Search Documents

By E. Maltby Shipp

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must he secured, but they do not agree as to how this can best be done.

Jan 3, 1917

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By F. R. Van Horn

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer&apos;s standpoint and that practically no consideration is given to the employee&apos;s point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must be secured, but they do not agree as to how this can best be done.

Jan 4, 1917

By Joseph C. Platt

IT is not the object of the present paper to give a description of the minerals found on Mine Hill, in Sussex County, N. J., nor even to touch upon all the forms of the ores named, but to place upon record and call to the attention of the Institute some interesting facts concerning them. In May, 1875, after the Dover meeting, some of the members visited this locality, and, no doubt, it is fresh in their memories, being one of the best known mineralogical points in our country. It will be only necessary to describe it very briefly. Mine Hill and Stirling Hill, in Sussex County, N. J., the former being at the village of Franklin Furnace, and the latter near Ogdensburg,-are the only localities in the State where zinc ores are found in workable quantities.* Mine Hill is the more northerly, and mineralogically differs from its neighbor, chiefly in having no hydrated ores to speak of, while at Stirling this deposit is considerable. At both points Franklinite, red oxide, and silicate of zinc occur in large quantities. Mine Hill lies on the east side of the Wallkill River, above which it rises to an extreme elevation of about 150 feet. On the summit the outcrop of the Franklinite vein appears, while the lowest worked points are perhaps 10 or 15 feet above the level of the stream. Corn¬mencing at the northern end, where the Hamburg Road crosses it, this outcrop runs along the northwestern brow of the hill a distance of about 2000 feet, in a general southwest direction, to a point where is a large, cavern-like opening, called the "Southwest Opening." " Double Rock," about the highest point on the hill, lies near the middle of this 2000 feet of outcrop, and over or near it passes a property line, to which allusion will hereafter be made. At the Southwest Opening the vein bends abruptly towards the east,-the angle between the two parts being perhaps 45°,-and this easterly branch continues some 700 feet. From the northern part of the Stirling Hill deposit to the southern part of the Mine Hill deposit is about two miles, and in this interval the vein carrying Franklinite * See New Jersey State Geology, 1868, p. 669.

Jan 1, 1877

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45&apos; to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot&apos;s reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By J. D. Meakin

J. D. Meakin (The Franklin Institute Laboratories)— In a recent paper Garofalo12 has shown that a number of experimental creep results can be represented by the empirical relation In this expression ? is the steady creep rate, s is the applied stress, and A is a constant at a given temperature; a and n are adjustable parameters. Garofalo has shown that Expression [6] approximates to a power function at low stresses and a simple exponential function at high stresses. Among the data used by Garofalo are the results we published for creep of copper." For these results we found that the best correlation was an exponential law with different parameters in the low-and high-stress region, respectively. That is, i = A exp qs where A and q have different values above and below a critical stress a,. In Ref. 13 are listed a variety of observations which support the proposal that different mechanisms are operative at stresses above and below a,, and it is not felt appropriate to repeat those observations here. The purpose of this note is to demonstrate that, although the representation used by Garofalo does fit the experimental data very well, this fit cannot be used to conclude that only one mechanism is rate-controlling. The argument is best made graphically and is illustrated in Fig. 9. The continuous curves 2 and 3 represent pairs of simple exponential functions which intersect at i = 10-5. The curve 2 closely resembles the copper results in that a change of slope of 2:1 occurs at i = 10-5; the two functions shown are in fact: e = 10-7 exp (1.150) and ? = 10-6&apos; exp (0.576s) For purposes of comparison, curve 3 represents two exponential functions with a change of exponent of 3:1 and curve 1 has the exponent 1.150 throughout. It is quite clear that a satisfactory straight-line fit is obtained on a Garofalo plot for all three curves. The curves represent processes which have either a single stress exponent or two ex- ponents in a ratio as high as 3:l. It must, therefore, be concluded that the ability to obtain a linear dependence between log i and log (sinh cyo) cannot be taken as evidence for a single activated process. In fact, to some extent the way the experimental points quoted by Garofalo lie about a best fit straight line on the log (sinh as) plot indicates that two processes are indeed occurring. This is seen in Figs. 7(c) and 8(c) of Ref. 12 where it is particularly evident that the experimental points deviate from the straight line in a manner similar to curves 2 and 3 of Fig. 9. It is, of course, recognized that the generally used exponential form is an approximation to the hyperbolic sine function which is not valid for exponents of less than 1.2, e.g., qs < 1.2. The only curve in Ref. 12 which is affected by this restriction is Fig. 6(b) where the deviation from a In ? vs s

Jan 1, 1964

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By Harvey S. Mudd

WHEN talking about Europe it is well to endeavor to keep politics and economics apart but they have become so intermingled in recent years that the discussion of one topic inevitably leads to the other. Economic influences formerly prevailed over politics but today national and international economies are governed by political forces. Commerce in raw materials, food, and manufactured products is now so restricted by governmental controls that the capacity of the world to produce and to consume, to exchange goods and to pay for them, cannot be gauged by the past or predicted by a multitude of experts. In prewar days there were some yardsticks but today there are none. Thus it is hazardous to make forecasts, for in all fields of human effort the world has been cast upon an uncharted sea.

Jan 1, 1947

By Franklin H. Sharp, Kenneth L. Clifford

During the last few years the New Lead Belt of Southeastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, MG. for about 35 miles. The ore occurs as replacement deposits in the Bonneterre lime- stone formation which is about 1000 ft below the surface. In most of the mines, enough water is produced to supply the milling requirements without any reuse. There are dry areas, however, and at least two mills must rely on water reclaimed from their tailings lake to augment the mine water. These mills have no choice but to utilize recycled mill water.

Jan 7, 1973

By J. W. Ristori, V. R. Garfias

ONE of the most serious problems now confronting Gel- many-and one that will affect Italy even more seriously if she goes to war against England and France -is that of supplying her navy, mechanized army, and air force as well as her industrial and other needs with the necessary and related products. This problem, serious even now, will become vital should hostilities on a large scale develop.

Jan 1, 1939

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray &apos;analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949