Search Documents

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

The comparatively low winter rainfall, exposure to heavy salt laden coastal winds, and the consequent high evaporation rate, are important considerations in the rehabilitation of the Maslins Beach Sand Pit. The deficit of rainfall over evaporation is assessed at 1085 mm per annum. Such a coastal environment complicates the establishment of plants. The endemic flora found on the Sand Pit environs is mainly low wind-planed shrubs and mat plants. The dunes near the coast support an association dominated by Atriplex cinerea, Spinifex hirsutus, Scirpus nodosus, and Olearia axillaris. The coastal cliffs carry a more diverse vegetation dominated by Beyeria lechenaultii and Eutaxia microphylla. Overburden is used to develop a new landscape to screen operations, batter final faces, and cover rubbish at the nearby Council dump. The early overburden dumps were built with little regard for stability, but the more recent practice of using scrapers has resulted in more stable dumps. The erosion problems created by poor compaction have been controlled by contour banks, diversion drains, bitumen lined run-off drains, and hay mulching.

Jan 1, 1976

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

Coal water mixture (CWM) is a mix of finely ground coal with water and a small amount of chemicals. It is a new way of transporting and handling coal. CWM can be transported, stored and burned like fuel oil in steam generating boilers. It also has some environmental advantages over both oil and bulk coal. A group comprising Ube Industries Limited, Nissho Iwai Corporation (both from Japan) and Coal & Allied Industries Limited has been working in Japan and Australia since 1987 on a joint feasibility study into the production, transport and marketing of CWM from Australia to Japan. The group has been studying the development of a large-scale CWM plant on Kooragang Island at the mouth of the Hunter River at Newcastle, NSW. The project concepts and engineering plans for the CWM plant are well advanced and other studies related to the project are continuing.

Jan 1, 1995

The latent conditions clause in various general conditions of contract have traditionally proved to be a source of significant disputes in tunnelling contracts, even when extensive geotechnical investigations have been carried out at the tunnel site and a report of these investigations provided with the tender documents, informing the contractor of the nature and extent of subsurface conditions likely to be met with during execution of the works. This paper discusses the contractual aspects of the new latent conditions clause in the recent Australian Standard AS 2124-1986, General Conditions of Contract, in relation to tunnelling contracts. A comparison of this new clause is made with other latent conditions clauses in general conditions of contract in use in Australia and other commonwealth countries. It is seen that the new latent conditions clause in the recent Australian Standard 2124-1986 has, by providing for a reasonable apportionment of risks, attempted to minimize contractual disputes relating to latent conditions in tunnelling contracts and to provide a satisfactory basis for quick and efficient settlement of such disputes should they arise during execution of these contracts.

Jan 1, 1987

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988

By Winter W, Steele DA, Trudu AG, Gray CM

The Luzon arc extends for about 900 km from Taiwan to the island of Mindoro (central Philippines); in this area late Tertiary to Recent volcanism is considered to be the result of eastward subduction along the Manila Trench. The arc is composed of five segments, all of which have individual characteristics with respect to tectonic setting and magma chemistry (Defant et al., 1989). From the north to the south these are (Fig. 1): (1) the eastern Coast Ranges of Taiwan and the islands Lan-Hsu and Lu-Tao (Taiwan Segment), (2) the islands off the north coast of Luzon (Babuyan Segment), (3) the Northern Luzon Segment, (4) the Bataan Segment, and (5) the Mindoro Segment. Defant et al. (1988) suggest that the Bataan and Mindoro segments of the arc, both of which are characterized by different isotopic compositions and levels of large ion lithophile element (LILE) enrichment in the lavas, are separated by a 'pull-apart' zone, the Macolod Corridor.We are currently studying the mineralogy and petrochemistry of Late-Miocene to Pliocene volcanism in the Northern Luzon Segment (NLS), which comprises the geographic area of the Cordillera Central. This area has so far received limited attention, inspite of its wealth of porphyry copper, skarn and epithermal gold deposits. In this contribution we report the first results of our study of igneous rocks from the Mankayan Mineral District (MMD) which is located in the centre of the arc segment under consideration.

Jan 1, 1990

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By S Choy

Aquatic macroinvertebrates have been used as a monitoring tool for many years. They are ubiquitous and occupy a central role in the ecology of rivers. They are a key link in the aquatic food chain, forming a pathway between primary producers (such as algae and macrophytes) and predators (such as fish, platypus and birds), and some are sensitive to flow conditions, water quality and habitat condition. They are not very mobile and are good indicators of local impacts. As most aquatic macroinvertebrates are benthic, they are better able to integrate effects of changes in water quality, and habitat condition and structure. Their diversity is crucial to the maintenance of a balanced, functioning and healthy river ecosystem. Thus, data on benthic macroinvertebrate community structures can be used for predicting potential impact, assessing the extent of damage and for gauging recovery from damage. Over the past eight years, State agencies throughout Australia, through the National River Health Program have developed models (AusRivAS) to assess river health using macroinvertebrate communities. The Queensland Department of Natural Resources and Mines has sampled both macroinvertebrates and water quality throughout Queensland, including areas affected by mine discharges. This paper will assess results obtained from sampling in the Mt Morgan area to illustrate the usefulness of this method of river health assessment.

Jan 1, 2003

By P J. Hansen, D G. Franklin, M E. Trim, J V. Myers

The Northern Sewerage Project (NSP) is an upgrade to one of MelbourneÆs ageing, under-capacity trunk sewers. It will reduce the volume and frequency of wet-weather overflows to the Merri and Moonee Ponds Creeks and facilitate new housing developments in the northern suburbs of the city. A total of 12.4 km of tunnel and eight vertical access shafts will be excavated as part of the two project stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water (MW) and Stage 2 (NSP2) will be owned and operated by Yarra Valley Water (YVW). The owners require the project to have a service life of 100 years, a requirement significantly beyond many of the current Australian Standards, which aim to achieve service lives greater than 60 years but are typically assumed to achieve 40 to 60 years. Because of the potentially corrosive natures of the external environment along the tunnels and the internal sewer environment, durability was a key concern for NSP1 and NSP2. Stringent specifications were applicable to the tunnel lining systems. This paper describes the corrosive environments impacting NSP1 and NSP2, explains the key design differences between the two stages and details the lining systems considered and selected to achieve the clientsÆ desired 100-year service life. The project design is complete and construction began in 2007.

Jan 1, 2008

By B Leyland

The media in Australia is currently rife with articles and pronouncements on global warming as the most significant crisis of our time, which may æthreaten the future of civilisation as we know itÆ. This has been recently reinforced by release of Al GoreÆs film æAn Inconvenient TruthÆ, and one would be led to believe that the science of global warming is settled. And yet there is a strong body of literature disputing this apparent consensus which suggests that care should be exercised in introducing radical policies to solve a crisis which may not be real. Such policies would have a major impact on those in professions such as engineering (project approvals and design to minimise greenhouse gas emissions), accounting (carbon tax issues) and the law (corporate disputes on greenhouse gas issues are already in train in the USA). This paper addresses the hysteria apparent in the climate change debate by presenting factual evidence relating to climate change and the current phase of mild global warming. Some of the more extreme statements on future impacts are repudiated with published data, and alternatives to the purported role of fossil fuels in temperature change are offered. The potential impact of political decisions on professional activity is discussed, as are the implications of a possible future reversal of the scientific consensus, as has occurred in the past. The paper concludes with a call for the professions to exercise their Learned Society role to ensure that a rational and public debate is held on the broad issue of climate change.

Jan 1, 2007

By Andrew R. L

The Kintyre uranium deposit was discovered in 1985 in the course of following up radio- metric anomalies generated in an earlier air- borne survey. The latter survey was conducted primarily to acquire aeromagnetic data for diamond exploration and the uranium discovery was made during a subsequent campaign of base- metal exploration. CRAE commitment to the Rudall area for a range of commodities over a period of 13 years made a significant contrib- ution to the discovery of Kintyre. Other con- tributing factors included CRAE's multicommod- ity approach to exploration, management support and continuity in the geological team. The Kintyre uranium deposit (Fig. 1) is located on the northern margin of the Rudall Metamorphic Complex, 60 kilometres south of Telfer and 260 kilometres north northeast of Newman, in the Paterson Province of northern Western Australia. It is 700 metres inside the northern boundary of the Rudall River National Park (15695 sq. km) and lies between the Great Sandy Desert and the Little Sandy Desert (Beard, 1969). Intense weathering since the Permian has produced a subdued landscape around the deposit. Resistant rock types still retain an older plateau surface but it is incised by more recent streams. Other Proterozoic and Permian rocks form low, sometimes rocky, areas largely covered by aeolian sand.

Jan 1, 1988

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

By Kidman B. E

The Fitzpatrick area is the deepest section of the North Mine, with the orebody located between 1450 and 1800 m below the surface and some 600 m NE of the main No. 3 Shaft orebody and separated from it by the intensely sheared Globe Vauxhall Shear Zone. Development towards the Fitzpatrick area commenced in 1977 after earlier initial exploration drive development. However, it was not until 1982 that mining in the Fitzpatrick area actually began with the silling out of No. 36 level at a depth of some 1600 in. Since that time mechanised cut and fill mining from an incline ramp system with connecting stope accesses has progressed some 25 m above No. 36 level. Initial sill development on No. 37 level at 1660 m depth also commenced in July 1987 to further develop the Fitzpatrick area.

Jan 1, 1988

By Boyes B. A, Haydon D. J

The Paddington project is a gold mining and processing operation located 35 km north of Kalgoorlie in the Eastern Goldfields region of Western Australia (Figure 1). The project, which is operated by Pancontinental Goldmining Areas Pty Ltd, treats 1.25 Mtpa of oxidised gold ore, derived mainly from open cuts adjacent to the plant, with minor tonnages from other pits in the region treated on a custom-milling basis. Gold is recovered using a conventional CIL process. The process raw water supply of 3 500 kUd is derived from the local groundwater system. Average salinity of the raw water is around 90 000 - 100 000 mg/L total dissolved solids. A small portion of the raw water is passed through a vacuum distillation desalination plant to produce the project's 200 kUd requirement for high quality water for potable use and gold recovery.

Jan 1, 1988

By Royston D

Victoria has an extensive brown coal resource, 202,000 Mt, of which 43,300 Mt is regarded as readily recoverable. This brown coal is located principally in the Latrobe Valley as thick seams and is being extracted at low cost primarily to support base-load electrical power generation. The high moisture content of the coal is partially off-set in many applications by the high reactivity of the coal and the generally low levels of potential pollutants such as ash, sulphur and nitrogen in the coal. Large scale development of this brown coal resource began in the 1920's. In addition to electricity generation, it is used for briquette production, carbonisation of briquettes to char and was gasified for town gas supply to Melbourne (1956 - 1969). The BCLV coal to oil pilot plant at Morwell is a major new initiative in the use of Victorian brown coal. Many other new developments are in place and emerging in the utilization of low rank coals. Examples of these developments are, the large-scale gasification of lignites in the USA, and value-added products such as bulk chars, solid fuels, activated carbons and coal-water mixtures. The Government of Victoria has created the Coal Corporation of Victoria to promote current sales of briquettes and to encourage further new industrial developments based on the State's brown coal resources, in particular the Loy Yang coalfield. The Coal Corporation also has a vigorous product and process oriented research and development Programme.

Jan 1, 1987

By Gardner CE

Uranium occurrences and the probable Australian reserves are discussed and the recovery and processing methods used in treatment plants at Radium Hill and Port Pirie, S.A., Rum Jungle and Moline, N.T., and Mary Kathleen, Qid. are reviewed. The broad aspects of the application of nuclear power in Australia are then considered, and those factors of greatest significance are highlighted. It is these factors that are most likely to dictate the future role of nuclear generation in Australia. In commenting on private industry applications, the paper emphasises that each case must be considered on its own merits, and a warning is given that general statements can be misleading. In the long-term situation nuclear power is considered to be capable of playing a leading role and the discussion covers desalination and high load industries although short term applications appear difficult to justify. In non-power applications for nuclear energy reference is made to isotopes and the uses of nuclear devices in mining and civil engineering with a pertinent comment on safety.

Jan 1, 1970

By Hutchinson IN

In order for the Australian underground coal mining industry to achieve the high productivity rates demanded of it without compromising its good safety record, improved geotechnical monitoring systems are required. One of the main problem areas affecting underground coal mining is the deterioration of previously stable roadways.CSIRO Division of Geomechanics has been working on a NERDDC funded project to develop an instrument to monitor coal mine roof deformation. The instrument which has been developed, Roof Alert, is a self contained, battery powered, intrinsically safe device. It can monitor the magnitude and rate of deformation and give multiple, variable visual alarm signals where preset levels ate exceeded.

Jan 1, 1991