Search Documents

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By T Mizuta, H Satoh, M Ogasawara, M Miyata, M Fukuyama

The Miocene Chichibu granitoids associated with the Chichibu skarn deposit are divided into North Body, South Body and Daikoku altered stock. Orebodies of the Chichibu skarn deposit are mainly distributed in the north-western part of the North Body and Daikoku altered stock. The North Body consists of magnetite-series granitoids ranging from tonalite to granodiorite and to monzogranite from the margins to the centre of the intrusion. The South Body consists of tonalite and granodiorite, and most of these rocks are also classified as magnetite-series granitoids. The Daikoku altered stock consists of a quartz diorite porphyry. The SiO2 contents of the granitic rocks of the North Body and South Body range from 61.6 to 70.7 wt per cent. During magmatic differentiation, Cu, As and Zn contents in fresh granitic rocks of the North Body and South Body increase with SiO2 content up to 63 wt per cent SiO2, and then progressively decrease with increasing SiO2 contents as SiO2 exceeds 65 wt per cent. Estimated pressure for the emplacement of the granitoids is about 0.5 kbars. Cathodoluminescence studies on quartz from those granitic rocks show that vapour rich two-phase fluid inclusions tend to occur in the core of quartz crystals, while halite-bearing poly-phase fluid inclusions occur in the margins of quartz crystals. The distribution of fluid inclusions suggests that fluid composition changed from low to high salinities during the growth of magmatic quartz crystals. Texture showing quartz crystals with an oval shape enclosed by radial aggregates of a mixture of fine-grained quartz, plagioclase and K-feldspar composing the groundmass of the monzogranite also suggests a pressure decrease during solidification of North Body. These findings show that high salinity fluids were present during magmatic differentiation and that Fe-Cu-Pb-Zn-Au-Ag skarn mineralisation of the Chichibu deposit was possibly associated with these high salinity fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By P Commander

Western Australia is a major exporter of minerals, which places significant economic and environmental responsibility on Government and the stateÆs mining industry. Moving into the 21st century, mineral production in Western Australia is $14 billion accounting for 50 per cent of the stateÆs export income. There are over 60 large-scale mining operations distributed throughout the arid regions of the state (less than 300 mm/year rainfall). There are four key mineral provinces in arid Western Australia including the Pilbara (iron ore), Murchison (gold), Northern and Southern Goldfields (gold and nickel). These provinces have significant differences, particularly in respect to groundwater demand from mining and mineral processing, aquifer systems that are utilised, and approaches to groundwater management. The arid nature of the stateÆs interior and subsequent lack of surface water resources has required substantial groundwater resource development by the mining industry. A variety of aquifers have been explored and utilised ranging from shallow alluvium and calcrete, discrete fractured zones in bedrock, concealed palaeochannels and inland sedimentary basins. Groundwater usage by the mining industry is about 150 GL/year with most abstraction related to mine dewatering, mineral processing and dust suppression. Groundwater abstraction in Western Australia is regulated by the Water and Rivers Commission. In the Goldfields, the depletion of brackish (>2000 mg/L) and saline groundwater from storage is permissible, as mining is considered the beneficial use for groundwater which may be as much as 200 000 mg/L. In contrast, the low salinity groundwater of the Murchison and Pilbara is allocated on a sustainable basis. The role of monitoring and ongoing aquifer reassessment is crucial in water management, in evaluating the condition and performance of stressed aquifer systems. Mining operations face a variety of water resource issues ranging from insufficient availability for processing to excessive mine dewatering. These issues also change as a mine operation proceeds through its development, commonly starting with a deficiency and moving into surplus as deeper pits require more dewatering. Operating mines have to contend with three main issues: water supply, wastewater disposal and contamination of local water resources. In contrast, post closure issues are related to aquifer recovery or re-establishment of groundwater equilibrium, development of pit lakes in mine voids and isolation of waste products and associated seepage or run-off.

Jan 1, 2003

By W T. Pate, A V. Potapov, J K. Lichter

Even though flotation is one of the most important unit operations of mineral processing, accurate modelling of this process for plant performance prediction has remained elusive. In the last four to five years dramatic changes have occurred in our ability to make credible model based predictions. This paper briefly traces the history of flotation modelling from simple (lumped pulp-froth) æchemical kinetic analogueÆ models for single cells to more detailed multi-phase, multi-component population balance models for banks of cells. It then focuses on recent developments in physics-based modelling tools. This includes current efforts to model the forces of attachment and detachment at the individual event level as well as multi-event levels in individual cells and circuits. Two examples of these tools are presented. The first is DEM modelling of the mechanics of motion of bubbles in froths. The second is population balance modelling of the dynamics of flotation circuits describing how they are influenced by upstream processes (such as crushing and grinding) as well as internal process variables (such as aeration, agitation and reagent addition). Applications of each of these tools are discussed.

Jan 1, 2005

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

By Binns MJ

Gold/silver orebodies of the Golden Plateau deposit, Cracow, Central Queensland, are currently being exploited by the Cracow Mining Venture. A geostatistical block model has been prepared to assist with long term mine planning. The Golden Plateau orebody, of inferred epithermal origin, is a multiply brecciated, silicified fault complex containing irregular, tabular and pipe- like oreshoots. Historically the lode has been stoped and open cut over a strike length of 750 metres at widths of up to 15 metres and to a depth of 250 metres. The Golden Plateau mine produced 1.55 million tonnes of ore at an average grade of 12 g/t Au and 13.5 g/t Ag over a 42 year period. In the preparation of the reserve model much reliance has been placed on recent diamond and reverse circulation drilling (71 holes in total). However a significant volume of data has been derived from historical level assays and underground diamond drilling. Over 3,000 level assays and 50 underground drill holes contributed to the database. Similar lognormal populations were observed for 1 metre composite grades from each major drilling campaign once corrections were made for core loss. Cumulative frequency plots revealed only one outlier which was cut to the population line. The population statistics from the historical level assays showed a significant difference from those derived from the drill hole composites. Level assay populations were cut to local drill hole populations before incorporation into the ore reserve model. The resulting data has yielded interpretable variograms, the parameters of which have been applied to the preparation of a kriged block model of the deposit.

Jan 1, 1987

By C Kocsis, G Baiden, Y Bissiri

CANMET-MMSL and Penguin Automation Systems Inc have been exploring how process simulation and ventilation modelling software, when combined, can be used to optimise hard-rock/metal mine ventilation systems. In combination, it is anticipated that this methodology will facilitate the exploration of mine design options that affect ventilation requirements and ultimately cost. Such integrated mine design could limit, and possibly reverse, the drivers that under current practices would generally dictate increased ventilation, power consumption, cost and greenhouse gas emissions. It is believed that the mining industry needs such process models to develop better business cases. For example, the implementation of optimised ventilation systems will undoubtedly require significant investment and mines are often reluctant to try such conservational measures unless they can be proven cost-effective. In general, Canadian hard-rock mines know their ventilation systems are providing too much air and consuming power unnecessarily. This is because their systems are designed to provide maximum production flexibility, based upon peak demand, which may be at some future time, and operated continuously at that level regardless of actual need. Simplistic analyses have shown electrical energy savings can range from 30 per cent through to 90 per cent (Hardcastle, Gangal and Leung, 1998). These savings depend upon such factors as the intensity and continuity of the production schedule as opposed to non-productive time. Where these savings occur is also important, if limited to either the primary or auxiliary ventilation systems, they could be negligible in a mineÆs total energy consumption. The problem these mines face is determining what level of ventilation is required in real-time and then the relative benefits. Such parameters as varying electricity costs, heating fuel options, different design criteria and their complex inter-relationship can effect the selection of an optimal system, depending on whether energy, environment or cost is the prime driver. The use of process simulators in underground mining is in its infancy; to date they have been used to show the benefits over the life of a mine under different mining methods, such as a comparison of tele-remote mining from surface against conventional manned operation (Baiden, 2000). This ongoing development advances the use of such simulators into a new and potentially important area, namely modelling the life-cycle ventilation requirements of a mine. This paper shows how such a life-cycle analysis as opposed to peak demand can provide the basis for optimising the design of ventilation systems and their control.

Jan 1, 2005

Some important mineral fields are referred to in discussing the formation of placer deposits in Australia. Testing methods include boring hand, with percussion rigs; with auger and pit digging drills; and l by vibro drilling. Sampling errors are minimized by the use of correct techniques and equipment for boring, sampling, and sample dressing, A hypothetical set of data is used to demonstrate the final process of evaluation, and some relevant taxation provisions are discussed.

Jan 1, 1964

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By G Harbort, T Georgiev, M Phillips

Phu Bia Mining Ltd, a subsidiary of Pan Australian Resources Ltd owns and operates the Phu Kham copper concentrator located in the Xaysomboun District, Lao PeopleÆs Democratic Republic. Construction and commissioning of the 12 Mt/a copper concentrator and associated facilities was undertaken by Ausenco Ltd and handed over to Phu Bia Mining Ltd in April, 2008. The first copper concentrate was produced in April 2008 and the ship carrying the first shipment of copper concentrate set sail 27 July 2008. Nameplate mill throughput was reached in August, 2008 when 1 020 000 dmt of ore was treated in the milling and flotation circuit. The Cu-Au mineralisation is contained in skarn and stockwork mineralisation and is interpreted as a distal expression of a conventional porphyry copper-gold system. Copper mineralisation is principally in the form of chalcopyrite with lesser bornite. Gold occurs as small grains, typically associated with copper minerals. In the upper portions of the orebody, oxidation and water table movements have resulted in near surface leaching of the copper and below the leached zone, supergene enrichment resulted in chalcocite mineralisation. The circuit operates with a semi-autogenous grinding (SAG) û ball mill circuit, feeding a bank of OK200 rougher cells. Rougher concentrate is reground in an IsaMill prior to entering a cleaner circuit consisting of three stages of cleaning and one stage of cleaner scavenging. The concentrate typically assaying 24 per cent Cu and 6 - 7 g/t Au is hauled for over 1000 km across the border to the Port of Sriracha in Thailand, and stocked in sheds at the wharf from which it is shipped to various Asian smelters. This paper discusses the successful commissioning and ramp up to design tonnage and metallurgical performance. In addition, a program to optimise both the comminution and flotation circuit is detailed with reference to grinding efficiency, flotation residence time and size by size mineral recovery.

Jan 1, 2009

Mineral Sands - "An Industry for the Future"The mineral sands industry is matched only by the gold industry in relation to its current buoyancy. The strong demand for the various mineral sands products, creates a positive environment in which to review the technical and commercial factors affecting the future of this industry. This conference is clearly being held in the right place at the right time.My role today is to put forward a few ideas that may help Australia to assert its rightful role as a major downstream player in an industry which it has dominated for 25 years as a raw material supplier.

Jan 1, 1986

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By D La Rosa, A Jankovi, A Dance, W Valery

This paper presents the methodology for optimising blasting and comminution processes in terms of fragmentation developed by Metso Minerals Process Technology Asia-Pacific and South America (MMPT). The methodology is called process integration and optimisation (PIO) and involves a number of steps: benchmarking, rock characterisation, measurements, modelling/simulation of blasting and comminution processes and where required, material tracking. The measurements collected while at site are combined with rock characterisation and definition of ore domains to model the complete process chain. These data are used to develop site-specific models of blast fragmentation, crushing, grinding and flotation. This allows customised blast patterns to be developed that optimise both crushing and grinding performance. For each domain, blast designs are recommended to generate the optimal fragmentation size for downstream processes. The objective is to minimise the overall cost for the entire process and the changes often have a positive impact on the mining operation. Process constraints such as wall stability, ore dilution, muck pile characteristics, size of mining equipment, size and installed power of crushing and milling equipment and other process bottlenecks are considered in the blast designs. This methodology has allowed many operations around the world to significantly increase their production: generating typically five to 20 per cent higher concentrator throughput. A number of case studies will be discussed in this paper to describe the structured approach taken and demonstrate the benefits that are achievable. This paper will focus on the role of blasting in the optimisation of the entire mine to mill process chain and discuss elements of the PIO methodology: rock characterisation, fragmentation modelling and measurement, the relationship between fragmentation and mill throughput and material tracking.

Jan 1, 2007

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By J L. Merritt

Effective minesite water management requires that this issue be treated as a risk management exercise. The management process is generally far from simple and by necessity must involve a range of personnel covering a siteÆs commercial, operational and environmental interests and responsibilities. The challenge to be collectively faced by these stakeholders is to strike the correct balance between risk and cost. On the other hand, the challenge to be faced by technical services support personnel is to provide stakeholders with information in a format that they can use with confidence. This paper presents the application of continuous operational simulation (OPSIM) modelling techniques to establish appropriate risk profiles for minesite operations. It is necessary that the format of these risk profiles be generic and equally applicable for defining the risk of occurrence for a relatively comprehensive range of activities û eg from of a non-compliant discharge, to the risk of failure to meet production targets. What is more, the profiles need to be quantitatively based and capable of reflecting change in system response to varied operational or management strategies. The techniques presented in this paper are based around a key assumption that long-term records of the climate contain within them sets of sequences that are representative of what can be expected in the future û that is, the droughts, floods, cyclones, good years and bad, long or short, and everything in between. Therefore, if these historical records are run through an OPSIM model for a particular site, then the simulated operational characteristics can be taken as being representative of what can be expected in the future, in the long-term. This lends itself to statistical analysis and translation into the required risk based format. Water Solutions Pty Ltd have been working with Capricorn Coal Management to develop a relatively comprehensive OPSIM model of their operations at German Creek Mine, Central Queensland. Outcomes from the modelling have been used in recent times to provide mine management with risk-based guidelines for both securing and containing mine water inventories. One of the more interesting tasks has been to establish risk based inventory levels that, if reached, would trigger the immediate implementation of a contract for the desalination and re-use of mine water, at predefined rates. Also, lead-time warning of the occurrence of a possible trigger is of importance to operational and commercial planning. To service this requirement the OPSIM model is regularly used to produce lead-time estimates to defined levels of confidence. Case studies of these, and other, applications of the OPSIM model at German Creek Mine are presented in this paper and serve to demonstrate an effective methodology for practical risked based water management.

Jan 1, 2003

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003