Search Documents

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By Irving B. Cadoff, Stojan M. Zalar

AgInTe2, CuInTe2, and all Proportions of CuxAg1-xInTe, forMed homogeneous single phase alloys after direct solidification from the nielt. X-ray analysis indicated a zinc-blel~de strzccture typical of the chalcopyrite compounds, and the electrical resistivity and Sccbeck coefficient values were in the semiconducting range. AuInTe, and AuxA4g,-, InTe, formed by what appeared to be a peritectic reaction (the thermal analysis curves showing more than one arrest) and were conseyue~ztly polyphase. Substitution of copper into AgIrzTe, resulted in a continuous transition in the room tenzperature Seebeck coefficient from the negative AgIzTe, to the positive CuInTe,. A zero coefficient was obtained at about Cuo.55 Ago.45 InTe, . The temperatzire variation was similar to that observed for the stoichiometric compounds, that zs, tendency towards "p" concEuction at elevated temperatures. The thernzoelectric figure of merit for the compo~uzds, as determined by the Putley -Harmnn method were in the range 10- to 10-7 "K-l; the thermal conductivities in the order of 0.15 cal per sec-cm-oK. INCREASED interest in semiconducting intermetallic substances is expanding much of recent research from simple binary compounds into polyatomic systems and solid solutions. Ternary compounds A' represent a covalent extension of the binary semiconductors Within the a tin isoelec-tronic series, Ag-Cd-In-Sn-Sb-Te-I, divalent cadmium atoms in CdTe are being substituted for by monovalent silver and trivalent indium atoms to form the compound AgInTe, . By cross-substitution with elements of other isoelectronic series, a great number of ternary compounds A 'B"'c? is possible. In all of them, however, a necessary though not sufficient condition for the covalent, semiconducting bond—that there be four sharing orbital electrons per atom—must be fulfilled. In AgInTe,, each silver or indium atom is tetrahedrally surrounded by four tellurium atoms, while each tellurium atom is co-valently bound to two silver and two indium atoms. Synthetic chalcopyrites A'B"'c~ were first recognized as potential semiconduct&rs by Goodman and Douglas.' Austin, Goodman, and Pengelly discuss preparation difficulties and some electronic measurements on AgInS, , AgInSe, CuInSe, , AgInTe, , and CuInTe,. Chalcopyrites A B c2v are mentioned in papers attempting to classify and predict semiconducting behavior of intermetallic compounds; on the basis of saturated tetrahedral sp3 bonds,3 by specific selection criteria,' and by crystallographic considerations."

Jan 1, 1962

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By J. C. Bowling

Factors governing the choice of building types, materials, and the details of construction for mineral processing plants in remote locations with cold climates are discussed. Alternative types of building insulation in common use are described and a comparison is made of their suitability under various conditions.

Jan 1, 1973

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments, and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union, and the United States are summarized Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1980

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914

By J. P. Murphy, T. E. Leontis

DURING the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,1 in his treatise on-magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 200 to 300°C. (68° to 572°F.) and the results of Vosskühler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Keil2 have also reported the creep properties of a forged magnesium-cerium-manganese alloy at 200° and 250°C. (392° and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554°F.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 percent Mn have been found on the German .BMW-801D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both .the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per, cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at elevated temperatures. The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The

Jan 1, 1946

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 9, 1979

By Thys B. Johnson

Traditional mine planning concepts are discussed and suggestions for improvement through use of the developed model are proposed. The approach developed in this paper allows optimal planning of the complete mining-concentrating-refining system over the entire planning horizon and permits the system to dictate how and when to process a block of material, i. e., a dynamic cutoff.

Jan 1, 1969

By A. G. Paithankar, G. B. Misra

Although certain physical mechanical properties of rocks have been claimed to give an estimate of penetration rate in percussive drilling, the authors' work shows that the correlation of penetration rate with individual rock properties is Poor. The authors have developed a good correlation between penetration rate and a set of rock properties but the relation is complex. Energy per unit volume has been used as a measure of penetration rate in percussive drilling by Hustrulid and Fairhurst; however, their test setup is large wing a full size drill bit. The authors determined the minimum energy for unit volume Ev min for any rock at the optimum index angle in a simple laboratory drop tester wing a sharp microbit with a tip angle of ll0°. This Ev min has been found to correlate well with penetration rate obtained in controlled laboratory drilling in different rocks for different stages of bit wear. A comprehensive relation has been developed between penetration rate and Ev min.

Jan 1, 1981

By Y. A. Chang

Phase relationships in the system Cr-Si have been established based on the melting point, X-ray, metallo-graphic, and DTA studies. The three intermediate phases, Cr3Si, Cr5Si,, and CrSi,, melt congruently at 177V ± I@,Cr3Si, 1680"i 20°, and 1490" *20°C, respectively, while the fourth intermediate phase CrSi, melts peritectically at 1413" i 5°C to Cr5Si3 and a melt containing 51 at. pct Si. The temperatures and compositions of the four eutectic isotherms occurring in this system are given below: DTA and metallographic evidences indicate that Cr5Si, undergoes a phase transformation at 1505" i20°C. The high-temperature form of this phase could not be retained by the quenching techniques used in this study. TECHNOLOGICAL interest in the developing of composite systems, consisting of Sic on the one hand as a fiber-reinforced material and metallic substances such as chromium, nickel, or Cr-Ni alloys as a binding agent on the other hand, stimulated the present investigation of phase relationships in the binary system Cr-Si. Earlier works concerning this system have been evaluated and summarized by ansen and Anderko.' Their phase diagram was based mainly on the works of Kieffer, Benesovsky, and schroth2 and Kurnakov.~ According to these authors, the three intermediate phases Cr3Si, CrSi, and CrSi, all melt congruently at approximately 1730°, 1600°, and 1550°C. However, they did not agree on the compositional stability of the fourth intermediate phase between Cr3Si and CrSi. Later Parthe, Nowotny, and schmid4 determined the structure of this phase to be tetragonal T-1 type using the single-crystal method, and concluded that this phase had a formula of Cr5Si3. Since the compilation of Hansen and Anderko,' a new phase diagram for the system Cr-Si has been proposed by Elliott5 based on the works of Goldschmidt and rand,' Guseva and ~vechkin,~ and Trusova, Kuzev, and Ormont8 and the earlier works quoted by Hansen and Anderko.' According to this proposed phase diagram, all four intermediate phases have large ranges of homogeneity and all melt congruently. More recently, Svechnikov, Kocherzhinskii, and yupkog studied the system Cr-Si by the DTA-method. According to their findings, the three intermediate phases, Cr3Si, Cr5Si3, and CrSi,, melt congruently at 1700°, 1720°, and 1475"C, respectively, while the fourth intermediate phase, CrSi, melts peritectically at 1475°C to Cr5Si3 and a melt containing 50 at. pct Si. The temperatures and compositions of the four eutectic isotherms were found to be: In view of the discrepancies existing in the literature concerning the system Cr-Si, it was decided to rein-vestigate the phase relationships in this system. EXPERIMENTAL a) Starting Materials. Chromium disilicide and chromium or silicon powders were used in the present study to prepare the melting point and DTA samples. CrSi, was obtained by directly reacting cold-pressed elemental powders in an atmosphere of Hz at a temperature of about 1250°C. Chromium powder, purchased from Stark Chemical Co., had the following impurities in ppm: Fe, 200; Mg, 1000; and 0, 250; while silicon powder, purchased from the Welded Carbide Co., had the following impurities in ppm: Ca, 700; and Fe, 3500. b) Melting-Point Determination and Differential Thermal Analysis. Cylindrical melting-point samples of approximately 13 mm in diam and 30 mm in length with a rectangular groove in the center were prepared by hot-pressing of well-mixed powder mixtures in graphite dies. Before the melting-point determination, the hot-pressed samples were ground on a sand paper to remove any minute surface contamination of graphite. A small hole of 1 mm in diam, drilled on the center portion of the samples, served as a blackbody cavity for the temperature measurements. DTA samples approximately 13 mm in diam and 15 mm in length were prepared in a manner similar to the melting-point samples. Melting points were determined using the Pirani technique under a helium atmosphere of 40 psi. The design, performance, and operation of this apparatus have been described in detail by Rudy and ~ro~ulski.'~ The temperature measurements were carried out with a calibrated disappearing-filament-type micro-pyrometer. The measured temperature was corrected for losses from the quartz window of the melting-point furnace and for deviations from blackbody conditions of the observation hole. The procedure for temperature correction has also been previously described." The DTA method of Heetderks, Rudy and Eckertl' was also used to check any phase transformations of selected alloys in the system Cr-Si. It was not possible to make remated runs on the same sample once melt-

Jan 1, 1969

Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'3S) Min. Engr., Dir., Bu¬ reau of Mines. Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch, Morenci. Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Ten¬nessee Coal Iron & R.R.. Co., 1542 Brown -Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Command¬ing, Officer, Pittsburgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D., (M'32) Alin. Engr.. Div. of Cor¬porations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur, Ga. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co., Led., Vatnkoula, Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Bans. Abernathy, Jack H., (M'40) Peer. Engr., c/o Superior Oil Corp., National Bank of Tulsa Bldg., Tulsa, Okla. Aborn, Robert H., (M'10) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'39) Peer. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles, Calif. Abramowitz, William L., (J'40) Chem., Industrial Inventions, Inc., 103 Foster Se., Peabody, Mass.

Jan 1, 1942

By Roy J. Greenfield, Charles H. Stoyer

A geophysical survey was made in Kylertown, Pa., in an area where the ground water is polluted with acid mine drainage. Since acid mine water is a good electrical conductor, both direct-current electrical and electromagnetic loop methods were examined for their ability to determine the subsurface electrical conductivity structure and from this to imply the location of the acid water. Consistent results were obtained with the two methods and the interpreted subsurface resistivities were consistent with the electrical resistivity measured for water samples. It was demonstrated that fracture traces which act as conduits for ground water flow can be located with electromagnetic surveying methods. Thus geophysical methods for measuring subsurface electtrical resistivity can be used to advantage for monitoring the environmental impact on the ground-water system of acid mine water.

Jan 1, 1977