Search Documents

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,'' while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

By Luther W. Lennox

The purpose of this article is not to compare one type of grinding machinery with another and to conclude from a series of tests that one particular machine is superior to all others. Neither is the reader asked to tire himself with the details of many tests to prove the statements herein made. The Chilean mill stands today almost an outcast from the milling world. It ranks with the applicant for a job who has been given a trial along with others and condemned because he was not able to perform the definite task assigned as well as the others, and was forever eliminated. The judges did not tarry long enough to try this aspirant in a field of a slightly different nature. Even though it has been condemned, the writer contends that the published records will indicate that the trials were never shifted into the field of greatest efficiency for the . Chilean mill. Those of us who cling to this outcast as a fine grinder in our milling operations do not wish, naturally, to be condemned also, with the machine, and yet we feel that we are classed as behind the times, at least in this phase of our milling judgment. Hence there is considerable personal feeling in our efforts. During the last few years there have been published several papers on the relative merits of the various grinding machines. In two of these articles a comparison was made between Chilean mills and cylindrical grinders. In each case the Chilean mill came out second best from about all standpoints. The outstanding feature in these comparisons would seem to be the decided attempt to keep all conditions the same, so that each machine could be judged on its merit. As Mr. David Cole states,1 "We are inclined to regard a direct comparison of grinders arranged side by side, and making a product that affords as nearly as possible the same screen measure, as the Supreme Court in these grinding matters." The writer agrees that this is the very best method for true comparison between machines. The results in the two detailed tests should give the relative merits of the two grinders in doing the work assigned. And they probably do. The conclusion drawn in each case was adverse to the Chilean mill as a fine-grinding machine. However, the duty placed upon the machines was that of converting material that had already been

Jan 1, 1920

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the, scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blast-furnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussion as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces, all of which is expensive. The high metal contents of the concentrates

Jan 1, 1929

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By Robert S. Moehlman

Is recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. Cost oF Drilling Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 30 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $I per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft.. as more time is consumed in pulling rods' 3. Cost of preparing drilling stations, getting air underground to stations? etc' 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary') and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945

By Karl Fetters, John Chipman

The relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steel-making processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the -subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of labora- tory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermo-dynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component svstem seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By Karl Fetters, John Chipman

The relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steel-making processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the -subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of labora- tory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermo-dynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component svstem seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By H. G. Warren, E. W. Hough

Correlation of interfacial tension of the methane-n-pentane and methane-n-decane systems was made by Hough and Stegemeier by the use of the Weinaug and Katz equation. The methane-n-heptane and ethylene-n-heptane systems were investigated by the authors. Additional systems taken from the literature were the me thane-propane system by Weinaug. and Katz, the methane-n-butane system by Pennington and Hough, and the n- butane -carbon dioxide system by Brauer and Hough. These systems were analyzed by the Weinaug-Katz equation and the Sugden equation on the IBM 1620 11 computer using a regression analysis program. Parachor and exponent values for each component and system were determined. The experimental work was close to the critical point of the light component in the n-butane-carbon dioxide and ethylene-n-heptane systems, between the critical points of the light and heavy components in the methane-n-pentane, methane-n-heptane and methane-n-decane systems, and close to the critical point of the heavy component in the methane-pmpane and methane-n-butane systems. An empirical formula was developed to find a value of the constant B in the Sugden equation for binary hydrocarbon systems from the parachor values of the two components. Interfacial tension for binary hydrocarbon systems was found to be a direct function of liquid-vapor phase density difference in the same manner as a single-component system. DISCUSSION Interfacial tension may be defined as the measure of the specific free surface energy between two phases having different compositions.1 The interfacial tension (IFT) for a binary system may be predicted for any temperature and pressure if the

Jan 1, 1967

By H. C. Theuerer

GeC14 may be purified by extraction with HCI and chlorine. The process is as effective for the removal of AsCI:, as the more cumbersome distillation methods usually used for this purpose. GERMANIUM for semiconductor use contains impurities at levels no higher than a few parts in ten million. Material of this quality is obtained from highly purified GeC1, by hydrolysis to the oxide and reduction of the oxide in hydrogen. When purifying GeCl,, AsC1, is the most difficult impurity to remove. This is usually accomplished by multiple distillation procedures.1-3 AsC1, may also be removed from GeC1, by extraction with HC1.1-4 Reducing the arsenic to low concentrations is not practicable, however, because of the large number of extractions needed. This paper discusses a new method for the removal of arsenic from GeC1, by extraction with HC1 and chlorine. The method is rapid, leads to little loss of germanium and is at least as efficient as the distillation procedures currently being used. Theory of Extraction Procedures In the simple extraction of GeC1, with HC1, the following reaction occurs ASCl8G8C1 D AsCl3rc1 at equilibrium CA/Cn= K, where K is the distribution coefficient, and C, and C,, are the molar concentrations of AsC13 in HC1 and GeCl,, respectively. The materials balance equation for this reaction is VACA + vncn = VnC,, where V, and Vn are the volumes of HC1 and GeCl4, respectively, and C, is the initial concentration of AsC13 in GeC1,. From this it can be shown that for multiple extractions where C,, is the concentration of AsC13 in GeC14 after n extractions, and r is the ratio of V, to V,,. It is assumed that r is maintained constant, that equilibrium is established during each extraction, and that K is independent of the AsCl3 concentration. By saturating the system with chlorine, the following reaction occurs in the aqueous phase AsCl3 + 4H2O + Cl2 D H5AsO4 + 5HC1 at equilibrium K' = ------------ ai - a4 h2u - aet2 where a is the activity of the various components. The effect of this reaction is to reduce the concentration of the AsC1, in the aqueous layer and, therefore, to promote further extraction of this component from the GeC1, layer. If the arsenic acid remains entirely in the aqueous phase, the net effect of this reaction is to promote the removal of arsenic from the GeC11. The materials balance equation for extraction with HC1 and chlorine with the foregoing reaction is, then, VaCC + VACA + VACn = VnCo where C,. is the molar concentration of H3AsO, in the HC1. With the added assumptions that the activities of AsC13 and H8ASO4 in the aqueous phase are equal to their molar concentrations, it can be shown that for n extractions Cn/Cu = (1/rkK + rK + 1) n where k - K1 a4h2o - acl2/aoncl. It can be seen by comparing Eqs. 1 and 2 that if k is large, the removal of AsC1, by HC1 extraction will be greatly improved by the addition of chlorine. Dilution of the HCI used in the extraction with chlorine would also favor the separation. This, however, would increase the loss of GeCl,, which is undesirable. Experimental Procedure Germanium prepared from oxide of semiconductor purity is n-type with resistivities greater than one ohm-cm. The resistivity is controlled by the donor concentration, which is —lo-: mol pct. Germanium prepared from material with added arsenic will have lower resistivity commensurate with the arsenic concentration. With such material, at arsenic concentrations above 10-1 mol pct the resistivity is controlled by the added arsenic, and effects due to other impurities initially in the oxide are negligible. In this investigation GeO, of semiconductor purity was converted to GeCl,, and -0.01 mol pct As was added. This material was used for the extraction experiments and the purification attained determined by a comparison of the resistivity data for samples of germanium prepared from the initial and purified GeC1,. A method for calculating the arsenic concentration from the resistivity data is discussed later. The details of the experimental procedures used are as follows: Two hundred and thirty cu cm GeC1, were prepared by the solution of GeO, in HC1, followed by

Jan 1, 1957

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0' + P" phases at 700' C for superconductmainly examined using replication electron microscopy. The ß' or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4'5 Theoretical6'7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß' + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

By E. S. Wheeler, M. W. Murphy

A LARGE part of the molybdenum produced in Colorado is converted and consumed in the Eastern States. As the raw materials and the power needed for the conversion of the Colorado concentrate are also accessible in the Eastern States, the conversion plant has been installed some 1500 miles east of where the ore is mined and milled. When concentrate was first produced at Climax in 1918, a custom smelter converted the product into ferromolybdenum. By 1924, the Company had decided to produce calcium molybdate and rented a building and installed equipment for that purpose at Langeloth, near Burgettstown, Pa., about thirty miles west of Pittsburgh. For the first few years the plant was a simple one of small capacity. A small hand-rabbled roaster was used, the product of which was made iota calcium molybdate by a conventional method; then an eight hearth mechanically rabbled roaster was installed to increase and speed up production. The output was considerably less than a million pounds of contained molybdenum annually until 1928, when a small part of the produc-

Jan 1, 1946

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By O. B. Buchlen, J. W. Smith

The Coal Research Bureau of the School of Mines at West Virginia University, using an experimental flotation cell designated an airlift-cyclone was able to obtain a clean coal product containing 7.64% ash with 94% yield and 97% coal recovery. This favorable performance was obtained with the experimental flotation cell operating as a simulated three-stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient operation on high density feed slurry, and absence of moving parts. The primary shortcoming of the experimental cell is its limited capacity. The Coal Research Bureau presently has under construction a larger unit which, it is hoped, will provide the capacity and quality to establish the airlift-cyclone as a commercially feasible unit. Froth flotation of fine coal is a practice which has only recently gained wide acceptance in this country. Various explanations can be put forth for this delayed acceptance of a very selective and efficient system of coal preparation. Among these reasons would be the advent of continuous mining machines resulting in the increased production of coal fines, the change in market patterns from domestic and rail consumers who did not want fines to a predominantly utility market which normally consumes fines, and also the imposition of legal restrictions in regard to stream pollution. However, the major detriment is probably the high cost involved both in installation and operation of the flo- tation unit and auxiliary systems. These facts assume greater emphasis when considering that froth flotation installations normally process a low quality feed product. A recent estimate' of installation costs including dryers, filters, and other auxiliary equipment for a flotation system was $5000 to $7000 per ton of capacity while the operating costs, exclusive of auxiliary equipment, were estimated at 10 to 306 per ton of feed. The Coal Research Bureau of the School of Mines at West Virginia University is currently developing a simplified froth flotation cell, designated an airlift-cyclone, which may provide considerable savings in capital and operating costs without sacrificing product quality or recovery. This experimental cell consists of three primary components: 1) a vertically mounted U-shaped pipe; 2) an air injector device; and 3) an integrally mounted cyclone-like unit (Fig. 1). A feed slurry is introduced at the top of one leg of the U-pipe while compressed air is injected near the base of the other leg. The air serves both to aerate the pulp and to cause it to flow upward into the base of the cyclone unit where the floated clean coal is separated from the reject material and unfloated coal which remains in slurry. The Coal Research Bureau's experimental airlift-cyclone is somewhat similar in principle to a flotation device developed by Russian engineers in the late 1950's. In tests upon a two-stage pilot-size device, the Russians obtained very favorable cleaning efficiencies.' However, later experience with production models demonstrated that rated capacities and acceptable product quality could not always be maintained.3 Because of these limitations, Russian engineers subsequently recommended that conventional, mechanical cells be used when cleaning difficult to float slurries. Engineers at the Coal Research Bureau felt that such a device utilizing the combined actions of a cyclone and a froth flotation machine offered numerous attractive features and merited investigation. Accordingly, a small capacity experimental airlift-cyclone was designed and, with the permission of the Christopher Coal Company Div. of Consolidation Coal Co., installed in Christopher's Humphrey preparation plant near Morgantown, West Virginia.

Jan 1, 1964

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By Stewart Murray, Philip Klapwijk

INTRODUCTION Forecasting commodity markets is like predicting winners in a horse race: to get the answers right, one needs both luck and judgement. Commodity analysts bear some resemblance to racing tipsters as they try to convince interested parties that they have an inside track on which metal is going to win the great minerals race of the 1990s. Commodity analysts share some features with the gentlemen of the turf: • They influence other people in how to spend risk capital, • They don't put their own money at risk, and • If their tips consistently fail to deliver, then they end up looking elsewhere for employment. In order to find winners we need to know about the kind of race we are in and the strengths and weaknesses of all the runners. Miners are not interested in a five furlong sprint: their race is a long distance affair -- after all, the lead-times between discovery and start-up generally approach a decade for mines that will provide the staying power which leaders require in this industry. We need to look at the environment in which our commodities will be competing: in racing parlance, the going. Our equivalent is the economic background: just as some horses are at a relative advantage when the going is soft, so some commodities will do better than others if economic growth is sluggish. If we are going to pick the winners for the late 1990s, and as an industry, make the right investment decisions, nothing is more important than being able to forecast (with at least a semblance of accuracy) how and where the world's economy is going to develop in the next decade. In addressing the question of whether minerals are going to be leaders in the 1990s, this paper considers the idea that it will increasingly be the world outside the industrialised OECD that will provide the incremental growth in demand for mineral products. Economic growth in the Developing World is fundamentally different from that in the OECD, and the pattern of demand for materials in relation to economic output is much more favourable than in the OECD. If we are to forecast the future, we need to be able to understand the past, both in the boom times of the so called Golden Sixties and in the lean years that followed them. This should help us to decide whether the future is going to be like one or other of these extremes or, on the other hand, a return to normality. Having forecast the going, we can look at individual competitors. • Which are best placed to take advantage of the economic, social and industrial trends that we can now dimly foresee? • Which can resist the continued onslaught of the new materials and technologies? • Which of them will best weather the economic storms (assuming that recessions have not yet been abolished)? If we can provide answers to these questions, we will be well on our way to picking winners, i.e., the metals and minerals that will reward their owners with growing demand, steady (and high) prices leading to profits beyond the dreams of avarice.

Jan 1, 1990

By Orville R. Lyons, A. C. Richardson

During the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for 9 screen-type dryers, 8 rotary-type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal-drying operations, (2) information about the inherent characteristics of the coals dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen-size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1949

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957