Search Documents

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By J. Kretschmann, R. Amiri

"The Sangan iron ore mines (SIOM) in Iran are located in a remote area near the Afghanistan border. The SIOM deposit contains a geological resource of 1.1 Gt (1.2 billion st) of mostly magnetite with an iron (Fe) grade ranging from 27 to 61 percent. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development is an influential ethical concept in mining all around the world. However, a successful realization of a sustainable development plan is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes sustainable development activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators were filtered to the ones with the highest priority for the stakeholders. Moreover, Islamic values and Iranian regulations and their influences on SIOM were analyzed.Mining industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron, etc., with 33.5 Gt (37 billion st) of proven reserves and more than 51.7 Gt (57 billion st) of potential resources. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5,316 active mines and 84,922 employees in the whole country in 2012-2013 (2) and, according to the statistics published by Central Bank of Iran (CBI) in 2011, the share of this sector in the gross domestic product (GDP) of the country was 1.2 percent (3)."

Jun 1, 2016

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By MATT RENAUD, Mustafa Kumral

As high-quality mineral deposits are thoroughly exploited, mines of the future will have to move towards more remote and lower quality projects. With these projects comes an increased business risk to the operator. Even now, mining companies often turn to foreign countries for new deposits to produce, introducing the concept of country risk into their portfolio. Furthermore, feasibility studies often fail to accurately quantify the risks associated with various projects, and as such, this study proposes a technique of risk quantification which can both aid mining companies to evaluate the viability of investment and assist in risk disclosure to public investors for the mining industry of the future. This paper aims to quantify the effects of country risk on the valuation of potential mining projects, using a combination of modular and risk-weighting techniques to evaluate the country risk premium (CRP) required to obtain capital for operation of risky foreign mining projects. The techniques proposed in this paper are demonstrated using fictional examples and then evaluated for accuracy against a recently developed debt-funded precious metal project in a country in the Americas.

Sep 30, 2021

By O. V. Bush

Most governments recognize that energy efficiency represents a partial solution to reducing global capital shortages and environmental crises that threaten to seriously impede economic growth. Much of the United States and many foreign countries are embracing the concept of Integrated Resource Planning (IRP) which incorporates Supply Side Management (SSM) and Demand Side Management (DSM). Since SSM comes at twice to three times the cost of DSM, it makes economic sense to employ the energy conservation techniques of DSM. This paper will explain these concepts and some of the incentives being put forward by governments and utilities to promote DSM.

Jan 1, 1995

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

By G. W. Douglas

The need for dimensionally stable filled polymer composites has spurred the quest for materials that possess a negative coefficient of thermal expansion (CTE). Finding minerals and materials with a negative CTE large enough to counteract the substantial CTE found in polymers proves challenging. Much research has been per-formed over the last decade to uncover various materials that possess this unusual behavior. A list of materials that have demonstrated negative properties are discussed, as well as the experimental use of one such material (ZrW2O8), in a polymer matrix composite. Other negative properties, such as negative Poisson?s ratio and negative stiffness, are also examined. Key words: Negative properties, Coefficient of thermal expansion, Zirconium tungstate

Jan 1, 2010

By J. D. Miller, C. L. Lin

Filtration of fine particles involves filter cake formation and removal of surface moisture by drawing air through the porous structure. Accurate assessment of the transport properties of porous media (in this case, filter cake) is of major importance in the development of improved filtration processes. Implications from these studies are important in the design and operation of filtration equipment in order to enhance the efficiency of this important solid-liquid separation process. The microstructure and connectivity of pore space are important features necessary to describe detailed fluid flow phenomena in filter cake during fine particle filtration. In this regard, 3D characterization of pore structure is essential. The pore structure has to be described by parameters which are of special relevance to the interpretation of fluid transport phenomena. These parameters should be based on directly measured variables of the pore system and not inferred from indirect variables (such as those determined empirically from transport processes) valid only for a particular pore structure. In this way fundamental relationships between pore structure and fluid transport at the microstructure level can be described. In order to achieve this level of sophistication the three-dimensional interconnected pore structure of filter cake must be determined. Study of fluid transport phenomena in filter cake using x-ray microtomography to characterize the complex three-dimensional pore geometry is discussed. On this basis the Lattice-Boltzmann (LB) method is used to simulate and to establish a fundamental relationship between pore microstructure and effective transport coefficients.

Jan 1, 2002

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993