Search Documents

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By W. H. Emmons

This paper is the second of a series treating the relations of ores of the metals to igneous rocks. In the first paper1 the general problem was outlined and the normal downward changes in metalliferous lodes were briefly stated, with references to earlier papers treating the relations of ores to depths of their formation. The present paper by a number of examples illustrates the relations treated in the first paper. These examples are chosen chiefly from the larger mining districts because their underground developments are more extensive, but the same relations are shown in maps of scores of undeveloped areas in which the main geological conditions are nearly similar. Ecology of Metalliferous Deposits Ore deposits are divided into three groups: 1, Those formed by sedimentary processes; 2, those deposited by meteoric waters; and, 3, those formed in connection with igneous processes. The last group is the most important. It includes the magmatic segregations, which are igneous rocks in the strict sense, and the veins and related deposits, which were formed by precipitation in channels from solutions originating in cooling intrusives. These deposits may be divided into two groups: 1. Those related to intrusives as basic as diorite; and, 2, those related to intrusives more acid than diorite. The second group probably includes more than 95 per cent. of all lode ores. Nearly all of the ores of this group are associated with granitic batholiths or are in positions where it is reasonable to suppose that such a batholith, not yet exposed by erosion, underlies the area containing the deposits. The batholiths are great masses of deep-seated igneous rocks. When they are intruded most of them are probably as basic as diorite and some

Jan 1, 1927

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By H. S. Kalish, F. J. Dunkerley

INTRODUCTION AND PREVIOUS WORK THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low temperature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pct lead were measured at eleven temperatures from -196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the 'extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature mbrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. Cohen and van Lieshout1 have established the beta to alpha tin transformation at 13.2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin-rich phase will occur in a short-time tensile test. Polanyi and Schmid2 studied the tensile . properties of tin single crystals at -185°C and report that tin is brittle at-this temperature. In 1946, Kostenets3 reported that pure tin was brittle at -196 and -253°C, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pct lead at -253, -196 and +17°C. The ultimate tensile strength increased more than two times in going from room temperature to -196°C and about three times that value on further cooling to -253°C. All the alloys were brittle at -6°C except those containing more than 75 pct lead. Even at -253°C, the 75 pct lead alloy retained 36 pct elonga¬tion in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1948

By Arne F. Westgren

X-ray analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations. Changes in Solubility 1. Determinations of solubility limits in the solid state which show decreasing solubility with falling temperature are made as follows: A series of alloys extending into the heterogeneous region is prepared and quenched fromas high a temperature as possible, whereupon their lattice parameters are determined. Then one or more alloys are quenched from temperatures at which they are heterogeneous and their lattice parameters likwwise determined. For the purpose of determining the parameter the apparatus shown in Fig. 1 has been very useful for it produces sharp films in a short time which can be accurately read. High-order reflections (interferences) from the object are recorded on a film which is placed exactly perpendicular to the X-ray beam. The specimen usually has the shape of a small round bar.l Fig. 2 shows a selection of such exposures of silver-rich Cu-Ag alloys, and Fig. 3 gives the measurements made from these films. Fig. 4 gives the solubility curve which results.2 This curve is shifted to lower concentrations than the curve that is obtained from metallographic or physical methods. The X-ray method unquestionably gives more reliable data

Jan 1, 1931

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916

By K. H. Kilgren

At high formation pressures the distillate produced from a gas-condensate reservoir may be black in color. In this event the dense gas phase existing above the dew point is correspondingly dark. Volumetric phase data and an analysis of a reservoir fluid exhibiting these characteristics, together with a description of the visual equilibrium cell in which these observations were made, are presented in this paper. INTRODUCTION Previously the author, like many others in the oil and gas industry perhaps, tacitly assumed that the expressions black or dark oil system, crude oil system and bubble-point system were synonymous. Crude oil reservoir fluids are bubble-point systems and yield a black or dark stock-tank oil of relatively low API gravity. Conversely, a clear or amber colored trap distillate of high API gravity is assumed indicative of a dew point system or a gas-condensate reservoir fluid. This broad classification appears satisfactory for shallow reservoirs, but as the following study demonstrates, may be misleading when applied to deep reservoirs. Theoretically, there is no reason to exclude the possibility of producing a dark, low-gravity distillate from a gas-condensate reservoir. At sufficiently high values of pressure and temperature, heavy, dark-colored hydrocarbons may exist in the vapor state of a multi-component system. If enough dark-colored components are present in the reservoir vapor phase, the resulting condensate will be dark. The reservoir fluid investigated in the present study supports this contention. Stock-tank production was black in color and measured 29" APT gravity. From outward appearances, the liquid closely resembled a medium gravity crude oil. Experimental measurements proved the reservoir fluid was in reality a gas-condensate system. Volumetric phase data for this high-pressure system and a description of the visual cell in which the study was conducted successfully are presented in this paper. THEORY Phase behavior of a reservoir fluid can be predicted accurately with reference to a pressure-temperature phase diagram. If the reservoir temperature is lower than the critical temperature of the hydrocarbon fluid in place, bubble-point behavior will be observed. If the reservoir temperature lies between the critical and cricondentherm temperature, dew point behavior and retrograde condensation will occur. For reservoir temperatures above the cri- condentherm, only a single gas phase can exist in the reservoir regardless of pressure. Providing the composition of the reservoir fluid were known, it would be possible to predict the critical temperature and estimate the phase behavior from equilibrium relationships. However, the usual practice is to obtain a sample of reservoir fluid, subject it to varying pressures at the reservoir temperature and observe the phase behavior experimentally. The latter method was used to obtain the data reported here. WELL AND TRAPPING INFORMATION A summary of pertinent data for the well from which the reservoir fluid was sampled is presented in Table 1. This well is located offshore Louisiana. Except for the pressure which substantially exceeds hydrostatic pressure, the information does not appear unusual. Prior to the sampling program, the well was produced for 22 hours at a stock tank oil rate of 139 B/D. Average trapping conditions and gauging data for the six-hour test period that followed are summarized in Table 2. Samples of the first-stage trap gas and liquid were obtained during the latter portion of the test period. Ambient temperature remained 5 to 10F below trap temperature and presented no problem for sampling. Surface wind and moderate foaming of stock-tank oil presented some difficulty in obtaining accurate stock-tank gauges. SAMPLE ANALYSIS Compositions of the gas and liquid samples are shown in Table 3. The trap gas was analyzed by isothermal chromatography which revealed only a trace of heptane in the stream. The trap liquid was initially analyzed by low-temperature fractional distillation, yielding a bottom product of heptane and heavier components. Specific gravity of this fraction was measured and the mol weight was determined by freezing point depression. The hexane and lighter overhead gas collected during distillation was

Jan 1, 1967

By L. D. Mullins, W. R. Bartlett, R. H. Barham, W. L. Wahl

This paper describes an electrical model and its applicution to the analysis of four reservoirs in Saudi Arabia. The model has 2,501 mesh points and represents 35,000 sq miles of the Arab-D member. Details of modeling such as mesh size, control problems and standards of performance in matching reservoir history are discussed. The particular performance match achieved for the Arab-D rnember is presented. Details such as permeability barriers, aquifer depletion and iwerference between oil fields are given. The performance match realized in the Abqaiq pool is presented in detail. INTRODUCTION The resistor-capacitor network and associated control equipment described in this paper comprise an electrical analog of a reservoir system. Similar equipment has been used to study the transient response of reservoirs for many years. The unique feature of the model and application to be described is the extremely large size of the model and reservoir system, and the detail observed in simulating the reservoir with the model. The Arabian American Oil Co. first became interested in analog computers for simulation of oil reservoirs in 1949. Since that time, several models have been developed, each more elaborate and refined so that the reservoir system might be more closely simulated. The current model is the latest in a series designed, built and operated by the Field Research Laboratory of Socony Mobil Oil Co. in collaboration with Aramco. It has been and continues to be used to study the regional performance of the Arab-D member limestone reservoir. The Arab-D member is one of the Middle East's most prolific producing horizons.. THE MODEL The theory of simulating a reservoir system with an electrical system has been presented in the literature.1-5 Therefore, this paper will not discuss the theoretical aspect of the problem except to point out the correspondence between the fluid system and electrical system, as shown in Table 1. In general, the complete model is made up of input devices, output devices, central control and a resistance-capacitance (RC) network. At times, the RC network alone is referred to as the "model". However, it should be evident from the text which meaning is attached to the word "model". A discussion of the equipment follows. THE RESISTANCE-CAPACITANCE NETWORK The RC network consists of 2,501 capacitance decades interconnected through 4,900 resistance decades. The components are arranged to form a rectangular network of 2,501 mesh points in a 41- X 61-mesh array. Imposing the mesh grid system on the continuous reservoir system divides the reservoir into discrete areal segments. These discrete segments may be of various sizes. More precisely, the mesh size need not be uniform throughout the model. The RC network is fabricated in two sections which are connected at the top. An inside view of the "tunnel" formed by the two sections is shown in Fig. 1. The height and width of the tunnel are shown in the figure. Numerals appear along the bottom and along the back opening of the tunnel. These numbers denote the x and y co-ordinate positions of mesh points. Fig. 2 presents a rear view of one-half the model. The length dimensions of the model, as well as a rear view of the capacitor decades, are shown in this figure. The control dials used in adjusting the resistance and capacitance values on the model can be seen in the enlarged portion of the model shown in Fig. 3. The electrical capacity at any mesh point can range from 0 to 1.0 microfarads set to the nearest tenth of a microfarad. The electric resistance connecting any two mesh points can range from 0 to 9,990,000 ohms set to the nearest 1,000 ohms. External capacitors may be added to any or all mesh points if the need arises. The values of electrical resistance and capacitance are adjusted manually by manipulating the two types of decade units. INPUT EQUIPMENT A considerable quantity of equipment is used to control the input to the RC network. These input devices are

Nationalization of the coal mining industry in Great Britain was one of the first pieces of major legislation enacted by the post-war Labor Government in 1964. It followed a long period of economic depression with high unemployment and bad industrial relations in the coal mining industry during the 1930's, and shortages of coal during the last war. Upon nationalization, the National Coal Board took over control of the industry in 1947 and so became the biggest single employer of labor in the western world. As well as the coal mines themselves, it assumed responsibility for a great variety of other assets including coke ovens, byproduct plants, land, houses, railways and shipping wharves.

Jan 6, 1964

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By C. H. Mathewson

(New York Meeting, February, 1916) DURING the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform conditions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,1 in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent. reduction of area by rolling

Jan 1, 1916

By Hermann Wedding

It is now fourteen years since we German ironmasters, in considerable number, visited the United States on the occasion of the Philadelphia Exposition, and found the iron metallurgy of this country, as must be frankly confessed, in an advanced stage of development not previously suspected by us. At that time the United States already occupied, as now, the second rank, with Germany in the third, the product of pig-iron for that year being, in Great Britain, 6550, in this country, 2093, and in Germany, 1850 kilotons.* This relative position has not been changed. The present annual product of the three countries is, in round numbers, Great Britain, 8380, the United States, 7790, and Germany, 4530 kilotons. But the proportion of the United States, which was, in 1876, but 15 per cent. of the world's product, has now advanced to 30 per cent. When we left America in 1876, it was not only with gratitude for cordial hospitality and for the liberality with which our professional colleagues here had opened to our inspection whatever was worthy of notice in our special field, but also with the conviction that we had collected a great treasure of new and interesting information which we could utilize for the benefit of our German Fatherland. Particularly the achievements of the never-to-be-forgotten Holley in the field of Bessemer practice, set us an inspiring example for imitation in our own country. As an expression of our thanks in more practical fashion, I attempt in this paper to sketch what we have done in Germany since

Jan 1, 1891

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By Tracy Jarrett

THE alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various ele¬ments upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency induction furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5° F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by ½ by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by ¼ by ¾ in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second series consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1939

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940