Search Documents

By Aliye Arabaci

In the present investigation, an attempt has been made to study the reduction behavior of composite pellets consisting two different types of iron oxide fines (high and low grade) and coke or lignite fines as reducing agents. The reduction experiments were carried out under isothermal conditions and constant flow of nitrogen gas in the temperature range of 900 ? 1100 oC. The variables investigated are the reduction temperature, Cfix/Fe3O4 ratio, reduction time and reductant type. In the experiments carried out with Sivas Divrigi A head magnetite ores (high grade) at a temperature of 1100 oC, for 40 minutes and on the condition that Cfix/Fe3O4 ratio is 0.2, in which lignite and coke fines were used as reductant, degree of reduction was obtained as 91 % and 86 %, respectively. Whereas, in the experiments realized with Malatya-Hekimhan-Hasançelebi magnetite ores (low grade) on the same conditions by using lignite as the reductant, around 60 % degree of reduction was found.

Jan 1, 2008

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By Xu Weihong

After being pre-treated, composite electro-deposits of semi-bright nickel/nano-SiO2 with bright nickel or with amorphous Ni-P alloy, and Composite electro-deposits of Zinc were prepared on Nd-Fe-B magnetic material. The effect of cathodic current density, nano-SiO2 concentration, stirring strength and surfactants on the corrosion resistance of electro-deposits were studied. In addition surface appearance and structure of the composite coatings were analyzed by SEM. The present investigation shows that the corrosion resistance of composite electro-deposits of semi-bright nickel/nano-SiO2 with amorphous Ni-P alloy was the best, the solution system of semi-bright nickel/nano-SiO2 with bright nickel was stable and its electro-deposits also had an excellent corrosion resistance, composite electro-deposits of Zinc not only had good corrosion resistance, but also low cost, thus making it an excellent electro-deposit for medium or low-class Nd-Fe-B magnetic material.

Jan 1, 2006

By Fangqing Yin, Qingyu Deng, Zhengfeng Qu, Mengjun Hu, Meilong Hu

Titanium bearing blast furnace slag, which contains 20%-30% TiO2, is a valuable secondary titanium resource. Based on the thermodynamics calculation effect of the temperature on the reduction of the slag in vacuum were studied at certain vacuum degrees. The results show that magnesium vapor and silicon monoxide vapor can be obtained at the condition of high temperature and low pressure. The purity of TiC increases with temperature increasing. When the temperature arrives at 1623K TiC can be obtained besides the reductant carbon. XRD result of the powder collected from the furnace cover show that magnesium and silicon in the titanium bearing BF slag leave the slag system during carbothermal reduction in vacuum. From the above it can be concluded that TiC can be obtained from the titanium bearing BF slag and silicon and titanium in the slag can be separated by carbothermal reduction in vacuum and acid leaching.

Jan 1, 2016

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By XUEWEN WANG, Bowen Li, Mingyu Wang

A novel technology characterized by higher extraction of vanadium and recovery of valuable elements was developed to recover vanadium from stone coal. The brief flow of the novel technology mainly includes low temperature sulphation roasting, water leaching, recovering potassium, aluminum, copper and selenium, solvent extraction enrichment vanadium, precipitation of red vanadium, removal sodium from red vanadium and calcinations. The total recovery of vanadium reached 76.3%, which was higher than the current applied technology. The novel technology was environmentally-friendly and could extract vanadium from the stone coal, in which the content of V2O5 was less than 0.8%.

Jan 1, 2015

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Thomas A. Post

The methodology of determining the optimum SX pumper-mixer system based on bench top, pilot, or small-scale solvent extraction systems, is demonstrated. The design of small-scale SX-plants is different than a full-scale plant. The difference is explained here. The use of dimensionless parameters Nh, Nq, and Np that describe the head, flow and power of the pumper is shown and how to use them for the scale-up. Additional data is required to determine the optimum operating range. Applications of this methodology were used to design well known currently operating SX plants. The emphasis on the optimization of hydraulic efficiency will be shown on examples, including how the hydraulic efficiency is affected when the throughput of the system goes beyond the design. Designs of all sizes of equipment will be shown which optimize the hydraulic efficiency.

Jan 1, 2003

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Lei Wang, Jianjun Wang, Lingen Luo, Zhengbang Li

Dearsenication in molten steel was studied by adding Ca-Fe Alloy-based arsenic removal agent. In order to improve the utilization rate of Calcium Iron Alloy and improve arsenic removal ratio, [O] is less than 0.0005% and [S] is less than 0.0035%, Al is added into the molten steel. In the processes of adding CaO-Al2O3 based alkalinity slag for arsenic removing in molten steel (initial arsenic content is 0.0080%), arsenic removal ratio reaches 50% when Ca-Fe Alloy addition amount is 18%. During the arsenic removal experiment, adding Rare Earth promotes the arsenic removal reaction and makes the arsenic removal more effectively.

Jan 1, 2015

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By C. M. F. Vieira

Crushed fired brick waste, known as grog, screened at two different particle size, 840 (20 mesh) and 180 µm (80 mesh), was used in mixtures with clayey body to make typical red ceramics for bricks. The effect of the grog addition up to 20 wt.% on the properties of bricks fired at 700oC was evaluated. The results indicated that both the particle size and the amount of grog addition changed the fired properties of the clayey body. Additions above 5 wt.% of grog, with a coarser particle size, decreased the mechanical strength of both the dry body and the fired ceramic pieces. By contrast, grog with a finer particle size may be used up to 10% wt. without deteriorate the properties and corresponding microstructure of the clayey body.

Jan 1, 2009

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By Masanori Harata

A fundamental study was conducted on a new process for producing scandium (Sc) metal or aluminum-scandium (Al-Sc) alloy by the calciothermic reduction of scandium oxide (Sc2O3). In this study, aluminum (Al) and calcium chloride (CaCl2) were used as the collector metal and flux for the reduction, respectively. A mixture of Sc2O3, Al, and CaCl2 in a tantalum crucible was placed inside a stainless steel reaction container, and the feed mixture was reacted with calcium (Ca) vapor at 1273 K for 6 h. After the reduction experiment, the reaction product (CaO), CaCl2 flux, and excess Ca reductant were removed from the obtained alloy sample by leaching with an aqueous solution. The formation of Al3Sc in the Al matrix phase of the alloy was confirmed by X-ray diffraction (XRD) and electron microprobe analysis (EPMA). This result indicates that Sc2O3 was successfully reduced to metallic Sc and alloyed in situ to form liquid Al-Sc alloy during the reduction. When Al was not used in the reduction experiment, a complex oxide (CaSc2O4) was formed, and the reduction was incomplete. This study demonstrates that the Al-Sc alloy can be directly produced by calciothermic reduction using CaCl2 flux and Al collector metal.

Jan 1, 2006

By N. Choi

The distribution behavior of selenium and tellurium in nickel sulfide smelting was investigated in the temperature range of 1250-1300 °C under an inert gas atmosphere and various oxygen partial pressures. The distribution coefficients of selenium and tellurium between nickel-copper-iron matte and silica-saturated iron silicate slag were detennined in terms of matte and slag compositions, temperature, and oxygen partial pressure. The effect of slag additives such as CaO, MgO, and Ah03 on the distribution coefficients of those elements was also investigated. It was observed that the distribution coefficients of selenium and tellurium increased with increasing matte grade and temperature. The solubility of selenium and tellurium in the slag decreased with increasing the partial pressure of oxygen within the range investigated in this study. The distribution coefficients of selenium and tellurium increased with the amount of CaO and MgO. Tellurium distribution coefficients also increased by the addition of Ah03. Meanwhile, the addition of Alz03 decreased the distribution coefficients of selenium at high matte grade.

Jan 1, 1996

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011