Search Documents

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested 'I'he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14' taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By Louis W. Huber

The Liberty tunnels extend through a very steep hill in Pittsburgh (locally called Mount Washington) for a distance of slightly over a mile. The two tunnels parallel each other and are 59 ft. apart, center to center (Fig. 1) They are for vehicular traffic, and in each there is ample space for two lines of vehicles. Northbound traffic, toward downtown Pitts- burgh, is confined to the east tunnel and southbound traffic to the west tunnel. The South Hills residential district is separated from downtown Pittsburgh by Mount Washington, a steeply rising escarpment south of and adjacent to the Monongahela River. The Mount Washington district immediately south of the Monongahela River has been reached, for many

Jan 1, 1927

By Granville S. Borden

TAXES in general are onerous and are not a pleas- ant subject for discourse. There are, however, some very cogent reasons why we should dedicate a part of our thoughts and services to the solution of our taxation problems: The happiness of every individual in the United States depends on the maintenance of a stable government. The collection of taxes is an indispensable function of a stable government, and the power to collect taxes depends in part on the question whether taxes are fair and equitable. As representatives of the mining industry it is our duty to .protect it from tax burdens that are discriminatory or- unjust, As citizens we find that taxation is incessantly endeavouring to unravel the knots in our purse-strings. Many members of the Institute may be consulted .by clients on taxation problems, especially the phases which re- late to depletion and valuation. It is the hope of the writer that the discussion of some of the current depletion and valuation problems will stimulate interest in the problems, and as a consequence of this new interest facts will be ventilated, opinions rendered and services performed, which will be a means of solving the problems to the satisfaction of all parties interested.

Jan 1, 1929

By Sir Albert E. Kitson

The manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In certain respects they have a strong resemblance to those of India and Brazil, as contrasted with those of Tertiary age in Georgia, but in this paper no careful comparison with them can be made. Viewed from the present condition of the manganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments. Youngest are the products of decay and degradation with the concentration of manganese oxide in the rocks of both groups. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate degree of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows, largely of basic types. This has been named the Birrim System. Its age is unknown, for no definite fossils have been discovered in it. Since these non-fossiliferous strata at many plaees are of a character which in many parts of the world are suitable for the preservation of fossils, and which contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim System have normally a northeast-southwest strike, and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed diagonally across their strike for upwards of 600 miles, to the extreme northwestern corner of the Northern Territories. Thence they probably extend much farther into French territory.

Jan 1, 1927

By H. A. Doerner

PROPOSALS to use hydrocarbon or natural gases for the reduction of zinc from oxide materials may be traced back through Patent Office files to the early years of the present century. Natural gas at rates cheap enough to compete with solid fuels has been available at or near one major zinc district for more than a decade. That the seemingly meritorious and economically interesting applications of these proposals have not devel-oped into workable processes for direct production of zinc by natural gas cannot be completely ascribed to the proverbial conservatism of the zinc industry. It is possible to produce spelter commercially in normal times from zinc oxide and carbonaceous reducing agents without having a very precise understanding of the chemistry of the process. The reduc-tion by hydrocarbons is not, however, in this class, and the technical complexity of this reduction metallurgy and chemistry prohibits solution of the inherent difficulties by the "hit and miss" methods that are some-times thought to be practical. In a thermodynamic study of the chemistry of zinc smelting, Maier1 made a preliminary study of the chemistry of the use of methane for reducing zinc oxide by thermodynamic means, pointing out that the following reactions, the limits of which could be theoretically predicted, were important: ZnO + CH4 = Zn(gas) + CO + 2H2 [1] CH4 = C -I- 2H2 [2] ZnO + CO = Zn(gas) + CO2 [3] ZnO + H2 = Zn(gas) + H2O [4] Other possible reactions, not discussed in the reference quoted, are: CO2 + CH4 = 2CO + 2H2 [5] H2O + CH4 = CO + 3H2 [6]

Jan 1, 1933

By E. C. Bain

THE more familiar compositions of iron-carbon-chromium1 and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallographic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By J. B. Knaebel, M. W. Von Bernewitz

OUTSTANDING FACTORS that have largely induced the current great interest in the reopening of old mines and the search for new deposits are the increased relative value of gold, the certainty of a market for it, and the decreased activity and poor profits in other lines of endeavor. It is easy to understand why a miner out of a job and unable to find any other means of livelihood would naturally take to the hills with his pan, pick, and shovel; but never before have inexperienced, would-be prospectors and placer miners materialized from the factories and farms, the haberdasheries, and the oil and gasoline supply stations, in such numbers as the last couple of years have witnessed, except when rich strikes of the proportions of a Klondike have been made. What, may one ask, has occasioned this condition? Unemployment has put these men in a receptive frame of mind, and newspaper and magazine articles have done the rest-- The Gold Miner of Los Angeles (a new weekly), The Mid- Week Pictorial (New York) for Sept. 3, 1932, and Popular Science Monthly for August, 1932, for instance. Even the Saturday Evening Post had an article on a promising part of Colorado. Stories that good wages may be had for the panning in nearly every western state have been featured by daily papers, popular "scientific" magazines, and quasi- technical journals. These tales have been eagerly grasped by thousands of people whose ignorance of mining has only served to increase their enthusiasm.

Jan 1, 1932

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen'l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O'C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen'l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the 'high' and 'low' circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887'0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937'0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By Walter McKee

WHEN mixed with common cast steel in quantities ranging from 11 to 13 ½ per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time. Manganese steel has been manufactured for about 26 years. .It was first made in a small way in England and subsequently produced in the United States in 1892. At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 lb. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13 ½ per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 5 ½ in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 5 ½ in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an

Jan 12, 1915

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934

By P. A. Beck, L. J. Demer

As reported in a previous publication,' isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

By Victor A. Phillips

A series of specimens of a Cu- 3.23 pct Co alloy were prepared with particle diameters from zero to 590A. The samples were then cold-rolled 95 pct and the effects of the particle size on the behavior on annealing for hr at temperatures between 100" and 900°C were studied (by hardness, light, and electron metallography). Particles, particularly for d r 105 to 590A, greatly impeded softening and vecvystallizn-tion, and tended to give elongated grains. Particles deformed fairly homogeneously with the ,matrix, be- IN a previous study by the author,' the growth of cobalt-rich precipitates was followed electron microscopically in Cu-3.12 Co alloy as a function of aging, typically at 650°C. The coherent spherical precipitates grew to 520 + lOOA average diam before spontaneously losing coherency and developing (111) facets. Stretching a few percent after precipitation 2aused loss of coherency to occur sooner at about 220A average particle diam. The particles apparently retained their fcc structure after loss of coherency. coming lau2ellae. For d = 55 to 180A, these lamellae gave streak-contrast effects apparently due to coherency strains , and spheroidized on annealing at 600" to 650°C, forming coherent particles. Particles of d = 250 ov 320A lost coherency during t-olling, giving incoherent lamellae. Recrystallization apparently occured by growth of new grains into unrecrystallized (recovered) material at temperatures below that at which cobalt atoms had much mobility. The present study was undertaken to explore the effect of cobalt-rjch particles of various average sizes from 50 to 600A diam on the isochronal annealing behavior of copper after heavy cold rolling. The previous work' was used as a guide in preparing the two-phase series of prerolling structures. The solution-treated alloy was also rolled for comparison. A further question of interest in the present study was whether dislocation and particle hardening were additive, since the prerolling structures covered the full range unaged - peak aged — overaged, and further precipitation might occur on annealing after cold rolling. Although there have been exhaustive studies of the isothermal2"6 and is~chronal annealing behavior of

Jan 1, 1967

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes hack well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948. Summary Of the eight million tons of coal mined in the two states in 1947. ap- proximately two million tons were washed in wet washing plants, using concentrating tables or jigs. The one table plant accounted for 70 pct of the output of washed coal, and two large Baum jig plants accounted for an additional 26 pct, leaving only a small residual tonnage to be accounted for by other types of jigs The necessity for washing coal is occasioned by the desire or necessity of reducing the ash content of the coals— sulphur is not a problem in this area. All washeries, except the table plant, are at or near the tipple, hence wash only one kind of coal. At the table plant a large number of different coals are washed. Only at the table plant is there any occasion for drying any considerable quantity of fine coal— other plants size and/or dewater on shaking screens. The results of washing at the smaller plants are judged by the number (or lack) of complaints about the quality of the washed coal. This is probably as good a system as can he devised for small, intermittent operations. The efficiency of the Baum jig ap-pears to be quite high. This is to be expected as long as the automatic control of the refuse gate operates properly. The efficiency of the concentrating table is not as high as that of the Baum jig, especially when the "difficulty" of washing is taken into consideration. When dealing with coals in which the "bone" is larger than the "coal," the table appears to be at a definite disadvantage, because of its sizing action.

Jan 1, 1950

By C. S. Anderson

Georgia, since 1829, has produced nearly $18,000,000 from her gold mines, but in late years the output has dwindled to insignificance. In view of present universal efforts to increase gold production, it seems pertinent to record some recent observations in that field, briefly review its past and weigh probabilities of reviving gold mining there. Little in this paper can be claimed as new or original, and it does not present results of a detailed or profound investigation of the whole region. The Allatoona gold mine was reopened in January, 1932, and explored at greater depth during the period from January to June of that year. A number of other abandoned mines were visited, but since the workings, in common with most such mines in Georgia, were flooded or caved, underground conditions could not be examined. For a wider knowledge of the subject, a search was made through available pertinent literature and statistics, a bibliography of which is appended hereto. To all the sources obligations are gratefully acknowledged. Production The discovery of gold in Georgia, in 1829, led to an influx of 6000 to 7000 miners and a production of over $200,000 in the following year. A branch of the United States Mint, established at Dahlonega in 1838, accounted for $6,115,569 up to the time of the Civil War. The output fluctuated greatly from year to year, with an all-time peak of $582,782 in 1843. In only one other year, 1845, was the half million mark exceeded. After the war mining began again, but 1883 is the last year for which an output of $200,000 is reported. Placers, always the main source of production, were yielding less and less, and in spite of increased quartz-mining activities the downward trend continued. The last year in which there was a production of $100,000 was 1902. In 1914, $16,270 came from 26 placers and 11 deep mines, with the latter reporting 1750 tons of $3 average value. In 1925, one placer and four lode mines that mined 8100 tons assaying $1.19 per ton produced $9500. One placer and one quartz mine, operating in 1930, reported a total output of $4194. Table 1 pictures the waning output.

Jan 1, 1934