Search Documents

By Jack C. White

This U.S. Bureau of Mines report assesses the resource potential of trace metals present in commercial Ti mineral concentrates. Metals of greatest interest: are those defined as "strategic and critical" by the U.S. Congress in 1981. Metals of interest in Ti mineral concentrates are Cb, Cr, Ta, Th, U, V, and Zr. Commercially available Ti mineral concentrates were studied. Characterization and analysis of major and minor constituents were performed by X-ray diffraction, neutron activation, inductively coupled plasma emission, atomic absorption, and classical wet chemical techniques. Of the metals investigated, the Cb, Ta, and V content of some concentrates may be a significant potential resource, depending on their amenability to recovery.

Jan 1, 2010

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Arkansas has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251 of which this is the tenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of which deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated. and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By A. L. Johns, M. V. Healey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of tie laws of Ecuador has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State..

May 1, 1930

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By D. Harrington

Correct ventilation of underground workings whether in coal or in metal mines consists in establishing such control of air currents that the miners may work in safety, with maximum comfort and efficiency, and without impairment of health; also in controlling the air flow so that the mine workings may at ordinary times be kept reasonably free of harmful gases or dusts, and so that in time of emergency, as when a fire or an explosion occurs, there may with minimum delay be maintained as much or as little air flow as is desired throughout the mine in its entirety or in certain parts of the mine. Control of air flow is the essential point of any mine ventilating system, and is obtained only by the installation of mechanically operated fans, and other ventilating devices such as doors; overcasts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. Much has been written about natural ventilation, and many claims have been made that in specific mines or parts of mines there is sufficient natural air flow. As a matter of fact, there are actually very few if any mines, coal or metal, where natural ventilation creates atmospheres anything like adequately safe or healthful for underground workers even at ordinary times or under ordinary. conditions; and at the time of a fire or an explosion mines depending upon natural ventilation are practically helpless, and are decidedly dangerous for the unfortunates forced to be in them either at the time of the disaster or afterwards when trying to handle conditions arising from the emergency.

Jan 1, 1929

By Jack E. Fraley

In this Bureau of Mines study, sealants containing mineral wool, cement, etc, were sprayed through dry-process equipment that propels dry material pneumatically to the water-adding nozzle. Advantages over slurry applications include no mixing, no extensive cleanup, and freedom from hardened cement in equipment should power be lost. Sealants with large mineral wool nodules (>l-inch) were sprayable at rates to 900 square feet per hour for 1/2-inch thickness with little dust and smooth material flow through equipment, but they were weak for mine use, Materials containing small wool nodules (1/4-inch) were stronger but tended to plug lines because the nodules were inadequately separated in the shredder. Increasing the dedusting oil also increased line plugging by holding the nodules together in larger lumps. Best results were obtained using a 3/4-inch-nodule wool with cement binder, which provided both smooth flow through the machine and adequate strength.

Jan 1, 1977

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage arc also described. IntroductionThe association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate ·formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation.In its most general form, the process of agglomeration involves taking discrete, independent particles, bringing them into contact with one another, promoting (or allowing) interparticle adhesion to occur and then causing structure rearrangement, usually under the action of external forces. The relative importance of these steps varies with the nature of the particulate system being agglomerated and with the kinds of agglomerates being produced. Coagulation or flocculation of particles dispersed in fluids is generally dominated by the contact and adhesion steps. In the granulation of powders, on the other hand, particles are already in contact so that structure rearrangement is the principal step."

Mar 1, 1992

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957