Search Documents

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By John B. Gayle

The suitability of fluid petroleum coke as a blending agent for producing metallurgical coke has been investigated using the Tuscaloosa and sole-heated experimental ovens. From the results of tests with three representative blends, it has been fond that additions of fluid petroleum coke effect the following changes: (1) Increase in size, resistance to shatter, and apparent specific gravity of cokes produced; (2) little or no change in coke hardness and stability or in the amount of breeze formed; (3) increased charge density; (4) modification of expansion characteristics of blends charged; and (5) decreased ash and increased sulfur contents of blends charged and cokes produced. Substitution of a calcined sample of fluid coke of greatly reduced sulfur content resulted in a coke of inferior physical properties. This effect indicates that additions of the calcined product should probably be limited and that other methods for producing a low sulfur fluid coke should be considered.

Jan 1, 1956

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By K. K. Kelley, W. W. Weller

The heat capacities of four crystalline silicates of barium ( BaSiO3 , BaSiO4 , Ba Si¸0 , and BaSi₂0 ) and two crystalline silicates of strontium (SrSio and Sr₂Sio ) were measured over the temperature range from 51 ° to 298° K. The results were used to evaluate the entropies at 298.15 ° K. The entropy values were joined with known heats of formation to obtain the free energies of formation of the silicates with respect to their constituent oxides at 298.15 ° K.

Jan 1, 1964

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954

[In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or a blasting device enumerated in the permissible lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.]

Jan 1, 1941

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or y blasting device enumerated in the permissible Lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1941

By L. Nahai

COAL, salt, lapis lazuli, and construction materials such as lime, gypsum, slate and stone were the only mineral commodities produced in Afghanistan during 1963. Beryl has been produced sporadically. Small deposits of chromite and lead-zinc are known but remained unexploited because there were no domestic markets for the two commodities and transportation costs from Afghanistan to world markets were too high. Oil fields of sufficient magnitude to justify exploitation have not been discovered, but known natural gas reserves are substantial and have potential significance. There is evidence of large high-grade iron ore resources, but these are in an unfavorable location. The contribution of the mineral industry to the economy was small, although precise figures are not available. The reported value of mineral production in 1963 (excluding barite) was 181.6 million afghanis (about US$4 million). Employment in the industry, including cement plants and quarries, was estimated to be no more than about 2,000.

Jan 1, 1964

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By F. F. Aplan

"The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.INTRODUCTIONCoal is a black or brownish-black combustible solid, derived from a heterogeneous mixture of plant remains and associated mineral matter that have undergone chemical and physical metamorphic changes by biological and geological processes without free access to air. It is composed principally of carbon, hydrogen and oxygen with lesser amounts of nitrogen and sulfur. 'Its exact chemical and physical nature has remained poorly defined, because the term 'coal' refers to a broad range of coalified solids ranging in rank from anthracite to a variety of bituminous coals of differing volatile matter content, sub-bituminous coals, and ending with lignite and brown coals. The variation in chemical and physical properties through these ranks is massive. In summary, Luckie's (1988) assertion is apropos: ""There is no such thing as coal; there are coals"". The coal preparation engineer, and, most especially, those scientists and engineers from other disciplines wishing to work with coal, must constantly keep this admonition in mind because what is true for one coal seam is often not directly applicable to another."

Jan 1, 1989

By Robert M. Doerr

The oxidation kinetics of Ni-Y alloys in the range 0.04 to 8 weight-percent Y, and of high-purity Ni, were compared by the use of a sensitive volumetric apparatus. The reactions followed approximately the parabolic rate law; for oxidations in 02 at 0.5 atm and 1,200° C, the parabolic rate constant was about 0.37 + (0.064) (Y-2.11) mg cm-2 min-1/2, where Y represents the weight-percent Y in the alloy. Internal oxidation of Y occurred in the alloy specimens and the resultant Y203 particles, which were in patterns related to the eutectic structure of the alloys, served as markers showing that the subsequent oxidation of the surrounding Ni was by inward diffusion of O. The scale consisted in each case of NiO, but the inner parts of the scale on the alloy specimens included the patterned Y203 particles. The thicknesses of the inner parts of the scale depended directly on the Y concentration, and the thicknesses of the Y2O3-free outer parts of the scale were inversely related to the Y content of the alloys. There is thus a relationship between the thickness of the outer part of the scale and the protectivity of the scale. Outward diffusion of Ni and inward movement of 0, from the inner boundary of the Y2O3-free part of the scale, is proposed as a mechanism for these results.

Jan 1, 1966

By R. Hogg, J. M. Mutmansky, E. Kaya

"Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research.The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, nonrespirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.INTRODUCTIONRecently, a considerable amount of research effort has been directed toward better understanding of the characteristics of the coal dust generated during the mining process. It is generally believed that dust characteristics play a significant role in the development of Coal Workers' Pneumoconiosis (CWP). In order to effectively protect coal workers from coal dust, it is important to understand the properties of dust, the mechanisms of generation and dust-lung reaction. Conducting research on dust characterization, dust control and the biomedical aspects of dust toxicology generally requires a large sample of airborne coal dust. Unfortunately, current dust sampling instruments are not able to meet this demand because only a few milligrams of dust are collected."

Nov 1, 1995

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994