Search Documents

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By A. J. Boyer, T. R. Meadowcroft

An experimental determination has been made of the efject of surface diffusion on the vapor pressure obtained in a Kwudsen cell. The results show that a knife-edge orifice in a molybdenum lid may give erroneous results for the vapor pressure of silver. when a correction suggested by winterbottom and Hirth is made, the results become meaningful. Experimental work with cylindrical orifices in molyhdenz~m lids and knife-edge orifices in ceramic lids shows that good vapor-pressure results may he obtained when the orifice is designed so that ejfusion is the only significant source of weight loss. THE Knudsen effusion cell technique has been used by many investigators to study relative and absolute vapor pressures over metals and alloys at elevated temperatures. As a result of this interest, some theoretical studies have been made of geometric factors affecting effusion from the orifice of a Knudsen cell. A review of these studies has been made by Margrave.1 Recently, Winterbottom and Hirth2 have suggested that a physical effect, that of condensation, surface diffusion, and re-evaporation, may seriously affect Knudsen cell measurements, especially when a knife-edge orifice is used. Inasmuch as many of the present vapor-pressure data have been obtained using knife-edge orifices. it was felt that an experimental evaluation of the effect of surface diffusion on Knudsen cell measurements would be of value both in the design of the cell orifice and in establishing realistic estimates of the limits of error for existing data. The experimental program was in two sections. Firstly, measurements of the vapor pressure of silver were made in cells with cylindrical and conical orifices in which the surface-diffusion contribution to the weight loss should be negligible. These results were correlated with existing data to give a reliable measure of the real vapor pressure of silver. Secondly, measurements made using knife-edge orifices were corrected using the surface-diffusion theory of Winterbottom and Hirth2 and were then compared to the real values. The experimental arrangement is shown in Fig. 1. The balance was an Ainsworth RV-AU-1 automatic recording microbalance capable of measuring weight changes of ±0.02 mg on a total load of up to 100 g. The temperature was measured by an optical pyrometer signted on the bottom of the suspended crucible. The temperature readings were calibrated in a separate experiment in which pyrometer measurements were made while at the same time thermocouple readings were taken of the temperature at the inside top and bottom of the crucible. The range of reproducibility with this technique was ±4°C. A constant voltage source maintained a temperature of ±2°C at 1200°C over 10 hr. Silver of 99.99 pct purity was used in nonporous alumina crucibles. Lids of molybdenum, tantalum, or magnesia were cemented to the crucible using a sodium silicate cement. Table I shows the characteristics of the lids used. The vapor pressure is obtained using the basic Knudsen formula:

Jan 1, 1965

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

On August 22, 1966, just 20 months after writing sales agreements with Japanese steel mills, Hamersley Iron Pty Ltd made its first contractual shipment of 52,000 tons to Yawata Iron and Steel Co Ltd. As world news, the event was not spectacular. But to mining men it represented an astonishing achievement. Twenty months of feverish effort and the expenditure of more than $100 million had created a large open-pit iron ore mine, a crushing plant, storage and load-out facilities for sized ore, and a supporting township at Mt Tom Price; a 182-mile standard gauge railway; and port and loading facilities for a nominal loading capacity of 6000 tph as well as a port town, Dampier, on King Bay. The project was executed in the sparsely inhabited, arid, dissected-plateau country of the Hamersley Range in the northwest sector of Western Australia. Hamersley, 60% owned by Conzinc RioTinto of Australia Pty Ltd and 40% by Kaiser Steel Corp, holds sale contracts for ore and pellets valued at $770 million. The main contracts are with the Japanese, who are to be supplied with 65.5 million tons of ore during the 16 years from August 1966 to August 1982 and 18 million tons of pellets over a 10-yr period beginning in early 1968. Of lesser importance at this time, but presaging trends, are contracts for a total of nearly 1.5 million tons to be shipped to England and Western Europe during the years 1966-68. A pellet plant with a capacity of 2 million tpy is now under construction at Dampier and is to be on stream early next year. Another interesting project for which the plans are set, is a desalination plant for sea water to supply industrial requirements and potable water for the town of Dampier.

Jan 5, 1967

By C. R. Van Hise

[Concluding Contribution of Prof. Van Hise to the Discussion of his Paper, and Others on the Same General Subject, presented at the Washington Meeting, February, 1900 (see Trans., xxx., 27, 177, 323, 424, 5 S); also of the contributions of Vogt, De Launay, Beck, Lindgren, hemp, Rickard, Bain, Keyes, Collins and Adams, presented at the Richmond Meeting, February, 1901, and printed in the present volume.] IN June, 1900, shortly after my paper was published in the Transactions, I made a briefer statement* before the Western Society of Engineers covering the same `round, which, in certain respects, is somewhat of an improvement. For instance, instead of using the terms descending and ascending with reference to the waters resulting in the two concentrations, my modified statement is as follows " The first concentration of many ore-deposits is the work of a relatively deep water-circulation, while the reconcentration is the result of reactions upon an earlier concentration through the agency of a relatively shallow water-circulation. Commonly the deep water circulation is lacking in free oxygen, and contains reducing agents, and the shallow water contains free oxygen. The deep water is therefore a reducing, and the shallow water an oxidizing agent."† Of the papers upon ore-deposits which, in vol. xxx. of the Transactions, follow my own, or which were presented at the Richmond meeting, a considerable number are wholly confirmatory of the conclusions which I have presented. Among these are the Washington paper of Emmons upon the Secondary Enrichment of Ore-Deposits‡ and his discussion at Richmond of other papers,§ that of Weed upon the Enrichment of Gold and Silver Veins,[ ]the discussion of Emmons', and at Richmond of Weed's paper by Collinst and Prof. De Launay,† the paper of Lindgren on Metasomatic Processes in Fissure Veins,¶ that of-Rickard upon the Formation of Bonanzas in the Upper Portions of Gold Veins,** and the remarks of Bain upon the Mississippi Valley lead- and zinc-deposits.†† It is therefore un-

Jan 1, 1902

By Leonard Obert

The structural stability of any mine or under- ground opening in rock is dependent on the stress field, that is, the state of stress in rock before mining, the stress distribution in the rock created by the opening, and the in situ strength of the rock. In the past mine design problems have been considered by assuming that the stress field is due only to the weight of the overlying rock, the stress around the opening can be calculated from elastic theory using laboratory-determined elastic constants, and the in situ strength of the rock can be determined from laboratory tests on small specimens. Solutions to hypothetical problems using this procedure are given in a report by Obert, Duvall, and Merrill.' Because of the uncertainties of these assumptions, this method can give only a rough approximation to the solution of actual structural problems. Obviously, this approach to determining the stability of underground openings would be greatly improved if the rock stress could be measured in situ, and it is undoubtedly for this reason that in recent years many investigators have spent considerable effort on the development of procedures for measuring rock stress. In this report a method is described for determining in situ the absolute stress in rock. The method requires the measurement of the deformation of a borehole before and after the rock is stress-relieved. The magnitude and direction of the applied stresses are calculated from the borehole deformation and modulus of elasticity of the rock. Also, the results of absolute stress determination made in the walls and pillars of underground openings in five rock types are presented. From these results a number of conclusions are drawn regarding the accuracy and limitations of this method and the problem of stress measurements in general.

Jan 8, 1962

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By L. C. Morganroth

Magnesite both Massive and Crystalline MAGNESITES are. of two general classes-massive and crystalline. Massive magnesite occurs in serpentine, being formed by the breaking down or decay of serpentine-making minerals or rocks as olivine, etc. (All the magnesia contained by the olivine is not liberated, as a portion goes to make up the serpentine; the breaking up of this serpentine later forms more magnesite.) Serpentine in various stages of transformation is found in the vicinity of magnesite deposits. Massive magnesite is very widely distributed. It is found in Greece, . California, Africa, India, Australia, Mexico, South America, and deposits of varying sizes occur in several of the European countries. Those on the Island of Euboea, Greece, are probable the most important deposits of this character of magnesite. They have been worked for a number of years, the principal quarries or mines being 3 miles in the interior from the village of St. George. (St. George is on the west coast of the island, between the towns of Limni and Khalkis.) (Figs. 1 and 2). -The magnesite occurs in veins or lenses in serpentine. Some of these lenses are very large; one worked several years ago was approximately, 50 ft. in thickness, 75 to 100 ft. high and 300 ft. or more in length. The magnesite is pure white and makes a very prominent feature of the landscape. While massive magnesite is widely scattered over the world, many of the deposits are in veins too thin to work. The usual mode of occurrence is in the form of stock work, the deposits in Venezuela, Mexico, and many of those in California, being of this form. The veins vary in thickness from the thinness of paper up to several inches, running in all directions, occasionally leading to a mass or nucleus of some,size. The spaces between the veins are filled with a disintegrated serpentine in the form of sand. Several of the deposits in California would probably be workable, if they were more favorably situated with reference to transportation, but by far the majority of the deposits are too poor to work. At one deposit,

Jan 9, 1914

GWILLIAM H. CLAMER (Philadelphia, Pa.).-About 16,000 tons of tin is used annually in the production of white metals. The real reason for using the so-called genuine babbitt, which is a high-tin base babbitt, perhaps in the majority of cases, is that tin has always been. a high-priced metal and people naturally believe that what they pay a high price for must be good. Mr. Jones has shown that the common metal, lead, is a superior base for most purposes for Which babbitt metal is used. The addition of lead is often looked upon as adulterant to genuine babbitt, and specifications for this reason rigidly restrict the lead content. A sub-committee of the Society for Testing Materials, at the meeting in June, presented tentative specifications on babbitt metal, in which were included twelve formulas, containing from zero to: 20, per cent. of tin, and several containing from 65 and 92 per cent. Babbitts. containing

Jan 1, 1919

By John Chipman, Raymond L. Orr

Recently reported high -temperatlnre thermal data have been incorporated in a reuieu' of the therinody-r~ar,zic propesties of iron. The recent data permit mot corlsisterlt and reliuble choices to be made for many of the pvoperties, resnlling in bettev eslablished tabrtlations of the thermodynamic functions. Values of Cp, h°t- - H°298. s°t - S2sa, and (G°T -H298/T are tabulated for -the solid and liquid phases of iron in both stable and melastable regions. Consistency of the tabulations has been maintained to the precision necessr~vg to yield the Gibbs energy change belween the bcc (a, 8) and fcc (y) phases of iron at temperatures pertinenl to alloy studies. THE importance of the metal iron has stimulated many investigations of its thermodynamic properties at elevated temperatures. Reviews and summaries of the data have appeared from time to time. Among these the 1951 paper of Darken and smith' deserves highest recognition for the quality of its criticism and for the precision and thermodynamic consistency of its tabulations. These and the more recent table of Kaufman, Clougherty, and weiss2 reproduce the Gibbs energy of the (a, 6)--Y transformation with sufficient sensitivity for alloy studies. Other recent compilations of equal validity3-' make no attempt to do this. Since this Gibbs energy change is not greater than 22 cal per g-atom over the temperature range 1100° to 1800°K, it is obviously desirable to tabulate values of (G°t - H298)/T to four places of decimals even though the absolute accuracy would not warrant such precision. The necessity for reconsideration of the problem is emphasized by the recent publication of several important researches on the enthalpy and heat capacity of iron. The older work is well-covered in the reviews cited and will be mentioned here only when actually employed in the tabulations. GAMMA IRON Transition temperatures are taken from the selec -tions of Elliott and Gleiser,5 based on the work of Boulanger7 and earlier workers. For the a-y (A3) transition at 1184°K we retain the value 215 cal per g-atom adopted by Darken and smith.' It has received confirmation in the recent work of Dench and Kubaschewski,' and of Braun8 using adiabatic calori-metry, and of Wallace, Sidles, and Danielson10 using a pulse heating technique. The enthalpy data of Olette and ferrier" and of Anderson and Hultgren12 at higher and lower temperatures may be extended to 1184°K to give the following values which are adjusted to the required value of ? 1184 Ha,1184 Ha 298 = 8030 cal per g-atom [11 hr,1184-ha298 = 8245 cal per g-atom [2]

Jan 1, 1968

By Harlowe Hardinge

[Crushing Tests by Pressure and Impact (T.P. 1895, by F. C. BOND,, Min. Tech. Jan. 1946). Discussion by H. HARDINGE and the author 1 Pumping Sands, Slurries and Slimes and Installation and Performance of Sand Pumps (T.P. 2013, by W. B. STEPHENSON, Min. Tech., May 1946 and T.P. 1978, by C. G. SOUTHMAYD, Min. Tech., March 1946). Discussion by OSCAR LEE, G. J. HOLT, L. D. ANDERSON, and the author 2 Rapid Polarographic Method for Determination of Copper, Zinc and Lead in Flotation Tailings (T.P. 2010, by G. A. CROWE and W. T. BISHOP, Min. Tech., March 1946). Discussion by E. H. ROSE and the authors 4 Ball Wear and Functioning of the Ball Load in a Fine-grinding Ball Mill (T.P. 1984, by W. I. GARMS and J. L. STEVENS, Min. Tech., March 1946). Discussion by J. F. MYERS, E. W. DAVIS, F. M. JARDINE, H. HARDINGE, F. C. BOND and the authors 5 Correlation between Mineral Behavior in Cataphoresis and Flotation (T.P. 2005, by A. M. GAUDIN and S. C. SuN, Min. Tech., May 1946). Discussion by 0. C. RALSTON, G. L. SIMARD and D. J. SALLEY 7 Accident Experience in Milling (T.P. 1981, by J. F. MYERS and S. E. SHARP, Min. Tech., May 1946). Discussion by C. E. MCKNIGHT, C. H. BENEDICT, T. S. WILSON and S. POWER WARREN9 Mill Design for Labor Economy (T.P. 1997, by NORMAN WEISS, Min. Tech., May 1946). Discussion by R. S. HANDY and the author13] Crushing Tests by Pressure and Impact (0.C. Ralston presiding) HARLOWE HARDINGE.*-Has the impact method described in the paper been used to compare the resistance to reduction in size of various materials with actual operation results of mills in the field? Is this impact method a better index of the true resistance to grinding under actual field conditions than other methods the author has reported in the TRANSACTIONS? F. C. BOND (author's reply).-The impact crushing device was designed to measure relative resistance to crushing, or what may be called the crushability, and is not used for comparing the resistance to grinding, or grindability. The correlation between crushability and grindability of different materials is not at all close, since fractures, zones of weakness, and structural features of rock have a much greater effect upon the crushability than upon the grindability. We still depend upon our standard grindability tests for measuring resistance to grinding, and use the impact crushing tests only in relation to crusher installations. The impact crushing device has several advantages over the measurement of crushing strength in pounds per square inch as an index of crushing resistance.

Jan 1, 1946

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

Jan 1, 1891

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs' scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs' scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952