Search Documents

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

By R Dimitrakopoulos, R Goodfellow

One of the primary objectives when optimising a mining complex is to maximise its value for the primary stakeholders. In order to achieve this objective, it is necessary to holistically optimise all aspects of the mining complex, including decisions of when to extract materials from the available sources, how to blend or stockpile these materials and how to best use the available processing streams to satisfy customer demand. Existing methods for global, or holistic, optimisation ignore the compounded effects that risk has on the performance of a mining complex. Over the past decade, several stochastic optimisation approaches have been proposed to integrate various forms of uncertainty into the open pit mine design and production scheduling. These methods, however, are limited in their ability to simultaneously optimise the production schedules for the portfolio of mines, material destination policies, the use of the available processing streams and the various products that are produced at each location of the mining complex.This paper aims to discuss a new method for the global optimisation of open pit mining complexes with geological uncertainty. The proposed generalised methodology is capable of modelling and holistically optimising mining complexes, including aspects related to production scheduling, blending, stockpiling and non-linear interactions that often occur in practice, but are over-simplified in existing models. Two case studies are discussed to highlight the need for these complex, stochastic optimisers. First, a case study for a nickel laterite blending operation highlights the need to integrate geological uncertainty into the optimisation in order to ensure product quality constraints are respected. Second, a case study for a copper-gold mining complex highlights the added value when simultaneously optimising the production schedule and the stockpiling and treatment of extracted materials.CITATION:Goodfellow, R and Dimitrakopoulos, R, 2014. Stochastic optimisation of mineral value chains – developments and applications for the global optimisation of mining complexes with uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 13–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By S H. Sie, R Seetharam, K Naito, T Takagi

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medicallhigh-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnS2), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By C Buchanan

For a long time there has been a known relationship between the northern Heavy Mineral (HM) deposits of the Murray Basin to the extensive north east trending ridges in the area. These ridges have been a targeting tool for exploration and have uncovered some significant discoveries, some of which have turned into mining projects. Bemax’s Ginkgo and Snapper deposits are good examples of how the faulting helped create an economic deposit but also result in significant planning issues in the exploitation of these deposits. Material balance, induration and pyrite issues have been made easier to manage through good geological understanding of the deposits.

Aug 22, 2011

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Rayo

Andean countries (Chile, Peru, Bolivia and Argentina) have 42 semi-autogenous mills (SAG) in operation and there are more than 30 projects in the pipeline that consider SAG mills. At the end of the next decade, the total amount of SAG mills in this area will likely be close to 100.There is a lot of reliable operational information collected by JRI Ingenieria Sociedad Anonima, the author’s engineering company, for more than 20 years and processed by statistical software, to be used as a reference for design basis of future projects or to improve operations by comparison. JRI Ingenieria Sociedad Anonima has reliable information related to the performance of more than 50 per cent of the Andean SAG plants.The paper presented considers a set of graphs that summarise the collected and verified SAG plants technical data. The figures will show key parameters as circuits and equipment data, energy consumption, technical availability, utilisation rates, throughput variability, pebble productions, steel consumption and others.The data is compared with typical design basis of several engineering companies and the main differences are analysed and/or commented on.CITATION:Rayo, J, 2014. Comparison of semi-autogenous mills operations in Andean countries, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 283–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The theme of my address to your Institute, indeed its name, is "The Mineral Industry - What Next?" Knowing that I was required to make four appearances, and not wanting to be too repetitious, I wrote a rather long speech of which I will deliver various sections at different places, with a common introduction. Specific areas I have addressed are "Exploration", "New sources of minerals and energy", and "Mining and metallurgy of the future".

Jan 1, 1984

By S Juras

The terms measured resources and proven reserves denote the highest level of estimation confidence in all of the major classification schemes. But what do they really bring to today’s project or mine with respect to production planning and expectations? Initial reserve declaration does not need measured resources, just indicated resources. Economic viability of a project is assessed on total reserves with nary a bonus for the amount of proven reserves. Production plans are based on grade and tonnage goals that may only coincidently correspond to proven reserves. So are the measured and proven categories still relevant? Historically, and almost exclusively in underground mines, companies only allowed mining in areas of proven reserves. Some companies still follow that philosophy. But many others will mine a mixture of probable and proven reserves without hesitation. Also what of the undeveloped project in a new district – what is to be made of their declared measured resources and proven reserves? Measured resources are commonly set either by some type of proximity to data scheme or a matter of ‘feel’ based on the qualified person’s experience. The parameters for reserve conversion focus on the project as a whole and then a portion becomes classified as proven reserves almost solely based on whether the resource category is measured. So should the mining industry continue to use these categories of resource and reserve classification? This paper will present arguments about making these categories once again more relevant. A more disciplined usage of these categories may re-introduce their relevancy in public disclosures of resources and reserves. As well a more consistent usage in operations may lead to increased confidence in managing production targets and costs.

Aug 22, 2011

By T Barto, D Thomson, T Norgate, C Doblin

Collaboration between CSIRO Minerals and SunSalt Pty Ltd, a salt producing company located in rural Victoria, has resulted in a commercial process to recover magnesium sulfate (commonly called Epsom salt) from the saline waters of the Murray Basin. The feed for this process is bittern; the liquor remaining after halite (common salt) has been harvested from the saline water by evaporation.SunSalt produces salt and bitterns from three locations, namely Hattah (Victoria), Mourquong (NSW) and Wakool (NSW). The small size and considerable distances between these operations makes it uneconomic to build a stationary processing plant to extract value-added products, in particular Epsom salt, from the bitterns of the three operations. This fact led SunSalt to build a containerised mobile plant that could be moved to each site to process the bitterns at the end of the salt harvesting period.Epsom salt is extracted from the bittern by further evaporation, refrigeration and recrystallisation. In this process the bittern is diluted with five per cent volume of fresh water to minimise precipitation of residual halite in the bittern. Cooling the diluted bittern to between -5 and -10¦C precipitates up to 70 per cent of the magnesium sulfate, which is recovered as 85 to 96 per cent purity Epsom salt by filtration. This product is marketed as an industrial grade Epsom salt. Higher purity (up to 99.9 per cent) Epsom salt (USP or BP grade refined product) is made from the industrial grade product (raw Epsom salt) by recrystallisation.The containerised mobile plant was commissioned in December 2002. The raw Epsom salt generated in the mobile plant is refined to a higher purity Epsom salt in a separate plant located in Mildura. The Mildura plant was commissioned in December 2003.The CSIRO-SunSalt collaboration has demonstrated that the saline waters can be processed into a useful resource, and in addition could create jobs and a new skill base in regional Australia. The production of Epsom salt locally in Australia, which is worth currently about $A600 per tonne, removes the need to import over 3000 tpa from overseas with a net positive impact of $A2 million on the balance of trade.

Jan 1, 2004

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Carroll

Mining of the zinc, lead and silver deposit at the Broken Hill Southern Operations site has been occurring for over 100 years. As a result of this, a significant amount of high-grade ore is now taken from narrow remnant pillars left between old stopes and zones of previously mined ground. Stopes have been filled with either hydraulic fill (also known as ‘sandfill’), cemented hydraulic fill (cemented sandfill), waste rock backfill or a mixture of these fill types.In the last ten years, there has been considerable success mining through narrow pillars where sandfill is exposed in the development face and/or walls using a ‘shell’ support regime, wherein a layer of bolted mesh is sandwiched between two layers of sprayed fibrecrete (25 mm fibrecrete, then mesh and bolt, followed by a final 50 mm layer of fibrecrete). Shell support is also used in very poor, broken, relaxed ground conditions and in areas filled with cemented fill (sandfill with a minimum four per cent cement content).The next stage of innovation has been to develop a technique for mining through old stope voids filled with uncemented sandfill, known locally as ‘contours’ (old cut-and-fill working), an activity where unconsolidated sandfill can run at the face and from the backs. The challenge is to prevent exposed sandfill in the face and the backs from failing before it can be supported.To achieve this, the Southern Operations mine has implemented a technique in which 6 m long spiling bars are used to strengthen and stabilise the sandfill in front of the face. The hollow steel bars are driven in around the heading perimeter in a closely spaced pattern then pumped full of grout. The bars and the grout stabilise the sandfill in front of the face, preventing it from failing into the drive during excavation and prior to further support being installed.A final support system consisting of shotcrete, mesh, bolts and steel girders is installed as excavation progresses. Both the initial and final support systems are essentially passive support systems designed for a low-stress environment (as the stress originates mostly from the mass of unconsolidated sandfill).This process is slow and labour intensive. Fifteen separate cycles of people/machinery are needed to progress one equivalent heading cut (compared to six for a standard fibrecrete- and bolt pattern-supported rock face heading). This slow pace introduces scheduling challenges, but the process opens up parts of the orebody that were previously uneconomical to mine.CITATION:Carroll, D, 2014. Mining through sandfill using spiling bars, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The mining industry has expanded significantly in the Pacific Region over the past two decades through a mix of new developments and brownfields expansions of existing operations. Despite this overall success there are also a number of well publicised examples of less than successful minerals ventures. These problem developments highlight the fact that success cannot be taken for granted and that rigorous planning and attention to detail is essential. The dominant growth has come through expansion of existing businesses, notably alumina, iron ore and coal, achieved through both efficiency gains on existing plant and step change capacity additions such as new mines and/or expanded processing plant. This expansion has largely been linked to increased market opportunities. The major issues are the quality and extent of the host resource, achieving the market targets, and the efficiency of the expansion effort. There can be also a range of site specific issues which need to be addressed. The development of new greenfields operations is often more complex as it can bring a wide range of new issues. Depending on the nature of the development, and the companies involved, these can extend from initial financing through to obtaining a market position. Incorporating major new technology and/or establishing infrastructure and attracting staff to remote locations can also add significant challenges. This paper outlines many of the critical factors which need to be considered prior to proceeding with major expansions or greenfields developments. These will be linked to a number of developments in the region over the past decade.

Jan 1, 2004