Search Documents

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick's Law in 1947, through to today's models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

By Michel L. Bilodeau, Brian W. Mackenzie, Dallas W. Davis

"The paper formulates an evaluation procedure for examining the effects of location on the economics of developing mineral deposits. This methodology is applied to assess locational aspects of Nova Scotia's competitive position f or mine development relative to other Canadian regions and provinces. The appraisal concerns two representative mine development opportunities, a medium-size open-pit tungsten deposit, and a small underground gold deposit. The influence of regional economic conditions is initially assessed. Then, the consequences of taxation are isolated. Finally, the combined impact of regional and taxation conditions is examined. SettingThe economic potential of mining may be assessed in a number of ways. One approach, increasingly used for both corporate planning and government policy purposes, is to evaluate the competitive position of an actual or potential mineral producer in the international marketplace relative to other suppliers.Such examinations of competitive position vary from cost league comparisons of breakeven costs for operating mines, through the assessment of medium-term costs associated with developing new mine capacity, to long-term evaluations of the economics of mineral supply from the start of exploration. The complexity of the analysis increase s with the scope and timeframe of interest. Many factors are involved. One component of competitive position is the quality of the mineral resources available. Other key factors include existing technology, wage and salary rates, labour productivity, the cost of capital, infra structure requirements, distances from sources of materials supply an d to mineral markets, management attributes, organizational efficiency, government mineral policies (particularly taxation), and inflation and exchange rates. The paper fits within this competitive position framework.The variable economic conditions which exist within Canada have a direct bearing on the viability of mine development and, thereby, on mineral exploration potential. The paper examines locational aspects of Nova Scotia 's competitive position."

Jan 1, 1986

By Bruno Lafrance

Abstract - Quartz veins at the Mufferaw gold prospect and Komis gold deposit, northern Saskatchewan, are examples of oblique-extension veins that crystallized in shear and tensile fractures, which propagated and then opened oblique to their walls during a single continuous deformation event. The Mufferaw gold prospect consists of an interlinked mesh of conjugate shear fractures, tensile fractures, and veins. Oblique-extension veins crystallized in conjugate shear fractures, which opened during dilation of intersecting tensile fractures under the same far-field stress system. At the Komis gold mine, tensile and dextral shear fractures cut across granodiorite dikes. The tensile fractures formed perpendicular to the dike margins during stress transfer from the less-competent country rocks to the more-competent dikes. During extension of the dikes oblique to the bulk extension direction in the country rocks, the tensile fractures were reactivated as sinistral shear fractures. The reactivated tensile fractures and dextral shear fractures opened oblique to their walls, parallel to the bulk extension direction, and were sealed by the deposition of oblique-extension veins during the same deformation event.

Jan 1, 2004

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By W. Dietzel

Fracture mechanics based techniques are used to gain insight into the phenomenon of stress corrosion cracking (SCC) and to develop guidance for avoiding or controlling SCC. From constant extension rate experiments under rising load or rising displacement conditions the susceptibility of high strength steels, aluminum, magnesium and titanium alloys to SCC and hydrogen embrittlement can be assessed. Such tests on pre-cracked specimens are also well suited for studying the mechanisms leading to SCC by employing appropriate models for the degradation of metallic materials which take into account the uptake of atomic hydrogen from the corrosive environment. Measurements of crack growth resistance curves using the crack tip opening displacement as fracture parameter can be compared with simulated R-curves obtained from modeling of the mechanism of hydrogen embrittlement. The materials investigated are a high strength steel and a magnesium alloy both exposed to environmental conditions which fostered the uptake of hydrogen.

Jan 1, 2010

By P. Cain, B. Martens

"Grande Cache Coal (GCC), an investor-owned Alberta company, is in the final stages of the regulatory process leading to the resumption of coal mining in the Smoky River Coal Field of Alberta. Although many opportunities for low-cost, high-yield mining remained on the property, GCC opted for a long-term production plan that ensures stability for the local economy, sustainable use of the resources in the area, environmental responsibility and a satisfactory return for its investors.GCC entered the Alberta coal approval process in late 2000 with a public disclosure document. In October 2001, GCC formally submitted an application for mining approval and an environmental impact assessment (EIA) to the government and the public. The application covered the proposed Grande Cache Coal project, which includes the No. 7 underground mine, No. 8 surface mine and coal processing operations. The EIA provided a comprehensive investigation of environmental sensitivities in the project area, matched with environmental protection programs. The project is based on commencement of operations in late 2002. GCC’s plans are founded on a commitment to sustainable development and has framed this commitment in the context of a long-range mine development plan that will sustain the community of Grande Cache over the next 25 years. The Grande Cache coalfields offer extensive coal reserves and opportunities, for both surface and underground mining. Combining highly productive U.S.-style room and- pillar underground mining methods and conventional truck-and-shovel open pit mining, GCC’s approach to sustainable development encompasses community involvement and reclamation of mine sites to productive land uses after mining."

Jan 1, 2002

By J. S. Redpath

There appears to a definite trend toward the hoisting of greater tonnages from greater depths. There is every indication that this trend will continue and we feel that improvements in the design, fabrication and installation of mine guides will be of significant importance in the future. The present state of the art in mine-shaft guide systems is reviewed and the parameters required for improvement are derived in this paper. Finally, a proposal is made for a new steel guide system which meets the parameters and is economical to fabricate and install.

Jan 1, 1977

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By K. Turgeon, D. Larivière, L. Whitty-Léveillé, J. -F. Boulanger, C. Bazin

"The processing of ore containing rare earth elements leads to the production of an impure solution of these elements. The separation of the rare earths from the impurities and the production of individual elements is usually carried out by solvent extraction. The effectiveness of the extraction conditions and of the reagents is generally tested in the laboratory. This paper deals with the processing of results from solvent extraction laboratory tests planned to generate data redundancy. A method is proposed to take advantage of the data redundancy by accounting for the pH variation during the extraction. The parallel processing of several tests also allows estimating the equilibrium constants for the extraction. The proposed method produces equilibrium constants that are more reproducible than values estimated using conventional approaches. The method is illustrated with solvent extraction tests conducted on synthetic solutions of rare earth elements.INTRODUCTIONThe processing of ores containing rare earth elements (REE) usually includes the production of a concentrate of the minerals carrying the REE. These minerals, for instance monazite and bastnäsite, contain the 14 elements from La to Lu plus yttrium and scandium. As an example monazite has the general formula of (La,Ce,Pr,Nd,Sm,Eu,Gd,Tb,Dy…Lu)PO4 with a typical lanthanum content of 20-26%, cerium content of 40-50%, praseodymium of 4-6%, neodymium of 16 to 20%, and decreasing concentrations of heavier elements (Gupta & Krishnamurthy, 2005). During the processing of a REE mineral, it is generally not possible to isolate and separate a single REE from all the rest. The mineral molecules need to be broken (usually via a heat treatment followed by leaching with a base and/or an acid) to produce an aqueous solution of the REE of the ore. After purification of the solution, the REE can be precipitated as a bulk concentrate and sold to a refinery that separates the REE into particular groups of REE such as the light versus heavy REE or into individual elements such as lanthanum, neodymium, or europium oxides to yield value-added products."

Jan 1, 2016

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By Hyung Sup Choi

The preparation of high-purity zirconyl compounds was studied in order to develop an economical process for obtaining pure zirconium via the caustic fritting of zircon sand. The direct dissolution of caustic frits with concentrated hydrochloric or nitric acid at 80c. followed by the addition of a small amount of acidified gelatin, gave high-purity zirconyl chloride or nitrate. The addition of a small amount of gelatin caused a mutual flocculation between colloidal silica and gelatin. The precipitation of this silica floc markedly lowered the content of silica in the product. The silica content of the compounds (or solution) so produced, generally less than 100 ppm., was sufficiently low for tributyl phosphate extraction for nitrate solutions. It was found that the degree of purification de-pends not only on the procedures employed but also on the nature of the frit itself. Silica was more effectively eliminated from the fritted product produced at higher temperatures, and less silica was present in the com-pound prepared from the frit produced in a shorter heating time. In order to ascertain the nature of the

Jan 1, 1965

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

By L. S. Rivett, U. M. Oko

The Strathcona mine, with a large new underground operation and concentrator, was recently brought into\ production by Falconbridge Nickel Mines Ltd. The tailings disposal and water utilization problems at Strathcona are described in this paper, with sections devoted to the Moose Lake watershed system, tailing impounds, the construction of dams and the operation of the Moose Lake neutralization plant for the elimination of acidity, including the equipment used.

Jan 1, 1971

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978