Search Documents

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Hervé Thomasson

Siemens VAI has made an important Research & Development effort since 10 years on laser welder field. The last step of this program was in 2010, the evolution of its laser welder range by implementing the solid state technology with laser cutting and welding. Since this step, 8 welders were produced by Siemens VAI. Now after more than 1 year of industrial feedback, the results are showing a high level of performances on very demanding processing lines for a large range of products from Silicon steel to High Strength Steel with DP and TRIP grades. This laser welder concept using laser cutting and welding through solid state laser source is also proposed by Siemens VAI for pickling lines and tandem mills with significant advantages compared to standard solution.

Jul 30, 2018

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Hiroshi Ichikawa

In 2013, Nippon Steel & Sumikin Engineering Co., Ltd. (hereafter referred to as NSENGI), Tenova HYL and Danieli have entered into an agreement to combine ENERGION DR technology into blast furnace technology and/or with syngas technologies. This new alliance will allow the three companies to combine research and development activities with their respective expertise in ENERGIRON DR technology, Blast Furnace technology and Syngas (by-pro gas and coal gasification) technology, with the ultimate objective to develop breakthrough iron making technologies and create such EPC projects. This paper introduces the concepts and the features of our breakthrough technologies of combining of ENERGIRON DR technology, Blast Furnace technology and Syngas technology.

Aug 16, 2017

By Maycon Athayde

Samarco produces high quality iron ore pellets processed in straight grate furnaces. This process is essential in order to obtain adequate mechanical strength to the pellet transportation and operation in the reduction reactors. All mechanical properties of the agglomerates are obtained during the stage of firing where the slag and sintering bond happens, thus it is a decisive step to improve the pellet quality. Therefore, the velocity distribution of gas flow within this zone must have homogeneous and even velocity distribution. Hence, it was developed a mathematical CFD model to characterize the gas flow in the burning zone, applying the equations of conservation of momentum, mass and energy and an uneven flow distribution was identified and the gas velocity analyzed and validated through experimental data. On the other hand, on the present paper, an improved firing zone burner were developed and industrially implemented in a way to mitigate the uneven flow pattern detected aided by CFD. Different burner designs, based on CFD analysis, were experimented in order to succeed on the aggressive condition. The combustion was investigated and burner efficiency evaluated and compared with the simulation purposed.

Aug 2, 2018

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Rene Grabowski

Optimization of workflows and intelligent stock management; Slab stacking improvement by automated transport orders; and System automatically registers any slab movements even in manual operation. Case story: Steel producer ArcelorMittal Eisenhüttenstadt GmbH in Germany uses Primetals Technologie’s new stock yard logistics system in its finishing department. An exact image of its slab storage at any times is given by the warehouse logistics system to the company. It not only enhances the composition of the stacks of slabs, but also automates recording of manual restacking operations. Therefore the solution improves workflows and simplifies stock control. Cycle times have also been reduced due to the fact that the slabs can be charged to reheating furnaces ahead of the rolling mill due to less restacking operations within the slab storage. The expandable, modular system is based on the Siemens Simatic IT and Primetals Technologies’ IT4METALS Logistics product platform. It provides a large number of organizational and commercial features in the form of sophisticated graphics and tabular evaluations. For example, it can show how many crane movements have been made per shift for any category of slab, so that the time and cost for each operation can be calculated accurately.

Aug 16, 2017

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017

By Flávio Beneduce Neto

As trincas a quente ou de solidificação em peças micro-fundidas em superligas a base de níquel podem ser um item importante no índice de perdas em componentes específicos. O aparecimento desse defeito está ligado fundamentalmente à quantidade de líquido interdentrítico nos últimos estágios da solidificação e, principalmente, ligado à composição química desse líquido. Há duas ligas amplamente utilizadas na produção de rotores para turbo-compressores ou turbinas para a geração de energia: o Inconel 713C e o Inconel 713LC. A diferença entre estas duas ligas é essencialmente o teor de carbono. Curiosamente, a liga LC tem uma maior tendência ao aparecimento de trincas de solidificação. O presente trabalho procura identificar as diferenças de comportamento na solidificação dessas duas ligas através da termodinâmica computacional e ligar essas diferenças no aparecimento das trincas. Os resultados indicaram que os teores de Zr e Nb do líquido remanescente da solidificação são muito superiores na liga LC causados pelo atraso na precipitação dos carbonetos tipo MC nessa região que deve ser a fase que aumenta a resistência mecânica da área. O correto balanceamento da composição química da liga em relação aos elementos citados permitiu que o índice de perdas por trincas de solidificação caísse para níveis próximos a zero.

Aug 8, 2018