Search Documents

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By René de Batz

From 1754 to the end of 1895 the production of gold in Russia had been approximately as follows: Kilogrammes. Russia proper (Finland and the Caucasus),. .. 890 The Ural Region,........505,386 Western Siberia,........116,937 Eastern Siberia,........1,218,372 Total,.........1,841,085 of the value of more than $1,200,000,000.

Jan 1, 1899

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Raymond F. Gray, Victor J. Hoffman, Richard J. Bagan, Harold L. McKinley

The first indication of tungsten in the Bishop area was the discovery of scheelite concentrations in a gold placer operation in the ( since named) Tungsten Hills in 1913. After early intermittent production, the deposits of the district were slowly discovered and developed. The Pine Creek mine, located in 1916 and under the direction of Union Carbide Corporation since 1935, became the principal producer in the district. By the end of 1965, the total production of the district had reached 3,450,932 units of WO3, 17,071,242 pounds of molybdenum, and 19,599,110 pounds of copper. The topography of the district is characterized by its extreme relief, ranging in elevation from 13,986 feet to about 4400 feet in the Mount Tom quadrangle. The present topography is the result of the uplift and erosion of the Sierra Nevada and the great subsidence of the Owens Valley with its related deposition and volcanism. The general structure of the pre-Tertiary rocks consists of a series of tightly-folded metasedimentary and metavolcanic rock remnants surrounded by exposed plutons ranging in composition from hornblende gabbro to alaskite. The metasedimentary rocks consist of low- to intermediate-grade metamorphic equivalents of fine-grained sediments deposited during the Paleozoic era in a miogeosynclinal environment. Later volcanics were deposited in a eugeosyncline. The ore bodies in the Bishop district consist of scheelite-bearing tactite formed by the pyrometasomatic replacement* of calcareous sediments along the contact with an acidic granitic intrusive. A number of the metasedimentary remnants have had tungsten deposited along their edges.

Jan 1, 1968

By D. Geoffry Minnes

Nepheline syenite is a silica deficient crystalline rock consisting of albite and microcline feldspars and nepheline, together with varying but small amounts of mafic silicates and other accessory minerals. Nepheline-bearing rocks are widely distributed around the world but only in Canada, Norway, the Union of Soviet Socialist Republics, and the United States are deposits worked commercially. Because of its low melting point and fluxing ability, nepheline syenite was investigated in the early 1900s by many students of glass and ceramics. Although the nepheline syenite deposits in Methuen Township, Ont., Canada, were discovered as early as 1897 it wasn't until 1935 that the first mill was erected to produce nepheline syenite products. In Canada, nepheline syenite deposits are worked by Indusmin Ltd. and International Minerals and Chemical Corp. (Canada) Ltd. who have combined production capacity in excess of 1800 tpd. Between 1935 and 1972 seven million tons valued at $78 million were produced from the Methuen Township deposits. In Norway, the Norsk Nefelin Div. of Elkem Spigerverket has produced nepheline syenite from a deposit on Stjernoy Island in western Finnmark since early 1960. Between 1961 and 1972 the company produced 930,000 mt with an estimated value of $17 million. Nepheline syenite has been under investigation in the Union of Soviet Socialist Republics (USSR) since at least 1928. In 1951 the first commercial alumina works was brought on stream at Volkhov, near Leningrad, utilizing nepheline concentrates from the Kola peninsula as mill feed. Since then two others have been completed and more are planned. Large quantities of portland cement, sodium carbonate, and potassium carbonate are produced in conjunction with the alumina. In the United States, nepheline syenite has been produced for many years from deposits in central Arkansas by the Big Rock Stone and Materials Co. for construction aggregates and, since 1947, for roofing granules by the 3M Co. Chap. 16 on "Feldspar, Nepheline Syenite, and Aplite" in the 3rd ed. of Industrial Minerals and Rocks (Castle, and Gillson, 1960) and Nepheline Syenite Deposits of Southern Ontario (Hewitt, 1960) contain excellent accounts of earlier commercial development of nepheline syenite as a glass and ceramic material. Therefore this chapter deals mostly with the period since 1960 and with matters not previously reported in detail. An English monograph on Nepheline-Syenite and Phonolite (Allen et al., 1968) is a complete current survey of nepheline syenite which, with its very complete list of references. is an excellent source book. End Uses Nepheline syenite from the Canadian and Norwegian producers finds use primarily in the manufacture of glass and ceramics. One producer also makes several grades of nepheline syenite that are useful as extender pigments and fillers in paint, plastics, and rubber. In the Soviet Union nepheline is used in increasing quantities in the manufacture of alumina, alkali carbonates, and portland cement and to a lesser degree it is used in the manufacture of colored container glass.

Jan 1, 1975

Jan 1, 1966

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By Harvey T. Gracely, Mark J. Woodhull

DURING the past few years a marked refinement has taken place in the design of electric power shovels for the mining industry, increasing their digging ability and speed of operation without adding to their total weight. The increase in pay load has been accomplished by a more rigid engineering analysis of shovel design, involving the adoption of new special alloy steels, new sections, and new welding methods. Emphasis has been placed on lightness with increased strength, which is most clearly shown in the front-end equipment where dipper, handle and boom are new in design, material, and construction.

Jan 1, 1938

By Dunbar D. Scott

The development in the perfection of mine-surveying instruments has been by no means rapid, as it has depended somewhat on the details of construction borrowed from astronomical and geodetic theodolites, largely on the restrictions laid down by mining companies and the prejudices of mine managers themselves, but more than all on the methods used in conducting surveys and the importance attached thereto. Mine-surveying, in some form or other, has been practiced from the very earliest times; but it has never kept pace with the other branches of surveying, or even with the art of mining itself, and cannot be recognized as an exact science until shortly before the beginning of this century. The works of Hero of Alexandria, who lived in the second century B.C., are still extant, and contain descriptions of a rectangular sighting-instrument, which he invented and called a diopter. His improvement upon this simple construction, which possibly he devised for use in the Greek mines for rough leveling-purposes and for laying out any angle, must be considered, says Hübner," as the origin of the highly perfected theodolite of to-day. Whether this instrument came into general use during the first centuries of the Christian era, is not recorded; in fact, no writer undertakes to tell how mine-surveying was conducted until 1556, in which year Agricola expounds the principles of mining and metallurgy in his De Re Metallica, devoting the entire fifth chapter to the practice of mine-surveying (see Fig. 1). In mediæval times those who possessed any knowledge of engineering skill made strenuous effort to keep their art a secret, partly on account of the miners' proverbial conservatism and partly for their own personal aggrandizement, and were, in

Jan 1, 1899

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By Nathan C. Rockwood

WHILE mining engineers have been searching in far corners of the country and of the world for hidden wealth there has grown up around us in nearly every city great wealth-producing mines calling for the investment of hundreds of millions of dollars and yielding products now sold for over half a billion dollars yearly-largely unknown and almost wholly neglected by mining engineers. But this neglect is explainable and excusable. They are industries of very recent origin-practically the growth of the last 25 years. They are in a very large measure the result of tremendous developments in engineering construction and the rapidly expanding use of portland cement concrete for structures of every description. Concrete as a material of construction is going through an evolution very much as did cast iron and other metals used in engineering; and this phase of the industry should appeal to the imagination of metallurgical engineers. At first iron was iron-a material of uncertain properties, owing both to small differences in chemical composition and in methods of manufacture. By successive steps iron was studied and knowledge of its properties developed-the striking effects of very small percentages of other minerals and of various heat-treatments.

Jan 1, 1924

By Orlando E. Romig

As metals and alloys are composed of an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. Previous Work The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.' He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and 11, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He pre- pared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By Lewis M. Haupt

Discussion of the paper of Mr. Granger, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 25, January, 1909, pp. 1 to 37. LEWIS M. HAUPT, Philadelphia, Pa. (communication to the 'Secretary*) :-This subject is of great interest to me, and I am noting progress and conditions as a test of my own judgment in advocating what I believed to be the nearer, cheaper and better route at Nicaraugua. I have as yet learned nothing to change my views, or modify the convictions which led me to retire from the Commission; but that is not the issue to-day. Our government is committed to the Panama route, and is bound to " make good." There are many points presented by Mr. Granger which seem to me worthy of very serious consideration. But when all is said there remains the risk of seismic convulsions, to which either form of canal is subject; and I fail to see that the risk would be reduced by making the cut deeper, with greater surcharge of lateral pressure upon the side walls. A severe earthquake in the rainy season would doubtless close either type of canal. One of the arguments in favor of the Panama route most insisted on, was that Nature had provided good natural harbors at its termini. Recalling this, it has interested me to note that the cost of creating the necessary harbors is estimated at $27,000,000. Mr. Granger refers to this, and quotes the Board's report to the effect that, on the Atlantic side, it will require 5 miles of jetties to " make an excellent harbor out of a wretched one." The vulnerable part of Mr. Granger's paper seems to me to lie in the admission that the plant required is still in the embryonic stage, and that at least one machine should be built and tested " to demonstrate that the theoretical strains and forces work out in practice exactly as expected." This, how-

Jul 1, 1909

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By Thomas C. Wilder

Jan 1, 1965