Search Documents

By Fred C., Bond

DETERMINATIONS of circulating load in a classifier operating in closed circuit with a grinding mill are usually made from screen analyses of the mill feed and classifier products. The percentage remaining on someone selected screen size must be used in the calculation, and, because of the wide variation in average particle size between the mill feed and classifier overflow, an accurate and representative result at the selected mesh is often difficult to obtain. To overcome this difficulty and reduce the time required in making the determination, I have devised a method which uses the liquid-solid relationship in the circuit rather than screen analyses. The quantities required for the calculation include only the usual dilution and feed tonnage measurements, which should be made regularly in the course of ordinary mill operation and, in addition, the amount of new water added to the classifier, or to the head of the mill with the new feed. If measurements are obtained on both of these quantities it is possible to check the calculated circulating load, and to calculate the percentage of moisture in the new feed to the mill; or, if the latter is known, to check the feed tonnage.

Jan 1, 1937

By R. M. Brick

Segregation can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-I2 per cent Si alloys. The phasial condition implicitly described above—solidification over a range of temperatures with a compositional difference between solid and liquid—is found in nearly all solid solutions or combinations of solid solutions and eutec-tics, Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually deter-minable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be described first because it is an essential part of the picture. Coring Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus I, 3, 7 and solidus 2, 5, 8, and where the vertical I, 4: 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. Ib) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1945

By N. A. Gokcen, S. Fujishiro

THE pressures of Mn(g) in equilibrium with Mn7C3 and graphite have been measured by McCabe and Hudson' and Butler, McCabe, and paxton2 by means of graphite, zirconia, and Ta-Mo Knudsen cells. The details of corrections in their measurements were somewhat different from those of the authors;3'4 hence, further independent results at higher temperatures seemed to be warranted. The stoichiom-etry of Mn7C3 in equilibrium with graphite and its stability up to the vicinity of 1373 °K have been satisfactorily established by Kuo and persson5 (See also Hansen and Anderko).' The method of investigation has been described elsewhere in detail.3'4 The carbide was prepared in the manner described by McCabe and Hudson. In order to avoid possible reactions with refractory oxides, only graphite cells were used for the effusion experiments. The authors' results are the runs M-1, M-2 and M-3 listed in Table I, together with those of McCabe and co-workers. The heat capacity, c;, of Mn7C3 is not known; therefore McCable et al. plotted their data as log P vs 1/T and the results were only expressed first' as, and later2 as logP=- -14220+6.06 without further thermodynamic calculations. However, it is possible to estimate closely the necessary heat capacity as follows: When H; - &98 of CrC, or MnO, is plotted vs x, corresponding to various compounds, with temperature as the parameter, it is seen that the relationship is represented by a line of very small curvature. This relationship is also followed by other compounds which do not exhibit solid state phase transformations. In view of the fact that chromium and manganese have the atomic numbers of 24 and 25 respectively, it is reasonable to assume that H; - H;ae vs x for MnC, follows the same type of lines as those for CrC, for which adequate data are available.7 Similar correlations appear to be valid for oxides of two neighboring metals for which reliable data are available. The procedure is thus to move the lines for CrC, vertically (parallel to the axis of HT - H298) until they coincide with the points for MnC1/3, the only carbide of manganese whose H; - HO298 has been

Jan 1, 1963

Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard expresses regret that I have not given more extracts " from the fresh leaves of nature's open book." The quotations used by me in argument were all from nature's open book, and by authorities recognized in the scientific world as being able to decipher nature's unwritten pages, if not lay bare her inmost secrets. The study of -nature should be preceded by a knowledge of her laws. Natural science is but the summary of the observations of the past or an organized and accurate knowledge of the order in which things have been observed to happen. One who ignores the 'knowledge of the past or despises that of the present and approaches nature's open book with a virgin mind but too often finds her

Jan 1, 1895

By E. C. van Reuth

FIFTY-three alloys have been examined in the Fe-W and Co-W alloy systems in an attempt to verify the finding of o phases in these systems as reported by Goldschmidt.' The alloys were examined metallographically and by X-ray diffraction. The 10-g specimens were made by powder metallurgy techniques. Very fine, high-purity powders were compressed in a double-acting die at 120,000 psi after hydrogen reduction. All compacts were then sintered for 200 hr at 950°C in a helium atmosphere. Metallographic investigation and X-ray diffraction proved this time to be sufficient to allow complete homogenization before the subsequent high-temperature anneal. Each specimen was then sealed into an evacuated silica capsule and annealed at 1400"or 1500 C (except two) for 25 hr. (The 60 pct Fe and 55 pct Co alloys taken to 1610"and 1680°C respectively were held at these temperatures for 1hr. However, since these structures were at equilibrium before the anneal, and in view of their resultant structures, it is assumed that they reached equilib-

Jan 1, 1960

By AIME AIME

THE coal classification session* on Monday morning, Feb. 17, was opened by a paper by M. R. Campbell, entitled "Natural Groups of Coal and Allied Fuels," in which he pointed out, by means of graphical presentation of selected proximate analyses of coal, that coals can be classified on the basis of their moisture content. He proposes four groups of coal, brown coal, hydrobituminous, bituminous, and anthracite, each subdivided into two or three sub-groups. In a written discussion of this G. H. Cady, of the Illinois Geological Survey, showed that there is, in general, a progressive decrease in the moisture of Illinois coals from north to south, and that it would be very difficult to draw any arbitrary line dividing the coals of the State into two groups on the basis of moisture content.

Jan 1, 1930

By John Birkinbine

This piece of Carpenter crucible steel has exhibited a tensile strength of 116,000 pounds per square inch, an elastic limit of 89,170 pounds, an elongation of 25 per cent., and a reduction in area of 42 per cent. The test-specimen had a length of 2 inches between fillets, and was an inch bar reduced to an area of 0.504 square inch. This unusual tensile strength was determined before the bar had been hardened so as to show the remarkably velvety fracture here exhibited; but a piece of the same, tested after hardening, is reported to have stood a stress of 214,000 pounds per square inch. Another test-piece is said to have shown 136,000 pounds tensile strength, 97,300 pounds elastic limit, 20 per cent. elongation in 2 inches, and 40 per cent. reduction of area. Mr. Carpenter claims that this steel, containing 2.27 per cent. chromium and 1.04 per cent. carbon, can be welded like iron, and has proved most desirable,for the highest class of die-steel.

Jan 1, 1895

By Harvey N. Davis

MUCH has been written and said during the last twenty years about the place of the engineer in modern life, about the fundamental role that he plays both in developing and in maintaining the material foundations of modern civilization, about the advantages, and also the dangers, of the machine age that he has inaugurated, about the Frankenstein problems that he has unconcernedly foisted upon a generation utterly unable to cope with them, and about the obligation that rests upon him to stop inventing machines and turn his almost legendary energy and skill to inventing institutions that will constitute a solution of the problems he has raised, and contrariwise about his utter inability to offer wise or useful counsel in fields outside the narrow boundaries of his technical training.

Jan 1, 1938

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

By AIME AIME

A REQUEST for information as to the details of activities of the Engineering Council was made by the Joint Conference Committee for the benefit of the new American Engineering Council. , This request was complied with, and the scheduled reply so succinctly sets forth the activities of the old Council as well as the scope of possible activities of ,the new Council, about whose efforts there has been much discussion, .that it' is given herewith in full, except the 'budget which is summarized.

Jan 1, 1920

By W. Rostoker, A. Siede

THE venerable problem of hydrogen embrittlement of ferritic iron lacks as yet a complete explanation. Possibly part of the difficulty has been the exclusive preoccupation with the total ductility prior to fracture. In the past few years it has been noted at least twice1,2 that hydrogen charged into iron has the ability to depress the upper yield point and, at room temperature, to eliminate completely the discontinuous yield phenomenon. Cracknell and Petchl rationalize that the depression of the yield stress is an example of the behavior of inhomogeneous stresses. Their explanation requires that microcracks exist in the annealed metal, and that hydrogen collect in these cavities under high hydrostatic pressure. The hydrostatic pressure of hydrogen generates localized tensile stresses in the iron which, with external loading, reach the critical stress for yield prematurely. The local plastic zones will spread across the specimen before the Lüders bands can be generated, and the yield-point elongation phenomenon is eliminated. This viewpoint will be discussed in succeeding paragraphs. Rogers,2 on the other hand, represents the depression of the initial flow stress as a result of the interaction of hydrogen with dislocations. He submits two alternative modes of interaction. In the

Jan 1, 1959

By T. M. Drown, P. W. Shimer

The precipitation of phosphoric with titanic acid, by boiling an iron solution which had been reduced to the ferrous condition by sulpharetted hydrogen or sulphurous acid, was first noticed by E. H. Bogardus in 1874.* Since that time, as far as we are aware, not much has been published on the relation of these two acids to each other, and to silicic acid, in the ordinary course of analysis of iron ores. The following investigation may perhaps aid in clewing up some of the obscure points in the analysis of titaniferous ores. THE DETERMINATION OF PHOSPHORUS. From two to five grams of the finely powdered ore are weighed into a beaker and treated with about 50 c.c. of hydrochloric acid (sp. gr. 1.12), evaporated to dryness, and heated ih an air-bath for

Jan 1, 1882

By Edmund C. Pechin

THE writer approaches this subject with a great deal of diffidence —first, because it is utterly impossible to treat it satisfactorily within the limits of a paper, and, secondly, because the larger development is of so comparatively a recent date as to make authoritative data on some interesting points unavailable. For over one hundred years small charcoal-fnrnaces have been in existence, at widely scattered points, making a few tons of iron daily, and then gradually increasing to a daily output of, say 10 to 12 tons, as the market widened. With the exhaustion of local supplies of wood, inaccessibility to market, and sharp competition, bringing lower prices, many were compelled from time to time to make temporary stops, and finally to cease altogether. During the first half of the century there were at different times in operation between 75 and 90 charcoal furnaces. The last Directory of the Iron and Steel Works of the United States (1890) gives 19 as the number of charcoal-stacks in Virginia. Of these several are cold, and, it is

Jan 1, 1891

By G. D. Cody, D. S. Beers, B. Abeles

The thermal diffusivity (thermal conductivity divided by specific heat) of Armco iron has been measured over the temperature range 30º to 1025ºC. The results are in good agreement with the thermal diffusivity computed from published values of thermal conductivity and specific heat, except near the Curie point and at the a to y phase transition, where the measured diffusivity undergoes rabid variations. The differences observed are ascribed to a rapid variation in the electronic thermal conductivity near the Curie point, and a decrease in the lattice thermal conductivity, at the a to ? phase transition. A major difficulty in measuring the thermal conductivity of materials at high temperatures is the determination and elimination of radiation losses. It has been shown, however, that in measuring thermal diffusivity D (thermal conductivity/specific heat) radiation losses can be taken into account exactly.' In order to test the performance of a newly designed apparatus for measuring thermal diffusivity of solids,' we measured Armco iron to an accuracy of 2 pct in the temperature range 30" to 1025°C. This material was selected since both the thermal conductivity,3'4 k, and specific heat,5 C, are known accurately in this temperature range and thus the measured values of D could be compared with D computed from the pub-

Jan 1, 1962

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By Arthur L. Walker

DURING my trip around the world last year, covering a total of 45,000 miles, I saw many things of especial interest from an engineering viewpoint. Sailing from New York, I went through the Panama Canal, down along the west coast of South America, then over the Peruvian and Bolivian Uplands; thence to the celebrated copper mines of Chile; across the Andes, to Buenos Aires, then to Rio Janeiro; across the Atlantic to Lisbon, Portugal; through Spain to the Rio Tinto mines; across southern Europe to Italy; thence to Alexandria and Cairo; up the Nile to Assouan, to Palestine through the Suez Canal, Red Sea and across to Bombay; up to the country of the Moghul Emperors; then to Calcutta, from which point I shipped to Singapore, as having crossed the Equator twice, I wished to shake hands with it again; thence to Shanghai and Pekin; up to the Great Wall of China, back to Nanking and up the Yangtse to Hankow; then back and eastward across the Pacific Ocean. The climatic changes were sudden and severe; there was winter where, for me, it should have been summer and vice versa. The weather man was very kind, however, and until I was near the Aleutian Islands there were only three rainy days in a total of 220.

Jan 1, 1924