Search Documents

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By B. Dimitriades

Data on smog-forming reactivities of exhaust aldehydes are scarce. Such data were obtained by irradiating in a smog chamber typical exhaust aldehydes, individually and in exhaustlike mixtures. Observed reactivity manifestations were rate of nitrogen dioxide formation (RNO2) and yields of oxidant, peroxyacetyl nitrate, and formaldehyde. Results showed that exhaust aldehydes vary widely in reactivity. Formaldehyde showed high RNO2 reactivity but low oxidant yield; benzaldehyde, [m]-, and [p]-tolualdehyde were totally unreactive when irradiated individually; [o]-tolualdehyde was reactive. In mixtures, benzaldehyde manifested reactivity in terms of peroxybenzoyl nitrate yield. Exhaust aldehydes as a group are judged to be as reactive as the exhaust olefin group. The importance of the aldehyde contribution to exhaust reactivity and methods for assessing such contribution are discussed.

Jan 1, 1971

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By Kung-Lee Wang

The 1963 performance of the United States economy was impressive. The year was one of continued growth unmarred by a recession. By the end of 1963 the economy's expansion had already lasted almost as long as the 1954-57 upswing, and the net gain in output since the trough in activity in early 1961 compared favorably with most earlier postwar cyclical advances. There was no indication of any slow- down at yearend. Both gross national product (GNP) and national income in 1963 were 5 percent higher than in the previous year. GNP totaled $584 billion, a gain of $28 billion over 1962. Real output of goods and services rose 3.4 percent over the year. Price increases continued to be moderate. Production, employment, personal income, and corporate profits all registered new but unemployment continued high at 5.5 percent and the prospects for improvement remained poor. The economy again failed to use its full potential. Current value of mineral production kept pace with the economy. The constant dollar value of mineral production gained more than real GNP because of the relatively stable price of minerals. Mining production achieved a new high in 1963. Steel production totaled 110 million tons, 12 million tons above 1962, making 1963 the first 100- million-ton year since 1957 and lifting the steel-associated minerals group upward. The gain in ferrous metals mining was insufficient to compensate for the decline of nonferrous metals mining resulting in an insignificant decline in the metal mining total as a whole. The upsurge of construction material minerals output, with an assist from chemical and fertilizer minerals, accounted for peak production of

Jan 1, 1964

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By S. J. Page, J. A. Organiscak

Dust surveys were conducted around small truck-mounted rock drills operating at surface coal mines to assess their airborne respirable dust generation and in-service dust control methods. Of four out of seven drills sampled, respirable dust concentrations measured around the drill deck ranged from 8.68 to 95.15 mg/m with3concentrations ranging from 1.37 to 2.69 mg/m at distances 12.2 to 30.5 m downwind of these drills. The other3drills had noticeably lower respirable dust concentrations measured around the drill deck at or below 1.30 mg/m.3Rotoclone-type dry dust collectors were commonly used with dust being emitted from around the drill deck shroud, collector exhaust, and collector fines dumping. Wind speed and direction was also a factor in the dust concentrations measured on the bench. Dust control modifications were made to three rock drills to reduce their airborne dust emissions. Dust controls tested included water injection into the Rotoclone exhaust, Rotoclone exhaust extension, improved sealing of drilling deck shroud, shrouding the Rotoclone hopper dump process, and wet drilling. These control techniques showed noticeable improvement in dust concentrations measured around the drills. Finally, repositioning the drill operator showed that operator dust exposure can be improved by avoiding the dust cloud around the drill.

Jan 1, 1995

Reduce longwall shearer operator's dust exposure by selecting the best drum water spray sys-tem for minimizing dust generated durinq cutting. Approach Three of the most commonly-used drum water spray systems were installed on the same set of shearer drums and compared to determine which system best suppresses dust. The spray systems studied were: ? pick-point flushing ? cavity filling ? water-through-the-it Instantaneous and gravimetric sampling instruments were used to measure the respirable dust exposures of the shearer operators and dust concentrations downwind of the shearer. The Three Systems: Longwall shearer drums are routinely equipped with internal drum spray systems since these systems have been shown to be more efficient than external systems in terms of dust suppression per gallon of water applied. All U.S. longwall shearer faces utilize some type of internal water delivery spray system. The two most common systems are bit-or pick-point flushing and cavity filling. Pick-point flushing uses nozzles mounted in the bit blocks or in special blocks immediately in front of the bits. Cavity filling utilizes spray nozzles installed in a pipe manifold mounted on the drum hub between the scrolls or along the edge of the vane scrolls; water is sprayed radially from the manifold towards the adjacent vane scroll.

Jan 1, 1986

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

Provide the National Park Service (NPS) with guidelines for closing abandoned mine openings such as shafts and adits. Approach The NPS needed alternative methods of closing a variety of abandoned mine openings on National Park lands. Because the U.S. Bureau of Mines (USBM) has a long history of mining-related experience, the NPS requested that the Bureau provide them with technical mine closure information. USBM engineers compiled information on various types of mine closures and prepared technical illustrations of those closure techniques. Multiple closure options, by type of opening, were prepared as one-page field guides to assist NPS field personnel in determining the most appropriate closure method for a given situation and detailing the construction of the closure method. Results Guidelines provided to the NPS included a description of the method, use applications, construction techniques, technical illustrations, and technical support information. The following provides a brief description of 11 mine closure techniques identified for use by NPS personnel. Most of the closure methods, except the backfill methods, allow for construction that can provide access to the mine. However, providing access makes the closure susceptible to vandalism. Most closure methods require periodic monitoring for subsidence and corrosion or deterioration of construction materials.

Jan 1, 1994

By Jeran Paul W., Michael A. Trevits

Subsidence data gathered by the U.S. Bureau of Mines over a series of longwall panels in the Pittsburgh Coalbed were studied to obtain insight as to the role of time in the subsidence process. It was found that subsidence began essentially with undermining and was completed within 1 year. The progress of the subsidence was dependent upon location above the panel. Subsidence in the central area of the subsidence trough, where subsidence is the greatest, was about 90 pct complete by the time the face had progressed a distance equal to one overburden thickness beyond a particular surface point. For a point over the rib of the longwall panel, the subsidence was only about 60 pct complete at this time. Data from three other sites in the northern Appalachian Coal Basin were analyzed to determine if an anomaly or the true characteristics of the subsidence process had been observed. All sites behaved similarly in the central portion of the subsidence trough. However, the subsidence of points over and adjacent to the ribs of the longwall panels was site specific. The fact that movement across the width of the panel was not uniform should be taken into account in assessing damages or the potential for damages resulting from mining-induced subsidence.

Jan 1, 1995

By William A. Hoffman

In This Chapter [MSHA regulations for coal mines MSHA regulations for metal/nonmetal mines OSHA regulations for tunnel construction Types of respirators used in mines and tunnels Filter materials and filter efficiencies Donning, seal checking, and maintenance Filter service life and Respirator information resources] In many cases, engineering controls are not adequate to achieve satisfactory dust levels, so respirators must be used. This chapter explains the Federal regulations governing the use of dust respirators in mines and tunnels and describes the most common dust respirators used. Filter materials and filter efficiencies for respirators are discussed. This chapter also gives some guide-lines for respirator use and recommends sources for more dust respirator information. Respirator effectiveness in reducing dust exposure usually exceeds the effectiveness of most engineering control methods. RESPIRATOR REGULATIONS [Different regulations govern respirator use in coal mines, metal/nonmetal mines, and tunnels under construction.] Coal mines under Mine Safety and Health Administration (MSHA) jurisdiction. Coal mine operators are required to meet dust standards using only engineering control methods. Typical engineering control methods include ventilation and water sprays. Respirators are not regarded as an engineering control method, so respirators cannot be used in lieu of engineering controls.

Jan 6, 2003

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By J. M. Gomes

The Bureau of Mines investigated electrolytic techniques for preparing diborides of the group IV B metals. TiB2, ZrB2, and HfB2 were electro-deposited from their respective oxides dissolved in borate-chloride-cryolite electrolytes. Titanium diboride was also electrodeposited from rutile (Ti02) dissolved in a Na2,B4O7-Na2C03-Na3A1F6-NaC1 electrolyte at 1,050° C; 14 kW-hr were required to produce 1 pound of TiB2. Major impurities in the TiB2 produced in a 10-deposition cycle experiment, in weight-percent, were Al, 0.2; Cr, 0.3; Fe, 0.1; V, 0.3; C, 1.4; and 0, 1.0. Zirconium diboride was electro-deposited from zircon (ZrSiO4) dissolved in a Na2B407-NaOH-Na3A1F6-NaCl-NaF electrolyte at 1,050° C. The ZrB2 produced in a 10-deposition cycle experiment contained the following impurities in weight-percent; Fe, 0.1; Si, 0.5; C, 0.3; and 0, 0.6. Energy required to produce 1 pound of ZrB2 was 9.3 kW-hr.

Jan 1, 1975

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

Reduce spillage hazards and contamination when adding hydraulic nil to mining machine reservoirs. Approach An easily transported module, that delivers hydraulic oil directly into mining machines, was built and tested. How It Works The Hydraulic Oil Delivery Module is carried, from the oil storage area to the equipment needing oil, in the bucket of a scoop or other utility vehicle. Oil is pumped into the module reservoir from storage, or out of the module reservoir into the machine being serviced, through a long hydraulic hose. During long-term testing, the 115 foot long delivery hose made it possible to replenish the hydraulic oil in mining machines at the face with only limited interruption to the mining operation. (Figure 1 shows one! version of the module.) The compact Hydraulic, Oil Delivery Module consists of: an oil reservoir: a pump driven by a hydraulic motor; two high pressure, low volume oil lines, filters; and a low pressure, larger capacity delivery hose equipped with quick-connect-couplers. The high pressure oil lines are connected to the scoop's hydraulic power takeoff, which supplies the power to pump oil in or out of the module reservoir.

Jan 1, 1977

By J. M. Kuchta

The chemical and thermal criteria used for predicting the spontaneous combustion hazard are briefly reviewed and data are presented to characterize the gas desorptions and self-heating tendencies of 29 U.S. coals. Closed vessel desorption experiments showed that CO, CO2, and CH4 are the main gases evolved and that the CO, CO/?O2 index, and 02 absorption rate increase with decreasing rank and increasing oxygen content of the coal. In this Bureau of Mines report, the effects of temperature, moisture, and other variables are discussed together with the application of the data to the complex conditions encountered in a mining environment. An important finding is that the presence of CO alone in a mine is not necessarily an indication of a self-heating reaction of the coal. Based upon experiments conducted in an adiabatic-type calorimeter, the self-heating temperatures of lignite and subbituminous coals can be as low as 30° C, whereas the bituminous coals require a temperature of about 60° C or more. The self-heating hazard is greatest when the coals are dried and exposed to a high humidity condition, apparently as a result of the "heat-of-wetting." Generally, the hazard is greatest with the western coals of the United States.

Jan 1, 1980

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974