Search Documents

The nickel refinery at Yabulu consumes an average of 118,000 kg/h of low pressure steam in stripping operations to-recover ammonia and carbon dioxide from product liquor and ore tailings streams. The steam used in the stripping operations is produced from the 25 MW power generation plant at the refinery. The back pressure on the non condensing steam turbines is maintained at 60 kPa.Studies have been carried out to determine the optimum amount of steam required to be generated for stripping operations. When steam production is increased, the product liquor flow from thewashing thickeners can be increased. This results in improved washing efficiency of the thickeners and therefore improves the plant nickel recovery. A computer thickener wash model was used to predict nickel recoveries at varying steam consumption rates.The studies have shown that in most plant situations, it is not economical to-generate more steam than that already available from existing power production.The studies also highlighted the necessity to use all steam generated from power production at all times to maintain maximum nickel recovery.

Jan 1, 1985

By N G. Corner

A sea bed sampling programme by CRA Exploration Pty Limited over an area of 12 000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 106 m and contained a high grade core of 33 km2 which averaged 283 mg/m3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10 - 40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 h turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By Muir D

A review of the various methods of degrad- ing cyanide either from gold processing liquors or electroplating baths is presented with some discussion on their relative merits or problems. Whilst alkaline chlorination is common practice in many U.S. and Canadian plants it poses particular problems for certain plants. Alter- native methods include electrolysis, hydrolysis and air oxidation with activated carbon as catalyst which are also integral steps in the carbon-in-pulp process. A basic study of the degradation of cyanide ion has been carried out therefore to determine the effect of temperature, oxygen and carbon. It is shown that carbon is an excellent catalyst for degradation by air and likely to lead to higher losses of cyanide in a C.I.L. circuit. Degradation by hydrolysis is important at high temperatures and high pH such as employed in the Pressure Zadra or Anglo elution processes. Carbon catalysed degradation of cyanide by oxygen in effluent streams may be an environmentally acceptable alternative to conventional chlorine degradation.

Jan 1, 1987

By Liu H, Chen S

Natroalunite is one of colouring minerals in kaolin. In this investigation, natroalunite, on which Ca(II) was adsorbed, was flocculated by HPAM and kaolin was depressed in suspension. The adsorption of Ca(II) on the natroalunite surface was studied by zeta-potential measurement and Auger Electron Spectroscopy analysis. Ca(II) was adsorbed more on the natroalunite surface than on the kaolin surface. The mechanism of Ca(II) adsorption was considered to be chemical adsorption on natroalunite and to be physical adsorption on kaolin. It has been found that Na6P6O18 and Na2Si04 can strongly affect Ca(II) adsorption on the surface of kaolin, but weakly on the surface of natroalunite. The effects of degree of hydrolysis and the molecular weight of HPAM, the effect of pH and the effect of Ca(II) have been studied. The kaolin ore, containing SO3 1.05 per cent has been processed with this method. The products only containing S03 0.36 per cent and the weight ratio of concentrate 52.27 per cent were Obtained.

Jan 1, 1993

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By R Mackay, J Brereton

On 30 June 2020, the Mine Land Rehabilitation Authority (the Authority) superseded the Latrobe Valley Mine Rehabilitation Commissioner as the independent overseer of Victoria’s declared mine rehabilitation. Currently, only the Latrobe Valley’s three brown coalmines are declared, with each mine at a different stage of rehabilitation and closure planning: Hazelwood ceased mining in 2017, Yallourn is scheduled to end mining in 2028 and Loy Yang in 2035. The three declared mines are very large, close together (Figure 1) and present significant environmental risks that must be mitigated during rehabilitation and post closure. In addition to fire risks, the brown coalmines are inherently unstable and require continuous monitoring and management of ground movements and groundwater pressures. Since 2007 several damaging events have occurred, highlighting the difficulties of achieving long-term stability, even with good landform design and rigorous ground control management plans

Aug 2, 2023

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By A L. Stewart, M Baatar

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Middle Palaeozoic Gurvansaikhan Belt (Southern Mongolia) of the Central Asian Orogenic Belt is one of Central Asia’s most significant emerging porphyry copper provinces. The belt has become the focus of extensive exploration for porphyry copper-gold deposits over the last decade following the discovery of the giant Oyu Tolgoi porphyry copper-gold deposit. The Gurvansaikhan Belt is known to host porphyry deposits of Late Devonian (~370 Ma) and Early Carboniferous (~320 Ma) age. The characteristics of Early Carboniferous porphyry systems are poorly known compared to their older counterparts, despite their probable abundance and potential economic significance. Exploration within the Kharmagtai porphyry breccia complex has identified multiple cogenetic gold-copper-porphyry centres and late-stage mineralised magmatic-hydrothermal tourmaline breccias emplacement within a composite high-K calc-alkaline quartz monzodiorite intrusive complex. Early porphyry alteration and mineralisation at Kharmagtai are zoned around vertically attenuated early- and inter-mineral quartz monzodiorite dykes and stocks and comprises a complex sequence of calc-potassic, potassic and propylitic assemblages. Hematite dusting is a common alteration product that gives intrusions and the host rocks a distinctive pink-orange colour. Several of the systems have bornite-rich cores, where mineralisation is characterised by high gold grades (0.7 to >5 g/t Au) that zone outward to chalcopyrite-rich and then outer pyritic halos. Early stockwork mineralisation is overprinted by magmatic-hydrothermal tourmaline breccias. High-grade magmatic-hydrothermal tourmaline breccias form part of a major copper-gold mineralised breccia system with significant exploration potential. The Early Carboniferous porphyry copper-gold systems of the Gurvansaikhan Belt represent a substantial exploration challenge in an area of increasing exploration maturity. This paper summarises the characteristics of the Kharmagtai porphyry system that have helped to define the Early Carboniferous porphyry province of the Gurvansaikhan Belt and discusses implications for future exploration.CITATION:Stewart, A L and Baatar, M, 2015. The Kharmagtai porphyry breccia complex – characteristics of early Carboniferous porphyry mineralisation in the Gurvansaikhan Belt, Southern Mongolia, in Proceedings PACRIM 2015 Congress, pp 383–388 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

By M Chiquito, R Castedo, P Segarra, L M. López, J A. Sanchidrián, J Navarro

The aim of this work is to assess the performance of different constructive solutions against explosions on the strength of masonry walls. The solutions tested, namely an external metal mesh, a glass fibre film on the external face of the wall and a basalt fibre film located on the inner face of the wall, have low to medium cost and are originally designed for other purposes, like seismic protection. Four cubic boxes 3 × 3 × 3 m were built using each of the solutions and typical masonry blocks. In the tests, a spherical plastic explosive initiated in the centre was placed at scaled distance of 2.9 m/kg1/3, so that moderate damage would be caused on the wall. In order to assess the performance of the explosive, pressure gauges were placed at the wall and at different distances from the explosion. Additionally, vibrations were monitored with seismographs in the far field and a high-speed camera was used to estimate the shock wave velocity during the tests. The resulting damage has been evaluated on 13 points of the external wall of each box using a rebound hammer. Damage maps have been drawn for each wall based on these measurements and damage has been assessed inside the box considering the fragments mass launched during the test. The use of external metal mess leads to a decrease of 34 per cent on damage of the external wall and 38 per cent reduction of spalling. The use of a film in the inner wall provides a strong reduction on spalling.CITATION:López, L M, Segarra, P, Castedo, R, Sanchidrián, J A, Navarro, J, Santos, A P and Chiquito, M, 2015. Performance of different constructive solutions against explosions in full-scale masonry walls, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 819–824 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Romanel, M S. Kato, M P. Piermatei, P Artioli

"Brazil is the sixth worldwide producer of aluminum and Votorantim (Metals) has been operating three bauxite open pit mines in a particular way of working. In those the deposits occur on the top of hills, under forest, coffee, eucalyptus plantation or pasture area.The deposits are not large and normally mining takes an average of two months to be completed before starting the rehabilitation process, which demands a good strategy in mining planning to achieve the production goals.The benefit function developed to select feasible areas uses, beyond production costs, fees from the owner by using their area and rehabilitation cost. Both are based on land use and occupation field survey data. In this process each area with different land use receives a specific rehabilitation cost as input into a block model.Once the selection is made the mining schedule begins, taking into consideration the following premise: the orebody needs to be mined in a short period of time because during this time, the surface owners receive from Votorantim a compensation based on the expected profits from their plantation or pasture, plus royalties related to the ore amount existing in their area.Not all operations have waste dumps. Waste is pushed down by bulldozers to the lower part of the ore border. After loading and transporting ore, the waste is handled back to the mined area to fit the topography. With this step concluded, the mined area is directed to the environmental team who, alongside university partners, develop land reclamation to return them to their owners, eg in 2011, 110 ha were rehabilitated of which 29 per cent is native forest.Votorantim closes many mined areas a year and currently the entire mine planning considers this particular way of operation, making profit with minimum interference with the community and the environment.CITATION:Artioli, P, Kato, M S, Romanel, A and Piermatei, M P, 2012. Environmental variables at bauxite mine, in Proceedings Life-of-Mine 2012 , pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

Dr Eric Bumstead is to be commended for his recent paper on gold analysis, published in the March 1984 Proceedings. It is not often that someone in industry, rather than academia, takes the time to collect and report on such a volume of data, data which is of interest to everyone involved in gold exploration and development.After reading the paper I felt, as a geochemist and as ayer, that there was another side to this whole question of analysis that few people are aware of, i.e. the problem facing a laboratory and how the laboratory can try to give the customer maximum value for money spent.Analyses for gold are carried out for different reasons, depending on the aims of the geologist or metallurgist who presents the samples. These can broadly be separated into three classes, to answer the following questions.1. "Is there any gold in this sample?"2. "Approximately how much gold is there in this sample?"3. "How much gold is there in this sample?"In every case there is a different balance between accuracy and precision, cost and avoiding chemical problems. By "chemical problems", I mean such possibilities as samples containing high levels of sulphides, gold present as tellurides, cyanide being present, contamination with mercury, and other mineralogical oddities, plus problems such as samples containing grease.There is no such thing as one assay to cover all possibilities.Samples in category I come mostly from early stages of exploration.There are often large numbers of samples, their mineralogy is not well known and hence chemical problems could exist, but the explorer wants assays at a minimum level of precision and expects minimum cost. These characteristics do not easily come together, for although the precision required is low, the accuracy required is high at low levels. A small positive result when the true answer is nil could lead to a fruitless search and a waste of money. Conversely, a nil result, when the true answer is a small but significant level of gold, could lead to the passing over of an area that may warrant further work.Because there are conflicting requirements for this type of assay, the methods chosen must be a compromise and different assayers will balance these requirements differently and come to different conclusions. The methods cover sample preparation, assay sample size and variations in assay techniques.

Jan 1, 1984

By A G. Dempster, B McKeown, S Saydam, J Coulton

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

The Coke Ovens Laboratory at Australian Iron & Steel, Port Kembla has been involved in the analysis of seam gases and mine airs for approximately twenty (20) years. This period has seen many developments and changes in the techniques used to the point when the current techniques are equal to other labora- tories involved in similar analyses. The laboratory has NATA registration for the analysis of mine airs and gases. Apart from routine testing of seam gases, ventilation airs and gases emmitted from coal bore cores a number of projects have been undertaken. These have served a twofold purpose, one to provide information to the customer, generally Collieries Research and Technology and secondly in developing the skills and capabilities of the Coke Ovens Laboratory. This paper discusses the development and services available at the Coke Ovens Laboratory for the analysis of gases and airs from collieries.

Jan 1, 1983

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

By Young JA, Rogers G, Bannister S, Edwards SA

Many coal mine operators have responded to economic pressures by massive investment in machinery to reduce unit costs. To sustain the increased production which must justify the expenditure it is essential to know the resource in great detail months or even years in advance of its extraction. The required detail includes variations in composition and any lateral disruptions to the seam which night affect production. As Wilson (1985) has pointed out, a day's production loss can mean half a million dollars income forgone, and an unexpected major fault can mean a shutdown of weeks. Traditionally, seams were probed by surface drilling on (typically) 250 or 500m centres, and by horizontal drilling from sithin'the seam. Core was analysed chemically. The new generation machinery cannot tolerate the risk attendant on such widely spaced sampling, but the costs of much closer sampling rapidly become prohibitive.

Jan 1, 1987

By Tonkin D. A

Poor performance in the several stages of the magnetite recovery circuit, coupled with poor desliming through inefficient and over- loaded desliming screens, led to excessive magnetite consumption. An accurate and reliable sampling programme was established covering all outlets of the plant. Emphasis was placed on frequency of increments in an endeavour to detect extreme conditions of short duration. Systematic checking of the entry points to these outlets than identified those sections of the recovery circuit at fault, namely magnetite recovery separators and the heavy media cyclone product rinsing screens. More product rinsing water was provided, and modifications to the rinsing screens improved the efficiency of these units. Consistency of operation through automatic control of level eliminated the sudden massive losses in the magnetic separators. Load on the recovery circuit was then reduced by improvements to the raw coal desliming screens. A 50 per cent reduction in magnetite consumption was achieved.

Jan 1, 1974