Search Documents

By Durucan S

The southern Attiki peninsula is a very interesting area from an environmental point of view. The port and the city of Lavrio is situated at the east coast of the peninsula with about 10 000 inhabitants and there are also a few villages in the vicinity. The south-eastern part of the peninsula hosts the famous Lavrio mines which exploited the silver bearing orebodies of the area for more than 25 centuries. As a result, soils around the city of Lavrio are polluted with high heavy metal loads. The area is also of archaeological interest, as there are well preserved remnants of ancient mining and processing plants and archaeological sites. Soil samples collected from an area of approximately 120 km2 around Lavrio were analysed for their metal contents and the spatial distribution of the concentrations of ten selected elements were estimated from these data sets. The spatial data analysis and transformation capabilities of Geographic Information Systems, combined with extensive mining and geological data, helped the authors to identify the extent and causes of metal pollution around Lavrio.

Jan 1, 1995

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By J J. Frausto, G R. Ballantyne, M S. Powell, R Cruz, K Runge

Hydrocyclones are the most widely used device for classification in a grinding circuit. However, even the most efficient hydrocyclone has a bypass of fines from the feed to the underflow which reduces comminution circuit performance, as well as misclassification around the cut point. Fine screens classify only according to the particle size, allowing for a reduction in the recirculation of fines back to the mill. The development of high capacity multi-screens makes fine classification in a grinding circuit a viable option. Minera Saucito recently substituted hydrocyclones with screens in its grinding circuit. The change of classifier resulted in an increase in throughput and lead recovery but a decrease in silver recovery. This case study presents the changes in comminution and flotation performance that occurred after the installation of screens and uses historical operational data collected over 12 months of operation to investigate the reasons for these observed changes. CITATION:Frausto, J J, Ballantyne, G R, Runge, K, Powell, M S and Cruz, R, 2017., in Proceedings MetPlant 2017, pp 298–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

Infrastructure is defined as all those parts of a mining development which are not directly concerned with mining and mineral processing. Infrastructure is of significant and growing importance in the overall develop- ment of mines, and the costs could be critical in determining the viability of a project. Prior to_project authorisation, feasibility studies are required, often in considerable detail, to determine costs with adequate reliability. It is necessary that the Engineer should be adequately briefed for carrying out these studies and that good liaison and communication with the Owner be maintained. Methods, costs, order of accuracy, and some special requirements of these studies are discussed. After project authorisation, rapid im- plementation of the proposals is generally desired. A suggested organisation and method for this implementation is presented and dis- cussed. Comments on fees, and particular points in the relationship between Owner and Consulting Engineer are given. Particular reference is made to differences in conditions compared with public works projects. Realistic attitudes of mind towards environmental matters, industrial relations, and contractual relationships are advocated.

Jan 1, 1974

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

THE alkaline method for the estimation of zinc cannot, in the writer's opinion, be relied. upon to within very narrow limits between two assayers on unknown quantities of zinc. The end point is not decisive enough, and allows the personal factor toenter largely into the assay. The following investigation was undertaken to see how accurate the acid method is on Broken Hill concentrates and ores, and what should be the limit between the results of two assayers. The method adopted is as follows:Weigh sufficient amount of ore to give titration (between 20 and 50 cc.), place in tall 400 cc. beaker, cover, add 7 cc. nitric acid and heat till brown fumes cease to be evolved. Wash dock glass into assay, add potassium chlorate, evaporate to dryness on a slow fire with the beaker uncovered. When no smell of chlorine or nitric acid is observed, remove and cool. Add 100 cc. boiling water, then 7 grm. ammonium chloride, W cc. ammonia (.880 sp. gr.), boil for five minutes, filter, wash...

Jan 1, 1911

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

In those days no one worried - there were plenty of other things to do. But in'these days it is different. Everyone worries- and. because there is so much worry, emotion has entered the picture. And, worse than that, capital is being made in political circles. People who were quite unaware, five years ago, that any problem existed, have now become experts on the subject, and shout to high heaven that something should be done - and yet they go on using the leaded high octane petrol they deplore so much. And even scientists, who should know better, adduce only such evidence as fits the argument in hand. And the Press is not without blame - some of its reportings is open to serious question, whatever may be the excellence of its motives. The point is made that one should know what one is talking about. And make sure that the evidence quoted is fact - and make sure too, that all the evidence is used, not only that which suita the argument.

Jan 1, 1971

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By K Bojarska

Examination of wastes aimed at evaluation of their usefulness for utilisation needs applying modern chemical testing methods. The XRD-XRF-ICP-GC/MS set of test methods constitutes an integrated testing system enabling ecochemical examination of wastes. As far as the problem of time-consuming operations is concerned, the offered system fits in a market-oriented field of activity of accredited chemical laboratories. Within a reasonable period of time, it allows to obtain information about mineralogical and chemical properties of wastes. It provides full range of information beginning from mineral composition (XRD) through chemical composition including the number of elements and organic compounds (XRF-ICP-GC/MS) up to the contents relating to the amounts of ingredients, both organic and inorganic in the leaching tests (ICP-GC/MS). The XRD-XRF-ICP-GC/MS testing system proves to be of particular importance in obtaining reliable results enabling to perform precise assessment (from ecochemical point of view) of wastes to evaluate their usefulness for utilisation in building materials, in civil engineering and reclamation works.

Jan 1, 2003

The Joint' Venture Method is a procedure for assessing the value of exploration properties, particularly those for which resources have yet to be delineated. It aims to convert the terms of an actual or synthetic joint venture into the equivalence of an arms- lengths cash transaction between a willing seller and a willing buyer. This paper sets out one approach to achieving that conversion. It discusses both simple and complex cases and gives some examples from both public and private documents. It also includes some case studies in which the Joint Venture Method of valuation can be compared with values derived for the same project using other methodologies including actual cash deals. The Method has failings in both mathematics and logic. However because it does reflect or simulate an arms-length deal which takes into account past exploration effort and expenditure and an assessment of prospectivity at a particular point in time, it is felt that it can provide a reasonable approximation of trade value or asset value of a prospect, particularly if used in conjunction with other methods.

Jan 1, 1994

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

Gold bearing sediments at Scotland Point occur within the Quaternary Gibbston Fonnation, which underlies Cromwell Flat in Central Otago. Gibbston Fonnation unconformably overlies Teniary Manuherikia Group clays, sands and quartzose gravels. Gibbston Formation sediments are composed of a texturally diverse, multistoried lithostratigraphic succession of sandy/gravelly/bouldery lithofacies, deposited within a multiple channel (braided) depositional environment. Lithostatigraphic analysis indicate an upward overall decrease in average grain size, reflecting a concomitant reduction in stream competence. This trend results from progressive channel abandonment as major distributaries avulse across the outwash plain. Grade distribution of alluvial gold is controlled by aggradational and to a lesser extent degradational lithofacies deposited as distinctive braid bar forms near the base of the sequence. These lithofacies were deposited at different topographical levels on the outwash apron, under variable hydraulic conditions. Recognition of large-scale auriferous bedforms within the braid bar depositional system coupled with an understanding of lateral facies relationships, allows headgrade control on run of mine ore and quick determination of overburden to ore ratios.

Jan 1, 1988

By G Pasin, F Wirfiyata, G Khomaeni, W Valery, A Maclean, A Jankovic

The grinding circuit at PT Newmont Nusa Tenggara (PTNNT) – Batu Hijau mine consists of two SABC (semi-autogenous milling, ball milling, pebble crushing) trains, including four 20'?×?33'6? ball mills that have been lined with steel liners since the commissioning of the plant in 1999. During 2011 and 2012 an industrial trial was conducted to evaluate Poly-Met liners (a combination of rubber and steel liners). These new liners were installed in two of the ball mills (ball mills 1 and 2) and operated in parallel with ball mills 3 and 4 with steel liners.The objective of the trial was to compare the plant performance with the Poly-Met and steel ball?mill liners with regards to wear life, mill throughput, grind size and total unit costs. The trial was conducted over the entire life of the liners. The evaluation methodology implemented consisted of frequent spot sampling around the ball mill circuits, complete surveys/audits in both ball mills, and detailed analysis of process data. This paper presents the results of the industrial trial and main conclusions.CITATION:Maclean, A, Wirfiyata, F, Khomaeni, G, Jankovic, A, Pasin, G and Valery, W, 2014. Ball mill Poly-Met liner evaluation at PT Newmont Nusa Tenggara – Batu Hijau mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Y, Li Jianxiong, Hu Hua, Gu Desheng

After having briefed the technical and economical advantages of continuous mass mining in underground metal mines, the authors discuss the four stages of research and development of continuous mass mining in China. The four stages are: vibrating ore drawing in a stope, continuous mass mining in a stope continuous mass mining without rib pillars in an area and continuous mass mining in whole mine. The authors briefly review the research achievements of the first and the second stage; Combining the key national research project of the æNinth Five Year PlanÆ ù æThe experiment and research of continuous mass mining without rib pillarÆ, the authors introduce in detail the technological condition of mining, the design ideas of continuous mass mining, the design scheme of mining, the technology of mining. the equipment of mass mining, the chief research achievements and so on. The success of research of continuous mass mining without rib pillar indicates the arrival of the third stage of research. The introduction of continuous mass mining will promote the technology revolution of mining in China remarkably. The authors also point out that the development direction of continuous mass mining of the 21 century is continuous mass mining in whole mine, which is the fourth stage of research.

Jan 1, 2000

By A E. Levett, J Durbin

The environmental, social and governance (ESG) obligations of mining companies promote the consideration of water and land resources as well as the post-mining employment opportunities following the cessation of mining operations. This work aims to outline the potential for a mining operation to use their brackish mine water resources to support microalgae production, generating high-quality organic carbon sources to support their mine rehabilitation and closure outcomes. Microalgae production is an established commercial process for high-value products including vitamins, cosmetics and food supplements. On mine sites, microalgae production offers several major environmental and social opportunities: (i) carbon capture, (ii) metalliferous water treatment, (iii) acid mine drainage prevention, (iv) beneficial reuse of brackish mine water, (v) accelerated soil formation and (vi) post-mining employment (Levett et al, 2023).

Aug 2, 2023