanent duplex stainless steel cathode, including the actual working conditions, production of cathode sheets as well as the experiences of application in details. After more than one year’s usage, the advantages of permanent duplex stainless steel cathodes are clear seen.INTRODUCTIONChina has become a major player in the international copper market, accounting for around 40 percent of global refined copper demand. Despite the slowdown of the Chinese economy, the consumption of copper products will still increase, but with a medium and/or low growth which will be the new situation for the coming years. The average growth rate is expected to be around 5 percent per annual. In the coming Five-Year plan for National Economic and Social Development a number of initiatives will be finalized which will require massive amounts of copper. In 2015, the expected consumption of copper products will be over 9 million metric tons. The main driver of the consumption is the electric power industry which accounts nearly the half of the total consumption; followed by cooling application with 15% and transportation with nearly 10%, see figure 1."

Jan 1, 2016

By R. R. Bassermann

THE property of Howey Gold Mines, Limited is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National Railway line. The mine has been a continuous producer since April, 1930, and at present is hoisting 1,350 tons of ore per day. The shaft consists of three compartments (see Figure 1, sketch B). Hoisting is done by two skips in balance, one of which is interchangeable with a cage. Sinking had been carried out at three different periods. From the surface to the 550-foot level, the sets had been spaced at seven-foot intervals, from the 550-to the 1,060-foot level at six feet, and from the 1,060-to the 1,500-foot level at five feet. During the five years of operation, the shaft had become so badly worn, due to spill from the tipples and, to a certain extent, from the loading pockets, that re-timbering was considered necessary. It should be explained that no crushing is done underground because of the ad verse effect this would have on the efficiency of the sorting. The grizzly rail clearance above the ore pockets is fourteen inches and consequently the ore hoisted is extremely coarse. More than average spill from the loading pockets and tipples under such conditions is inevitable, and it is debatable whether underground crushing with consequent increased sorting costs would not be justified. The cost of complete re-timbering according to standard practice would have been prohibitive both directly and indirectly: A lengthy shut-down of the shaft, with the consequent disorganization of the staff and workmen, could not be considered. Accordingly, it became necessary to devise some method of repair that could be carried to completion in a very limited period of time. The shaft timber for the first 250 feet was not in need of repair. From the 250-foot to the 1,060-foot level the wall plates, posts, and blocking were in good condition. These had been protected by a one-inch plank lining put in at various periods during the past three years without interfering with hoisting operations. The end plates and dividers, however, could not be protected in this manner because of the lack of skip clearance. It was decided that, if the dividers in this section could be replaced, the shaft would be as satisfactory as if completely re-timbered. Several factors had to be taken into consideration in deciding on a suit-able method of repair. In the first place, the tipple plates had to be re-designed. To complete the job in a reasonable time, not only had work to be done on the tipple, but simultaneously from several points in the shaft itself. Since all power cables, pipe lines, etc., were in the manway compartment of the shaft, this compartment had to be left undisturbed.

Jan 1, 1935

By Jonathan Peck, Carl Hendricks

"Global Positioning Satellite (GPS) based positioning and navigation systems have been recently developed and implemented by AQUILA Mining Systems Ltd. on blast hole drills and electric cable shovels in Canadian open pit coal and iron ore mines. These systems enable the location of the drill bit or the shovel tracks to be accurately determined in three dimensions. The position of the drill or shovel is displayed to the operator via a real-time, Moving Map Display (MMD) on an LCD-VGA screen. The MMD allows the operator to accurately navigate the drill from blast hole to blast hole or maintain a desired shovel grade or face position, with respect to displayed bench features. The maps for the MMD are downloaded from the mine office via laptop or radio link as required or as mining plans change.To obtain reliable, accurate and real-time3D positions of mobile mining equipment, proven GPS technology has to be utilized. The GPS components need to operate reliably under the severe environmental conditions that exist on board mobile mining equipment. In addition, they have to contend with varying pit geometry’s and satellite configurations, with little or no performance degradation. These issues were initially examined in December1993 during a feasibility project between AQUILA and Gregg River Resources Ltd., in relation to implementing GPS systems on blast-hole drills.To achieve certain design objectives, AQUILA Mining Systems Ltd. has developed navigation systems for cable shovels and blast-hole drills based around off-the-shelf, high precision GPS components. These systems utilize the AQUILA Advanced Monitoring Platform (AMP), to display graphically, via the MMD, shovel grade and drill position to the operator to within ±12 inches of design coordinates. Production prototypes have been installed on a Marion 301 cable shovel and a Bucyrus-Erie49-R Series III drill at the Fording River Mine in August, 1995, at the Wabush Mine on a Bucyrus Erie 190-B shovel in June, 1995, and on a GD120 drill at Gregg River Resources Ltd. in January, 1996. All these systems have undergone field trials to test system components and functionality’s under actual production conditions. This paper will discuss these GPS-based positioning and navigation systems in subsequent sections."

Jan 1, 1997

By Robert B. Parsons

"The last edition of Tax Notes expressed concern about two proposed tax changes in Finance Minister Paul Martin&apos;s 1995 budget that could have detrimental effects on Canada&apos;s mining industry. This month, Tax Notes expands on these concerns. This article is based on a paper that the author presented at ClM &apos;95 in HalifaxIntroductionOn a global basis, there are more investment opportunities in the mining industry today than at any other time in history. Countries in Central and South America, Eastern Europe, the CIS, Central Asia, and Asia are competing aggressively to attract investment to all sectors of their domestic mining industries. Today, the demand for investment dollars exceeds the amount of dollars that are available for investment in mining. It is not surprising, then, that the established mineral producing nations are witnessing a decline in spending on exploration and development on their home turf, and an increase in spending in developing countries. In the context of a developed country such as Canada, there are two manifestations of the problem of declining investment: (I) Foreign investors are allocating more of their capital budgets to new opportunities in developing countries; and (2) Canadian juniors and seniors are spending proportionately more abroad. This shift in global spending patterns is the source of some concern for the future of Canada&apos;s mining industry, particularly because it is widely believed that the current rate of discovery of ore reserves in this country is too low to replenish depleting reserves.""Government bashing"" has always been a popular pastime in Canada. Invariably, this pastime has focussed, at !east in part, on taxation. In view of the intense competition that Canada faces on the global mining scene, it is important that the role of taxation in the decision-making process be kept in perspective. This paper seeks to put the role of taxation into perspective."

Jan 1, 1995

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By W. A. Parks

Stone that may be applied to purposes of construction is available in nearly all the inhabited parts of Canada, the most important exception being the prairie region, but, even here, the deficiency is overcome in many parts by a wealth of glacial field-stones. In many parts of the country, also, the accessible stone is of a quality so poor that brick is more generally used. There is a great difference, however, between stone that &apos;may be used&apos; and stone suitable for buildings of a monumental type or even for &apos;trimmings&apos; on the better class of dwelling in the cities and towns. It is in the latter sense that the expression &apos;building stone&apos; is commonly used. Thus restricted the term includes varieties of sandstone, limestone, and granite, using the latter word in the custom of the quarryman, not only for the true granite of the geologist but for many other igneous rocks as well. Building stone of high quality grades imperceptibly into stone suitable for monuments, particularly in the case of the granites. The present review will deal with building and monumental stone in this restricted sense and will omit marble, although that material has been used to some extent for building. For instance, the Great West block in Winnipeg is built of marble from British Columbia.

Jan 1, 1925

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen&apos;s budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada&apos;s mining industry which is involved in mining the country&apos;s vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget &apos;has serious implications."

Jan 1, 1981

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997