Search Documents

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

By C Tapia Cortez, C Sammut, S Saydam, J Coulton

‘Like every other commodity, the value of the metals is subject to variation’ (Ricardo, 1817). Mineral commodity price uncertainties have always been a significant issue in mining business due to the close relation between global economic conditions and commodity prices, which commonly generates significant and unexpected price fluctuations. Price forecasts have been driven by economic theory, which states that in the long-run market will be balanced and that prices tend to the marginal cost of production. However, this theory has been misunderstood in the mining industry and future prices through time, in real terms, are assumed to be unchanged. This is unrealistic due to regardless of the cycling nature of economy and the omission of uncertainties. Furthermore, using historical data in traditional price forecast approaches does not guarantee realistic predictions as past events will not necessarily be repeated at the same intervals and with the same intensity. Mining, finance and economic sectors have made significant research efforts to predict prices and control uncertainties through classic linear, Gaussian and probabilistic simulation approaches. However, by definition, uncertainties cannot be measured or accurately modelled. Uncertainties can be identified to measure and manage the associated risks; therefore, uncertainties in mining projects have been historically misinterpreted, erroneously measured and poorly controlled. It is widely known that supply and demand functions drive market prices. While technological development noticeably influences supply, demand is strongly driven by psychological factors, mainly related to customer preferences and lifestyle expectations. Thus, human behaviour is one, or if not, the most important variable to determine commodity prices in a competitive market. During the last decades, alternative methodologies have been used to study uncertainties in human, environmental and market behaviours. Chaos theory, fractals, artificial intelligence and econophysics have been widely and successfully used to investigate complex dynamic systems to address uncertainties over time in the fields of neurosciences, meteorology, aviation and market trading. The application of these techniques in the market suggests a more realistic approach to the business environment. Through the combination of the methodologies above a novel long-run price uncertainties simulation approach that emphasise the differences between risks and uncertainties is proposed in this paper. CITATION:Tapia Cortez, C, Saydam, S, Coulton, J and Sammut, C, 2015. Copper price uncertainties – chaos theory to manage risks in mining projects, in Proceedings Third International Future Mining Conference, pp 261–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 µs, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

There are still vast areas of Australia in which either the hydrocarbon potential has already been indicated but from which no hydrocarbons have been produced or else are completely untested. Despite the lack of recent new oil discoveries, it is anticipated that initial gas discoveries in these areas will be followed by oil discoveries as has happened historically. General exploration activities are continually providing new information that is being input to update previous hydrocarbon assessments for Australia, and all indications are that future exploration efforts will discover a lot of gas, some small oil pools and there is a chance to prove a major new oil province. Because of this, it is anticipated that reserves growth will continue at the average historical rate of about 200 MMB/year until the year 2000. The most frequent scenario will be costly exploration resulting in small oil discoveries and high development costs. This, in the past, has resulted in low profitability for Australian oil exploration, but windfalls for the Australian government.

Jan 1, 1981

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By H Mansouri, M A. Ebrahimi Farsangi, F Faramarzi

A blast fragmentation model is developed based on the gamma function to describe the run-of-mine fragmentation distribution. The model presented is aimed to benefit from simplicity in application and also to be efficient in description of the fine to coarse part of the blast rock fragments. In fact, the gamma based model (KC-KUM), gives a unit distribution curve, which is made up of two separate equations, covering different fragment sizes in the muck pile. The generated values of the fines to central part of the equation and the central to coarse part of the equation are connected at the 40 per cent grafting point. For validation, eight production blasts, which were specially designed for this purpose, were carried out at an iron ore mine (Jalal-Abad iron ore mine/Iran). Results achieved by KC-KUM and two of the most well-known models. Kuz-Ram and Swebrec, are compared with measured data. Moreover, to assess the models’ efficiency in presenting the best distribution curve, a Logarithmic error method is chosen. Based on the achievements. KC-KUM has the least deviations by the least absolute log error of 0.52, whereas the values obtained for the Swebrec and Kuz-Ram models were 0.79 and 1.34 respectively. Furthermore, the models were applied to predict X80 for 12 production blasts carried out at Gol-e-Gohar iron ore mine/Iran. These predictions were compared with the results from these trials. The coefficient of determination (R2) and root mean square error (RMSE) are calculated. Consequently, the highest R2 was obtained for KC-KUM at 0.837 with the least RMSE of 11.31. On the other hand, R2 and RMSE are equal to 0.832 and 20.19 for Swebrec; and 0.813 and 19.75 for Kuz-Ram respectively. The results obtained suggest the superiority of the KC-KUM model over the other two models in assessment and prediction of blast fragmentation in a reliable way.CITATION:Faramarzi, F, Ebrahimi Farsangi, M A and Mansouri, H, 2015. Prediction of rock fragmentation using a gamma-based blast fragmentation distribution model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 685–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By García B., Wolff E.

The pellet qualities primarily depend upon the thermal profile and gaseous environment during induration. During the induration of the pellet, it undergoes physical as well as chemical changes. Physical changes are mostly due to sintering and chemical changes are due to carbon burning inside the pellet. The effect of carbon on sintering is investigated on a single pellet scale using an optical dilatometer. Sintering is a complex process that involves transportation through various mechanisms. Sintering is quantified in terms of sintering ratio and the kinetic parameter, exponent ‘n’, under isothermal conditions is deduced using the power law equation. The value of n can be used to estimate the sintering mechanism at different isothermal temperatures. Also, the activation energy is calculated using the empirical Arrhenius equation. The activation energy of 0 per cent coke and 1 per cent coke-containing pellets are 531.0 kJ/mole and 552.6 kJ/mole respectively. The order of magnitude of activation energy suggests the same mechanism in both cases. Although the mechanism of sintering is the same, 1 per cent coke-containing pellet sinters more at any isothermal temperature.

Jun 17, 2024

By D Howe

The Athena gold deposit was discovered in 2007 by Gold Fields Australia Ltd, at the St Ives Gold Mine, 35 km southeast of Kambalda, Western Australia. Gold anomalism was identified in sheared Paringa Basalt as a result of a regional scale aircore drilling program, in association with geophysics. In the 18 months following discovery, the deposit was intensely drilled and by June 2009, it was announced that the Athena deposit contained an ore reserve of 1.7 Mt @ 5.6 g/t for 316 koz. This was followed by a feasibility study, and as a result mine development commenced in November 2009.The Athena mineralisation is hosted in a discrete, north-south striking, steep to moderately dipping shear zone within the southwest dipping Paringa Basalt. Vein intensity has a strong correlation to grade and vein type varies from early thin quartz-albite-sulfide (pyrite and/or pyrrhotite) shear parallel veins to strong brecciation and irregular veining with quartz-albite-actinolite-biotite-pyrrhotite infill. The geology preproduction process developed at the Argo mine was refined and improved following a business improvement project. The aim of the process is to construct detailed geological interpretations prior to development allowing informed mining decisions to be made. The process delivers significant cost savings and revenue enhancements.The development of macroscopic classification scheme was critical to determine ore or waste in the early phases of mining. The Style of Deformation, Alteration and Veining (SAV) Code was the result, and has been enhanced as greater geological knowledge is gained over time.

Aug 22, 2011

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15 000 tpa magnesium alloy production facility in Nanjing, China. Site construction commenced in February 2005, with installation of all major components completed by the end of October 2005. Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005. Since that time, ramp-up to the name plate capacity has been undertaken. This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By S M. Gover

Estimating the probability of failure for embankments is not intuitive. It requires not only an appreciation of the strength of the embankment, but an understanding of the variability and uncertainty in the strength parameters as well. These additional aspects are, in themselves, relatively new to most practicing engineers, and therefore require some discussion.This paper discusses the concepts of probability and uncertainty, and presents a reliability-based numerical experiment, together with a literary study and collation of some of the author’s historical slope stability analyses, to investigate whether a direct relationship between safety factors and probabilities of failure exists for certain levels of uncertainty in strength parameters. In doing so, a useful tool is presented whereby knowing the safety factor of a simple slope or embankment with a consistent level of uncertainty, one can infer an approximate probability of failure.CITATION:Gover, S M, 2018. Linking safety factor to probability of failure, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 384–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018