Search Documents

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By J Seccatore, F Golin, E Munaretti, M Cardu, J C. Koppe, J Bettencourt

Contour blasting is commonly performed by employing linear charges decoupled from the boreholes. This method is common in surface and underground excavations, either for civil or mining purposes. To achieve the best results in terms of rock breakage and respect of the excavation profile, blasting theory suggests that charges should be inserted coaxial to the holes to grant uniform distribution of the explosive energy, therefore obtaining a uniform radius of damage. Nonetheless, due to readiness of operations or lack of availability of specific products on the market, non-coaxial charges are often employed in blasting practice. Non-coaxial charging methods include the employ of high-power detonating cord (40 to 100 g/m), low-power detonating cord connecting small-diameter cartridges (commonly 10 g/m detonating cord priming 1” cartridges) or string loading (a thin layer of bulk emulsion pumped with controlled flow and controlled extraction of the injecting rod). This research focuses on evaluating the effects of the first two charging methods on the quality of final walls in open pit and underground operations. Different drilling geometries and charging configurations were applied to both quarrying and tunnelling blasts. The half-cast factor, the overbreak and the underbreak were evaluated as control indicators. Rock quality designation and rock mass rating were used to classify the rock mass. The research was aimed to push contour blasts to their limits, observing for which geometry and charge configuration the blast lost its design threshold with respect to the final wall for every given rock mass. Results show the operational limits of non-coaxial charges encountered in the rock masses object of this study. In good-quality rock, smooth blasting with decoupled linear charge of 40 g/m can be extended to a spacing S = 22Øf with little or no detectable drawbacks in terms of final wall quality, in contrast with theoretical formulae for the determination of the radius of damage. On the other hand, when the rock is poor, any quality of the final wall is hardly achieved at all, in spite of any care in the details of execution of smooth blasting. It is concluded that any design criterion and theoretical approach modelling the effects of contour blasting cannot ignore the features of the rock mass.CITATION:Seccatore, J, Golin, F, Cardu, M, Munaretti, E, Bettencourt, J and Koppe, J C, 2015. Evaluating the effects of non-coaxial charges for contour blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 267–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

By D Thomas

Geochemical data related to AMD for the West Coast and Southland regions have been collated into a relational database and GIS system. The types of information include; rock geochemical data, water chemistry data and aquatic macro-invertebrate abundance data. This information will be combined with eco-toxicology experiments to determine impact thresholds on aquatic ecosystems. Ultimately these datasets will be combined with remediation investigations to produce a Framework to assist decision making related to mine planning, consent and compliance.   Current geochemical research examines the controls on As concentrations downstream of gold mining areas and the variability of AMD from Brunner Coal Measure rocks. Assessment of factors that control the chemistry of Brunner Coal Measure AMD such as mine type, hydrogeology, geology, geochemistry and climate is in progress. Minerals that control the concentration of aluminium downstream of AMD point sources include alunite, jurbanite and various forms of Al(OH)3.

Jan 1, 2005

Electrochemical Behaviour of Massive Chaclopyrite Bioleached Electrodes in Presence of Acidithiobacillus ferrooxidans and Acidithiobacillus caldus In this work, the monitoring of bacterial and chemical dissolution of massive chaclopyrite was evaluated using cyclic voltammetry (CV); the mineral surface was examined using scanning electron microscopy (SEM) and the elements were examined by Energy Dispersive X-ray Analysis (EDAX). The electrolyte employed for the electrochemical tests was the medium used to bioleaching the electrodes (3.0 g/L (NH4)2+SO4, 0.5 g/L K2HPO4, 0.5 g/L MgSO4+7H2O and 0.1 g/L Ca(NO3)2).The results showed differences in voltagramms carried out by Acidithiobacillus ferrooxidans and Acidithiobacillus caldus: In bioleached electrodes tested in the presence of Acidithiobacillus ferrooxidans, the anodic and cathodic current signals were larger than with Acidithiobacillus caldus. The analysis of CV results allowed attributing the different peaks observed in both the direct and reverse potential scanning to the oxidation of chaclopyrite to a secondary copper mineral (bornite, chalcocite and covellite) and its reduction via different non stoichiometric copper sulphides intermediaries. Surface evidences were observed by SEM, and chemical elements evidences were also investigated by EDAX.

Sep 13, 2010

Drilling in the south of the Rapahoe Sector at Greymouth Coalfield has demonstrated the existence of thick coal seams in the upper Rewanui Member. Seam correlation is handicapped by complex lithostratigraphy and laterally variable geophysical log profiles. An integrated investigation of coal measure stratigraphy, coal petrology, and proximate analyses, suggests a feasible model whereby most of the major seam intersections belong to a single horizon. Coal properties vary laterally in response to original swamp conditions, which are believed to have ranged from well-drained to ponded. A new model of peat accumulation is proposed for the northern Rapahoe Sector, whereby Upper Rewanui peat accumulation occurred on a flood plain between the levees of a major south southwest-flowing fluvial system in the east and the toe of a western alluvial fan.

Jan 1, 1985

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By S Lloyd, J Chow, S Fitzpatrick, D Greenup

The Tropicana deposit was discovered in 2005 after AngloGold Ashanti followed up an unexplained gold-in-soil anomaly. Discovered in a remote, barely-explored area of Western Australia not previously thought prospective for gold, Tropicana is the most significant gold find in Australia for more than a decade. The new, large scale open pit gold mining operation will produce an annual production of around 330 000 to 400 000 oz over a ten year mine life mining around 60 Mt/a.Process plant construction started in early 2012 and is due to finish in the December 2013 quarter. The mining contract was awarded to Macmahon Holdings (Macmahon) and mining commenced in July 2012 using conventional drill and blast, truck and excavator open cut methods.As a construction and start-up project in a greenfields location, the establishment of mining activities at Tropicana Gold Mine (TGM) involves the implementation of technical and operational systems, including the mining contract. Some of these systems and likely challenges were identified during earlier studies, while others were not foreseen until they were encountered. Alternatively, the time frames around implementation change depending on the changing knowledge of the project and industry environment. These systems include those common to the industry and those specific to the operation and location.This paper examines the implementation and development of a number of the systems specific to the establishment of mining operations, including the history, process and some outcomes. Although expected to be discrete systems to implement, they become interdependent. This linkage between systems further offers challenges and opportunities for the continuous progress of each system and for TGM as a whole.CITATION:Chow, J, Fitzpatrick, S, Greenup, D and Lloyd, S, 2013. Tropicana Gold Mine - mitigating the challenges of a mining start-up, in Proceedings World Gold 2013 , pp 51-60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By H Rossiter, C Simpson, J Market, P Jeanneau

Downhole Assay tools are a geophysical method to collect an instigated response from the material surrounding a drill hole and deliver a multielement proxy-assay. They were first tested in the Pilbara at the turn of this century, however since 2011 they have seen a more focused testing and implementation regime with multiple companies across multiple Pilbara mine sites. The increase in the volume of data has led to advances in the measurements and significant improvements to the efficiency of the calibration process. Pulsed Fast and Thermal Neutron Activation Analysis (PFTNA) downhole assay tools collect gamma photon spectra which are characteristic of elemental signatures. One of the key components of the technique is calibrating the spectral signatures to lab assays. Each tool is slightly different due to the organic nature of the crystal detector and therefore responds slightly differently. Environment and hole conditions as well as ore characteristics are among other external influencing factors. Thus, a unique calibration is required for each tool. In addition, not all elements are measured directly, but some are actually characterised by proxy, meaning that if the signal-to-noise ratio for an element is small, it may be easier to identify the mineral or geology in which that element is found and thus infer the concentration of the element. These proxies may differ for each site or geology type within a site. There is a large advantage to build a unique calibration per tool at each site rather than a universal one to be used across the whole province. This then delivers the accuracy and precision of measurements that mining companies require for modern operations. Early work with the tool required several thousand metres of calibration data and several weeks of analysis to build each calibration. This process has now been streamlined to significantly reduce the amount of data required and the analysis time to make it much easier to introduce new tools to a site with an existing model or to create new models. This paper details the calibration process, illustrating the increasing accuracy of the models as training data are acquired as well as the methods for transferring a calibration from one tool to another.

Nov 8, 2021

By J P. Jona, S R. Poulson, C H. Gammons

Spatial and temporal trends in water chemistry in the acidic (pH ~2.6) Berkeley Pit lake, Butte, Montana, can be explained by a newly developed iron-cycling model. Key elements of this model include: subaqueous oxidation of pyrite and other metal sulfide minerals by dissolved ferric iron, producing Fe2+ as a by-product; re-oxidation of Fe2+ to Fe3+ in the epilimnion, assisted by A ferrooxidans; precipitation of secondary ferric minerals (schwertmannite, jarosite) in the epilimnion; and replenishment of the Fe3+ concentration of the hypolimnion by seasonal lake turnover and gravitational settling and re-dissolution of ferric precipitates. Pyrite oxidation rates were approximated by using published rate laws and information on the Fe3+ concentrations (~5 mmol) of the Berkeley Pit as a function of depth. The results indicate that subaqueous pyrite oxidation may be releasing as little as 6 + 106 or as much as 600 + 106 moles of H+ each year to the lake; the large range reflects uncertainty in calculation of the specific surface area of pyrite in the flooded pit. This helps to explain the observation that the pH and metal concentrations of the Berkeley Pit have not improved with time since mine flooding began in 1983. Vertical cycling of ferric iron in the pit lake permits pyrite oxidation to continue in deep water, even in the absence of dissolved oxygen. This hypothesis is supported by preliminary stable-isotope data.

Jan 1, 2003

Gold rush histories are usually written as though they were unique events in the development of a region or nation. While this is a valid way of looking at gold rushes, it is not the only way. This paper is a brief attempt to relate the West Coast rushes to a wider context. During the second half of the nineteenth century the lure of gold transformed the Pacific Rim. Gold rushes drew more than half a million Europeans and Americans to lands bordering the Pacific. By 1900 a chain of mining, industrial and urban centres ran from California to Alaska; from Ballarat to New Guinea, and on to Western Australia. The New Zealand rushes were a significant chapter in this story. People, cargo and information passed from rush to rush. Techniques learned on earlier goldfields were imported; those developed in New Zealand were, in turn, taken up elsewhere. Administrative systems and regulations developed in Australia were implemented in New Zealand, improved and passed on to Canada. This interconnectedness was so strong that gold-seekers thought of the mining regions as a distinct culture, 'the whole digging world'. Much can be made of the similarities shared by rushes. But comparison can also highlight the individuality of each rush. +The early days of the West Coast rushes were perhaps the strongest assertion of a diggers' culture. A brief period in which a remarkable orderliness was created through mateship, self-regulation, and the occasional threat of rough justice. The West Coast rushes were both a unique experience and an integral part of a process which transformed the Pacific Rim during the nineteenth century. Understanding their part in that bigger story highlights just how unique they were.

Jan 1, 1996

The main factors which influence disposal of mine waste under New Zealand conditions are identified and discussed: namely, geological conditions which produce soft weather-sensitive waste, wet and cold winters which affect productivity in such waste, elevated seismicity which affects stability and the need for water rights which involve public participation. The waste disposal scheme for the Martha Hill Project is described, thereby illustrating how these factors influence the planning of a current mine strippings and tailings disposal scheme.

Jan 1, 1986

By J K. Claflin, S R. La Brooy, A M. Claflin

Rotary kilns have been in service in the gold industry to regenerate carbon for 65 years. At the time oxide ores with gold head grades of 8 to 10 g/t were being treated. Carbon could be regenerated adequately at 650°C and solution losses were less than 1%. Forty years ago, research indicated that heavily fouled carbon from flotation circuits had to be held at 750 to 850°C for ten to twenty minutes for full reactivation (Avraamides and La Brooy, 1987), gold head grades were typically 5 g/t and solution losses typically 0.02 ppm – still less than 1%. In 2017 it was determined (Claflin et al., 2017) that a residence time of less than 1 minute at 750°C can be adequate to reactivate carbon fouled with organics sufficiently to achieve 0.005 ppm solution losses in a flotation tailings leach plant.With the potential for discovery head grades to drop below 0.6 g/t, solution losses of 0.02 ppm represent over 3% loss. Tight operation of the whole carbon circuit is required to keep gold solution losses below 1% going forward.There are alternatives to a rotary carbon kiln, e.g. vertical kilns of which the Minfurn, Rintoul and Combustion Air kilns are examples. The alternative kilns can be heated using electrical heating elements, induction, and microwave. These kilns can operate successfully under the right conditions, however, they are almost exclusively for small carbon throughputs and are not suitable for the large carbon advance rates that are required to process low head grade ore deposits. Large throughput carbon kilns are are almost exclusively fossil fuel fired rotary kilns and the subject of this paper. In the view of the principal author, a fossil fuel fired vertical carbon kiln is preferred to a rotary kiln, however, it is not currently used in the industry.Thermal regeneration of activated carbon has a major impact on gold recovery in the carbon circuit. The carbon kiln and associated equipment constitute 3 to 5% of the capital cost for an oxide processing plant and up to 10% of the capital cost if flotation tails are leached. Despite the capital cost and impact on recovery, the carbon kiln is often poorly selected, operated and maintained.Six years ago Ausenco embarked on the Carbon Kiln Initiative to reduce solution gold losses. This body of knowledge has been published in a series of papers culminating in this paper on how to:1. Select a kiln appropriate for the flowsheet;2. Maintain the kiln to achieve design operation; and3. Operate the kiln to minimise costs and maximise reactivation.CITATION:Claflin, J K, La Brooy, S R and Claflin, A M, 2018. Carbon kiln selection, operation and maintenance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 251–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Harding, S Munro, R A. Bearman

Despite the importance of the primary crushing stage, performance optimisation is not well analysed with sufficient focus to give improvement opportunities. At the Newcrest owned Telfer operation, liner life plays an important part in scheduling planned maintenance. Major consideration is given to monitoring crusher performance, as the highly abrasive nature of the feed significantly impacts the liner wear life. A study was undertaken by the lead author which focused on establishing a strong baseline of accurate data pertaining to the performance of the crusher, in terms of, operating parameters, liner life and key machine design factors. As part of the study, mining feed materials were examined for a particular set of liners and this revealed that improved methods should be pursued. Due to the competitive nature of the mining industry, the business solution to complex problems with long shutdown cycles should be streamlined to incorporate a non-operational modelling approach that is significantly more efficient than traditional online trial and error methods. In order to dramatically reduce the time and business risks, it was decided to engage services to model and simulate the liner life by varying main operational and mechanical factors. The key to all simulation work is gathering high quality baseline data. Such data allowed deployment of the Kinematic Crusher Model and validation of the model against worn 2D wear liner profiles. The proven model was then successfully deployed to predict operational values that defined crusher performance. To enhance the study, further investigation into a set of mechanical and operational simulations generated a sensitivity matrix measuring key performance parameters throughout the wear life of the liners. The study revealed throughput as a highly sensitive parameter and a change in eccentric throw provided the greatest improvement in extending liner wear life.

Aug 24, 2022

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Caron, M Athayde, F Lavoie, R Joyce

Decarbonisation has become a major challenge for the global steelmaking industry, turning towards new technologies aimed at carbon footprint reduction, which on its own accounts for approximately 9 per cent global emissions. The iron and steel industry represents a ‘hard to abate’ sector, where much of efforts are currently being deployed into initiatives aiming to decarbonise the ironmaking through the use of green hydrogen, carbon capture utilisation and storage and state-of-the-art operation of current technologies, while little efforts being deployed to find carbon-efficient solution to iron ore burden preparation, where high-grade iron concentrate will increase in importance to ironmaking regardless of the chosen reduction route. Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), produces high-grade hematite concentrate with one of the lowest carbon global footprints. Still, QIO is partnering with its clients to the development of burden solutions to minimise CO2 emission, in the seek for a decarbonised steel. In a strong technological partnership, Binding Solutions Limited (BSL) has developed a novel, coldbinding technology to provide a cleaner, more cost-effective alternative to induration. The technology allows miners and steel producers to reduce Capex significantly and reduce energy consumption and CO2 emissions by 90 per cent. QIO and BSL have partnered to adapt the disruptive cold binding technology developed by BSL to QIO’s concentrate to produce a high-quality low emissions iron ore agglomerate. This paper describes the efforts taken to further develop BSL’s cold binding technology and its application to QIO’s high-grade iron ore concentrate to produce a hematite cold bonded briquette (hCBB) showing comparable performances with high quality seaborne fired pellets.

Nov 8, 2021

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The Black Star lead and zinc ore-bodies, situated in the western zone of mineralisation at Mount Isa occupy an area 2000 ft. long with varying widths from 100 ft. to 300 ft. The strike is N5°W, and the average dip 60° West.To test at depth the potentialities of this area, an extensive diamond drilling campaign was commenced on 16th October 1927. It was continued, with from one to six machines working, until the end of 1931. During this period, 26 inclined holes, with an average depth of 1224 ft, and a total footage of 31,828 ft. were completed. A vertical hole, 2452 ft. deep, for comparative purposes, has been omitted.These drilling operations came directly under the charge of G J Gray, General Superintendent of Mount Isa Mines, and, in the early stages were supervised by E. D. McDermott, of the Mining Trust, London. The foremen, who were in charge of various sections of the drilling operations, were: H Vale, F Bray, J Winston and A A Sanstedt.

Jan 1, 1932