Search Documents

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By P. R. Segopolo

"The purpose of the project is to convert current shuttle car utilization on an underground coal mine to best practice by focusing on change-out points and tramming routes, which have a major influence on shuttle car away times. Time studies were an integral part of the project as these enabled the determination of shuttle car away times. An indirect proportional relationship between shuttle car away times and productivity is established. Through the time studies, it is deduced that a third shuttle car will make an insignificant contribution to production when there is only one split open. During this time, maintenance on the third car can be optimized. In order to satisfy the mine’s key performance indicator of keeping shuttle car away times less than 75 seconds, a belt extension must be scheduled after the third split is open. It is established that at any given time, a minimum of two shuttle cars should be used. When cutting on the left-hand-side of the belt road with only two shuttle cars available, the centre and left (left of the feeder breaker) shuttle cars should be used for coal hauling. When cutting on the right-hand-side, the centre and the right-hand-side cars should be used. If only one shuttle car is available, the centre car is the most efficient to use. Alternative anchoring configurations can be employed so as to enable cars (left or right, especially) to reach the opposite extremities of the panel and hence minimize cable length restrictions. Paper written on project work carried out in partial fulfilment of BSc. Eng. (MiningEngineering)"

Jan 1, 2015

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

By M. W. Hildyard, M. O. Kataka

Seismic integration schemes aim to incorporate the rock mass response provided by the historical seismic activity to improve the ability of numerical models to reproduce future response to mining. Up to now, integration schemes considered the events using quasi-static models. This paper presents case studies that consider some of the seismic and modelling issues needed to extend these schemes to include the dynamic characteristics of seismic events. The ultimate aim of an automated integration scheme seems impractical for dynamic modelling. The predictions of the WAVE elastodynamic finite difference program are, however, suitable for modelling limited numbers of events to determine either the near-field velocities and damage or the effect of fractures and excavations on the far-field low frequency response. Les projets d’intégration sismique ont le but d’incorporer la réponse de la masse rocheuse à l’activité sismique historique pour améliorer la capacité des modèles numériques à reproduire la réponse future à l’exploitation minière. Jusqu’à présent, les projets d’intégration étudiaient les évènements avec des modèles quasi-statiques. L’étude présente révèle des études de cas qui considèrent certaines des questions concernant modelage et séismes qui sont nécessaires pour porter plus loin ces projets en incluant les caractéristiques dynamiques des évènements sismiques. Le but final d’un projet d’intégration automatisé semble impraticable pour la modélisation dynamique. En revanche, les prédictions du programme élastodynamique par la méthode des différences finies WAVE sont appropriées à la modélisation d’un nombre limité d’évènements de façon à déterminer soit les vitesses à petite échelle et les dommages, soit les effets des fractures et excavations sur la réponse de basse fréquence à grande échelle. Seismische Integrationsschemata zielen darauf ab, Reaktionen der Gesteinsmasse, die von den Berichten seismischer Aktivitäten stammt, zu inkorporieren um numerische Modelle in die Lage zu versetzen, künftige Antwort zum Bergbau zu reproduzieren. Bis dato betrachteten Integrationsschemata die Fälle mit quasi-statischen Modellen. Diese Arbeit stellt Fallstudien dar, die einige der seismischen und modellierenden Fragen betrachten, die benötigt werden, um diese Schemata auszuweiten, um die dynamischen Charakeristika seismischer Fälle einzuschließen. Das Endziel eines automatisierten Integrationschemas erscheint für das dynamisches Berechnen undurchführbar. Die Vorhersagen des WAVE elastodynamisch begrenzten Unterschiedprogramms sind jedoch verwendbar für das Berechnen von begrenzten Anzahlen von Fällen, um entweder die Nahfeldgeschwindigkeiten und Schaden oder den Effekt von Brüchen und Extraktionen auf der Fernfeld Niederfrequenzantwort festzustellen.

Jan 1, 2003

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004