Search Documents

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By Tassos Grammatikopoulos, Sarah Prout, William Mercer, C. Gunning

"The Nechalacho rare metal deposit is located in NWT, Canada. Avalon Rare Metals Inc. is now evaluating processing techniques for recovery of REE to be used in the industry. QEMSCANTM analysis coupled with whole rock, REE, Zr and Nb, and electron microprobe analyses were utilized to identify and quantify the mineralogy of the deposit, and define the REE distribution among minerals. QEMSCANTM mineralogy was performed on fifty intact drill samples using EXPLOMINTM that provided textural information for the mineralization; crushed samples were used to determine the variability of the ore and define REE domains, and composite samples to determine the liberation and association of the REE minerals. The sample matrix predominantly consists of biotite, feldspars, quartz, muscovite/clays, minor chlorite and amphibole, magnetite and hematite and carbonates. REE include in decreasing order of abundance allanite (3.6%), monazite (1.5%), synchysite (0.9%), columbite (0.9%), fergusonite (0.6%), bastnaesite (0.4%), and zircon 11.0%. The majority of the HREE are carried by fergusonite and zircon, and the LREE by monazite, allanite, synchysite and bastnaesite. QEMSCANTM mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data have been implemented in defining the mineralogy of the ore body, support metallurgical test work, predict recoveries and grades, and finally calculate reserves of the deposit.INTRODUCTIONAvalon is in the unique position of owning and developing one of the world’s largest rare earth deposits in the Northwest Territories of Canada.The term Rare Earth Elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties. REE are not particularly rare and have a similar abundance in the earth’s crust to nickel, tin or tungsten. Unlike these better known metals however, the rare earths have little tendency to become concentrated into commercial ore deposits. When they do become concentrated, deposits of REEs usually display enrichment in one of two groups. The most commonly occurring deposits of REEs contain a sub-group of elements referred to as the “light rare earth elements” (LREEs), which include lanthanum, cerium, praseodymium, neodymium, and samarium. Less commonly, deposits of REEs contain the much more valuable sub-group of elements referred to as the “heavy rare earth elements” (HREEs), which include europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. Yttrium and scandium most commonly occur in association with this second HREE sub-group. Generally, LREEs are produced from the mineral bastnaesite, and the HREEs have been produced from the minerals xenotime and monazite. LREEs continue to be produced from bastnaesite, however in the 1980s, China started production of HREEs from unique laterite clay deposits. China now produces approximately 95% of the world’s rare earths."

Jan 1, 2011

By É. Roberge, S. Makni, G. Gagnon, F. Lavoie, A. Faucher

"Feed particle size is an important variable for the primary grinding mill operation. Several commercial vision systems have proven to successfully measure online many types of ores and are used for automatic control. However, due to limitations associated with segmentation algorithms, these systems fail to provide good measurements when the feed is composed of a specific bimodal particle size distribution: very big rocks and a large amount of fine particles. This is typically the case for crushed iron ore. This paper presents a technique to overcome the limitations of existing vision systems by using 3D cameras and appropriate processing methods. It provides online particle size distribution indicators and bulk volume flow rate measurement. It is designed to be very cost-effective, robust, precise, easy to install and to maintain. The 3D system was validated in two iron ore processing plants and the results clearly show that it can be used to optimize primary grinding mill operation where 2D segmentation vision systems fail.INTRODUCTIONFragmentation measurement using digital image processing has successfully been applied in mining and mineral processing operations. Several maintenance and operating applications are already deployed in the industry: Measurement of rock fragmentation after blasting (Maerz, 1999; Palangio, 1999) (Pragyan, 2012) Truck inventory (Palangio, 2005) Monitoring of crusher mantle wear Automatic control of crushers and SAG mills (Bouajila, 2000) (Bartolacci, 2001)Commercial technologies like WipFrag (Maerz, 1999), VisioRock and others proved to be very efficient to precisely measure the particle size distribution of many types of materials. These products are mainly composed of a camera, a lighting system and an image processing system based on a segmentation algorithm. By controlling adequately the lighting conditions and with periodic maintenance on the segmentation algorithm calibration parameters, it is almost always possible to achieve reliable measurements.However, the segmentation algorithm is not adequate when the particle size distribution contains big rocks and a large amount of fine particles. In this case, the area containing the fine particles is accounted as a big rock while big rocks get segmented as multiple smaller sized particles, leading globally to a wrong measurement. This situation prevails for crushed iron ore and coke, among other materials. Figure 1 shows a picture of a material which is typically very difficult to process through segmentation techniques."

Jan 1, 2015

By E. W. Johnson

"The title of my paper is ""I 'Wonder Where The Yellow Went"". As you can readily guess, it is not related to an old-fashioned ""Pepsodent"" sales pitch! Rather, it concerns a situation which arises all too frequently in some gold milling operations, namely when actual ounces of gold production do not come up to estimated or projected ounces. The boss man scratches his head and wonders where the missing gold has gone and how it has disappeared. The problem, if one exists, is amplified if one forgets that an estimate is just that - an estimate - and not a hard fact - even though the numbers are produced by computers. And yet, from the point of view of engineering; financial and production planning and security; it is most desirable to tie together all data relating to production estimates, losses and actual production.In the course of this paper reference will be made to the term ""variance psychology"", to a few of the physical properties of gold and to the nature of its occurrence in Canadian ores, in relation to the topic under consideration. Activities which have a bearing on production estimates will be reviewed. These include: weighing, sampling, assaying, estimating residual losses and, in cyanide plants, gold precipitate production. Mention will be made of apparent, unaccounted for and unknown losses. In conclusion, I shall draw from personal experience and relate three examples of ""Where the Yellow Went''."

Jan 1, 1986

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By P. Oyanader

"In 2001, the Catholic University of Chile undertook a maintenance benchmarking study of six open pit copper mines having mill capacities varying between 18,000 t/d and 156,000 t/d, and collectively responsible for 58% of Chilean copper production. This paper describes the methodology used to conduct the study, as well as the overall results. Key performance indices were selected to measure the effectiveness, efficiency, and development of the maintenance process. Using a balanced scorecard philosophy, these indicators were divided into client satisfaction, financial, internal process, and learning and growth indices.Maintenance was found, on average, to be responsible for 44% of mine production costs. Percentage planned maintenance of equipment fleets was found to be low by world standards, averaging 35%, 56%, and 44%, respectively, for blasthole drill, shovel, and haul truck fleets. Fleet availabilities were found to be significantly influenced by the percentage of planned maintenance achieved, while maintenance cost per equipment was found to decrease non-linearly with increases in percentage planned maintenance. Investment in technical training (including planned maintenance practice) was found to be low by global standards. The paper concludes that fleet availability and maintenance costs in Chilean open pit operations could be considerably improved by improving and/or developing maintenance planning standards, and investing in training personnel in planned maintenance techniques"

Jan 1, 2005

By Scott Martin

This paper will discuss the challenges currently facing the mining industry. By sharing experiences gained in the CIM Leading in Mining Course, I will highlight what’s working, what’s not, what are the challenges, what are the concerns, what are the opportunities, what needs to happen. Specifically, I will discuss what is currently happening with leadership and leadership development in members’ own organizations, what skill sets are important to develop in different hierarchical groups and how comprehensive leadership courses like the leading in Mining course can help improve leadership within individuals and the industry. Leadership development is a process not an event.

Jan 1, 2014

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By B. Hart, J. Marois

"Scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM–EDX), and Time of flight secondary ion mass spectroscopy (TOF-SIMS)were used to analyze pyrochlore grains from Niobec froth flotation plant. Samples from the mill feed, pyrochlore rougher feed, pyrochlore rougher concentrate, and tail were analyzed in order to identify a potential relationship between pyrochlore matrix composition and selective separation. SEM-EDX analyses indicate that pyrochlore grains with high Fe content appear to be less recoverable than those with a lower Fe content and that the flotation response is related to matrix Fe rather than Fe occurring as inclusions. TOF-SIMS was used to analyse the surface of high Fe and low Fe pyrochlore, in order to identify a potential relationship between pyrochlore matrix composition and the related effect on cationic collector adsorption (tallow diamine). Surface analyses of pyrochlore from a conditioning test show that species indicative of the collector favour the surface of Fe poor pyrochlore relative to the Fe rich variety. The results from the conditioning test illustrate a negative relationship between collector loading and the presence of Fe and related oxidation species. This study identifies the link between pyrochlore matrix Fe content and, the presence of surface oxidation products, to collector loading. Poor Fe rich pyrochlore recovery noted in the Niobec froth flotation plant may be partially explained by this mechanism.INTRODUCTIONPyrochlore, the most abundant niobium containing mineral (Perrault and Manker, 1981) is economically recovered in Brazil, China, and Canada (Niobec) (Kouptsidis et al., 2008). Since 1974 Niobec has been extracting niobium from the St-Honorécarbonatite deposit. Niobec is the only operating Nb extraction facility in North American and one of the three major world producers of ferroniobium (Dufresne and Goyette, 2004; Belzile, 2009).Flotation is the preferred and most cost-effective method for pyrochlore recovery (Burks, 1958; Shapolov and Polkin, 1958; Zakharov et al., 1967; Razvozzhaev and Nikiforov, 1972; Bogdanov et al., 1973; Abeidu, 1974; Raby and Desrochers, 1975; Wilson, 1979; Biss and Nadeau, 1982; Biss, 1985). With the aim of optimising the flotation process for the Niobec ore, numerous experiments were performed on the influence of surfactants and type of water to optimise pyrochlore recovery and grade during flotation (Gomez et al., 1987; Rao et al., 1988; Dufresne and Goyette, 2004; Belzile, 2009)."

Jan 1, 2013

By H. G. Rushton, A. S. Romaniuk

"The opening chapter of this volume, by A. Ignatieff, places in perspective Canada's coal resource base as part of the world scene. This chapter will focus on the Canadian scene.Units of measurement in this report are in the International System of Units (SI) as approved for official use by the Canadian Standards Association and Metric Commission Canada. These units have been adopted by the Mining Association of Canada and the Coal Association of Canada. To assist with the shift to metric units these two associations have published ""Metric Practice Guide for the Canadian Mining and Metallurgical Industries"", 1978(1J, Appendix ""A"" lists some useful conversion factors along with SI prefixes. The last official assessment of Canada's coal resources and reserves was done by the Department of Energy, Mines and Resources and presented in Report ER 79-9 ""Coal Resources and Reserves of Canada"", published in December 1979 and authored by H.U. Bielenstein, L.P. Chrismas, B.A. Latour and T.E. Tibbetts(2). The Geological Survey of Canada has a continuing project concerned with coal resource assessment as does CANMET, whose concern is with coal reserve assessment and coal quality. As well, Alberta's Energy Resources Conservation Board (ERCB) has a continuing assessment program for coal in Alberta and publishes an annual reserves report, the current issue of which is cited as reference No. (3). The difference in resource and reserve terminology as used by EMR and ERCB has a major effect on derived tonnages for Alberta. This difference will be discussed later. In 1982 the Department of Energy, Mines and Resources produced a map titled ""Canada-Coal""<4J which outlines coalfields and illustrates coal import and export movements for the years 1981and1980. A copy of this map is contained in the map pocket of this publication. Two other resource assessment reports are noteworthy, the first is ""Coal Resources of Southern Saskatchewan: A Model for Evaluation Methodology"", by J.A. Irvine, S.H. Whitaker and P.L. Broughton<SJ which is one of the major outputs of a joint federal-government study of southern Saskatchewan's lignite deposits. (Another output from this same study' is the Geological Survey of Canada's SASCO file, a computer processable file holding borehole and coal quality data.) The second is ""Deep Coal Resources of the Interior Plains, Estimated from Petroleum Borehole Data"", by G.D. Williams and M.C. Murphy(6) which identifies coal resources from nearly 4,000 petroleum exploration boreholes distributed uniformly over an area spanning Manitoba, Saskatchewan, Alberta and British Columbia."

Jan 1, 1985

By F. Vasilikou

Commercial deployment of Carbon Capture Utilization and Storage (CCUS) requires field testing of a scale that can stress the geologic reservoirs. One such reservoir of interest consists of unminable coal seams that exhibit favorable characteristics and depositional environments and lower pressure and temperature than other, deeper, reservoirs. Such conditions can reduce compression costs while utilizing the action of adsorption that offers a more effective carbon dioxide (CO2) bonding than free storage or solution. To ensure the success of such tests, a number of parameters should be accurately determined, such as the seam geometry and stratigraphy, coal porosity and permeability parameters as well as optimum injection conditions. In essence the CO2 injection model should be calibrated for the reservoir characteristics using all available data. History matching calibrations are based on gas and water production from existing wells prior to injection. This paper will present reservoir models that were developed for a pilot--scale 907 tonnes (1000 tons) CO2 injection test that was performed in 2009 through one legacy coalbed methane production well in Russell County, Virginia, USA. The model incorporates a number of individual coal seams about 0.3 m (1ft) in thickness located at depths ranging from 300 to 700 m (1,000 to 2,200 feet). Model calibration was performed through history matching to prior production data, and subsequently the model was utilized to develop different injection scenarios. The developed model was used after injection to calculate CO2 plume distribution patterns that were monitored at the injection test. The paper will present model data and assumptions with a special emphasis on the effect of hydraulic fractures and the skin factor to the coalbed methane (CBM) production model.

Aug 1, 2013

By Kathryn L. Neale, Derek L. Mulligan, Robin E. Goad, Norman A. Duke, A. Hamid Mumin, W. John Camier

"Abstract - The NICO and Sue-Dianne deposits are being explored and delineated by Fortune Minerals Limited in the Mazenod Lake District of the Northwest Territories, using an Olympic Dam model. The deposits were discovered in the south part of the Great Bear magmatic zone (GBMZ) within the Proterozoic, Bear Structural Province of the Canadian Shield. They are the only known significant Canadian examples of Proterozoic iron oxide-hosted polymetallic deposits. Worldwide, this class includes such deposits as Olympic Dam and Ernest Henry in Australia, Kiruna-Aitik in Sweden, and Salobo in Brazil. Their considerable size, up to 2 billion tonnes, and polymetallic ore assemblages make them highly attractive targets for exploration. Common characteristics of this class include their Early to Middle Proterozoic cratonic settings with extensional rifting evolving from collisional tectonics. Deposits typically occur along major structural lineaments within the aureoles of a distinctive suite of anorogenic potassium-rich "A-type" granite intrusions. Although hosted by diverse lithologies, deposits of this class are characterized by a number of other diagnostic regional- and deposit-scale features, which may be recognized in reconnaissance- and propertyscale geological and geophysical surveys.The southern GBMZ in Canada has several characteristics (age, tectonic setting, geology and geophysical attributes) similar to those of the Olympic Dam deposit and its other significant global analogues. Airborne and ground geophysical surveys carried out in the GBMZ identified coincident potassium, uranium, magnetic, resistivity, chargeability, and gravity anomalies centered over the NICO deposit. The nearby Sue-Dianne deposit is characterized by coincident uranium, potassium, magnetic, resistivity and chargeability anomalies. Both deposits occur within a regional, northweststriking, arcuate trend of volcanic and sedimentary rocks characterized by significant positive Bouguer-gravity and magnetic responses and are believed to represent a major basement discontinuity. The NICO anomalies are at the intersection of this regional trend with a major transverse fault through Lou Lake. Regional and local geophysical data indicate the presence of significant concentrations of iron oxide within a broad area of intense potassium metasomatism. Geological mapping identified cobalt, gold, bismuth, and copper mineralization in biotite-magnetite-amphibole-sulfiderich ironstone and schist. This mineralization is localized within altered wackes of the Snare Group, which are unconformably overlain by potassium feldspar- (±hematite ±magnetite) altered rhyolite of the Faber Group. The Sue-Dianne deposit is a hematite-magnetite-Fe-silicate-cemented diatreme complex enriched in copper, silver, gold, and uranium within a broad zone of potassium, iron, quartz, and epidote metasomatism. The diatreme is located at the intersection of two major faults at the north end of the basement discontinuity and is hosted in rhyodacite ignimbrite marginal to the Faber Lake rapakivi-granite pluton. At both deposits, diatreme- and maar-facies iron oxide-cemented breccia straddle the regional metasedimentary-volcanic unconformity, suggesting that mineralization formed in a near-surface environment synchronous with the onset of volcanism."

Jan 1, 2000

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017