Search Documents

By Johnston S

A blending trial was conducted on 60 per cent Perseverance/40 per cent Rockys Reward underground ore at WMC Resources Leinster Nickel Operations to compare the benefits between batching and blending treatment of the two ore sources. Milling, f

Jan 1, 1997

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

Design of underground extraction layouts to protect surface improvements is an important area of subsidence research in the Coal Mining Engineering Branch of the Department of Mineral Resources, New South Wales, Australia. Some conventional partial extraction layout are important with reference to coal recovery and surface subsidence. The analysis ofsubsidence data collected from field surveys over longwall panels in the Southern Coalfield of New South Wales allows assessment of the effect of pillars left unmined between the longwall panels in reducing surface subsidence. The availability ofa wide variety of layouts with ranging degrees of surface movements affords considerable flexibility in designing layouts to suit a particular situation.Total extraction of coal should be the aim as far as possible. Partial extraction layouts should only be considered when surface subsidence movements caused by total extraction are not acceptable to the surface improvements.

Jan 1, 1985

Oaky Creek Coal (OCC) has embarked on an ambitious program to fast track the introduction of Trench Mining into its current mining operations. The project has the capacity to allow the extraction of reserves at stripping ratios, uneconomical by conventional mining methods.Trench mining using Continuous Highwall Mining (CHM) technology reduces the in-situ stripping ratio to 4:3; compared with a stripping ratio of 20:1 using conventional mining techniques.

Jan 1, 1992

By Barrett D

The paper discusses the justification for the Open Pit Mining Operation at Central Norseman Gold Corporation Limited's North Royal facility.Open pit mining history is outlined together with production statistics and associated costs. Underground mining practice is discussed together with an outline of the problems with mining in oxidised ground.

Jan 1, 1984

By Lindner E, Bosio M

South Australian coals are all low in rank and generally poor in quality, with difficult combustion characteristics. This circumstance makes the selection of a fuel source for future power generation difficult, requiring careful study and detailed analysis of the various alternatives. Combustion characteristics can have a significant effect on plant design and costs, and need early attention in any exploration and evaluation programme. The physical location of the deposits, often remote from established infrastructure and centres of population, is also a major factor in the ultimate cost of power at the poirl use.

Jan 1, 1977

By Ellyett C. D

This paper is an appraisal of the application of optical-mechanical-scanners operating in the non-photographic infrared wavelengths (3-5 and 8-14 micrometres) to mineral exploration in Australia. Pundamental principles of the operation of airborne scanners and their data output, thermal infrared (IR) imagery, are summarized. It is contended that thermal IR imagery often depicts the distribution of electromagnetic radiation emitted from earth surface materials better than aerial photographic techniques because optical-mechanical-scanners sample wavebands which straddle the wavelength peak of earth surface emission. To illustrate the geological features which such scanners can depict, reference is made to thermal IR imagery of a number of areas in Australia where the technique has been applied for exploration purposes. The images demonstrate that this technique can detect structural features like faults and folds, stratigraphic data by distinguishing different rock types and delineating their

Jan 1, 1973

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989

The Australian gold industry has in recent years experienced a tremendous growth period, though not to levels prevailing at the turn of the century. There are, however, a number of dynamic factors at play which collectively indicate that it would be unwise to assume that this growth will be maintained; indeed the future discovery of viable new deposits may be insufficient to prevent an industry decline in Australia.The higher gold prices of the 1980's together with technological advances, made previously worked mining centres areas of excellent prospectivity. These resources, signposted for us by the oldtimers, are being rapidly depleted. Whilst there can be no doubt that these resources can be replaced the real question is whether it is economic to explore for new deposits when it is likely that:The cost of future exploration will increase as exploration must focus on grassroot areas with few signposts. Almost by definition this primary exploration effort will be subject to a lower success ratio.The cost of future exploration will increase as new deposits will be located in more remote areas and at depth.

Jan 1, 1986

By M Coulthard, J Rivalland, K Dugan

Prior to 2001 Yallourn Mine has pumped approximately 1000 Megalitres of water per annum from aquifers beneath the mine floor in order to control aquifer pressures that were thought to have an influence on mine floor and permanent batter stability. In 2001 one of the deep aquifer pumps was shut down for five months in order to measure the aquifer recoveries. Prior to the shutdown a UDEC model was created in order to predict what level of recovery in the aquifer pressures would be critical to mine stability. The shutdown showed that the aquifer levels recovered and stabilised at levels that did not threaten the stability of the mine. The aquifers recovered to levels below the critical levels identified in the UDEC model.

Jan 1, 2003

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Fry P. R

Dragline operations have played a major and successful role in coal mining around the world for more than 30 years. Because of this long history, many of the operating draglines are reaching an age where maintenance and downtime costs are prohibitive, and decisions need to be made to either replace or refurbish them.In the current economic climate, refurbishment is a popular choice and this usually involves major structural repairs above and below the roller circle, together with replacement of the roller circle components. Often, the dragline tub is also replaced by a completely new one.

Jan 1, 1992

By Orid A

A fast, non-contact technique for measuring sizes of rock fragments on a conveyor belt is presented. An image processing technique called active stereopsis is used which makes use of a light stripe projected on to the surface of the fragments on the conveyor belt. A CCD TV camera is used to capture the shape of the distorted light stripe. the video image of this shape is then processed by a computer program so that the 3D profile of the surface can be obtained by triangulation. The sizes of the rock fragments are then calculated from this profile. The speed of the technique is improved by calibrating the light stripe system before measurement begins so that the profile of the fragment surface can then be measured using simple geometry. The technique is fast and highly parallel so that it is able to operate in real time.

Jan 1, 1990

Any project carries a number of challenges and risks. Inappropriate design, poor project management, time, industrial disputation and capital over runs are all areas which can impact on a project cash flows and return on investment. In the resource Industry you have the added complexity and risk of geology which is difficult to predict and sometimes unforgiving. The Dartbrook Mine was designed and constructed as a high output longwall mine and has overcome a number of hurdles to produce over 2.3 million tonnes for the first year of operation. A number of problems were encountered during construction which resulted in the inseam development being delayed for six months. Dartbrook people have demonstrated they can manage adversity and produce world class results. The mine has been through a very steep learning curve during 1997 and with this experience behind the mine is now producing at an annualised rate of 3.4 MTPA.

Jan 1, 1998

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995