Search Documents

By Michael Amick

Due to the importance of maintaining open airways on a longwall panel, mine management decided to install cribs made of foamed cement. Foamed cement had been used at other company operations on several projects. A recent test at a sister operation had proven the crib installation technique and established that foamed cement cribs could provide better support than wooden cribs. The area to be supported was in a remote location; the limited material needs of foamed cement cribs offered a substantial advantage. In mid February 1993, 75 foamed cement cribs were installed on the tailgate of the active longwall panel. The 75 cribs resisted both horizontal and vertical stresses while successfully supporting the entry.

Jan 1, 1993

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By M. Craig Miller

As the trend continues in the U. S. toward inceased capital investment in longwall mining equipment and wider panels. the risk also increases for gotential financial and production loses due to undetected geologic anomalies. This paper describes how RIM Sm (Radio Imaging Method) is utilized in conjunction with more traditional exploration and interpretive methods to delineate fluvial channels. displacement faults and poor roof conditions in a Southeastern Ohio coal mine

Jan 1, 1990

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Peter Hatherly

As a discipline, geophysics covers an enormous range of scales and applications - from planetary geophysics through to the monitoring of acoustic emissions of rock samples. Although it is not a core discipline within the mining industry, geophysics has a useful role in providing information on the nature of the rock mass and the way it is responding to the mining process. For coal mining purposes, geophysical studies mainly seek to - delineate boundaries between the coal and the various layers within the surrounding strata - determine the physical properties of the rocks in-si tu, and - monitor the response of the rocks to the mining process Some of these applications may be associated primarily with mine planning, but once a mine is underway, most geophysical results can be used for the purposes of ground control. For example, insights into the nature of a geological fault mapped by a 3D seismic reflection survey will be relevant to determining support requirements while mining through it. In some instances there are parallels in the use of geophysics by the petroleum industry. Seismic reflection and wireline logging techniques have mainly been developed for petroleum exploration where their on-going development continues to provide spin-offs for the coal industry. The 3D seismic survey techniques that we now routinely employ were in their infancy 25 years ago and, almost certainly, the high quality borehole scanning tools that are now available would not have been developed without the need for petroleum well evaluation. Mining has also led to the development of specific techniques. An example is microseismic monitoring for the management of roof conditions during longwalling, and also the prediction of rock and coal bursts. The use and success of this technique have grown greatly over recent years. Another example lies with the use of geophysical wireline logs to predict rock strength and in rock mass classification. Coal seams also provide an unusual geophysical situation in that they form seismic and electromagnetic waveguides. The in-seam seismic and radio imaging methods have been developed to exploit these geological properties. In this paper I address the development and application of geophysical methods such as these with a particular emphasis on their role in ground control. We will see that there have been many developments over the past 25 years but we should also think about the future and how geophysics needs to be developed. From a miner?s perspective, one obvious area of need is in the detection of voids in the vicinity of current mine workings, be they old workings or karsts within nearby carbonate beds.

Jan 1, 2006

By D. A. Donato

It is often necessary for a mining company to extract coal from a seam underlying a previously mined coal seam. The impact of the overlying mine workings on the stress distribution within the underlying mine workings is very difficult to assess without the use of numerical modeling techniques. This paper demonstrates the usefulness of applying numerical modeling to evaluate alternate startup-room locations for a longwall panel considering the effects of multiple seam interaction. MULSIMIPC, a code adapted by the former U. S. Bureau of Mines, was used to compare stress patterns in two proposed startup-room locations. These model results were not only compared to each other, but also to results from a model with no overlying mine workings to provide baseline criteria for evaluation of the two proposed startup-room locations. The numerical modeling study was successful in providing useful information to the coal company and the regulatory agency (MSHA), resulting in a mine design that was both safe and efficient, and prevented the sterilization of a large volume of coal reserves.

Jan 1, 1996

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By Bill Stormes

This paper will discuss implementation of the Hilti OneStep rock anchor technology to improve face bolting operations during the May 2008 longwall move; increase rock anchor installation capacity; and improve safety by reducing employee exposure periods by utilizing the Hilti OneStep rock anchors.

Jan 1, 2008

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By Kot F. Unrug

In the premining stage of engineering design, the only available data are obtained from core drilling. It is often not sufficient for a realistic design of strata control. During the development, an access to the geological formation is created, enabling in situ testing. Obtained data can be utilized accordingly to improve preliminary design. The available methods for testing are described with emphasis on their application for a longwall system. The optimum design ensuring continuous operation of the high output longwalls is critical because their downtime is very expensive. Optimization of ground control measures also has the potential for substantial savings by elimination of unnecessary support.

Jan 1, 1994

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996