Search Documents

By Joseph J. Wallace

1. The Investigation shows that there are six coal beds of major importance in McDowell County from the standpoint of present production - Pocahontas No. 3, Pocahontas No. 4, Pocahontas No. 5, Sewall, Beckley, and Pochontas No. 6 - and five beds of minor importance - Iaeger, Douglas, Welch, Pocahontas, No. 9, and Eagle. The Pocahontas No. 3 bed contains the largest remaining, known reserves. 2. Known measured, and indicated reserves in all beds, based on a minimum thickness of 174 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,217 Trillion short tons as of January 1, 1951. Of this total, 1,731 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these area, such reserves should be added to he total estimated reserves.

Jan 1, 1952

By O. W. Terry

The Skene mine, in the Elizabeth District, Illinois, produced lead are from 1901 to 1907. Three exploratory holes drilled just north of the mine were said to have penetrated 40 feet of good zinc are. During the summer of 1944, the Bureau of Mines drilled check holes close to what appeared to be two of the three old holes. They also drilled two holes to the south of the mine and one into the core of the deposit. Results of the investigation are given in this report.

Jan 1, 1948

By F. E. Griffith

[Unquestionably mine fires new constitute one of the chief causes of sabotaging the effort to produce maximum quantities of mineral products essential to the prosecution of the war. This applies more particularly to coal than to noncoal mines, and presumably the main reason for this is the fact that coal production in maximum quantity is still very much a "must", while the demand for much of the product of noncoal mines has eased materially in recent months.]

Jan 1, 1944

By J. Feldman

This report contains a description of the distillation laboratory at Bruceton, Pa., which was established to aid in the separation and identification of the products produced in the synthetic liquid fuel processes under study there. Compounds present in synthetic liquid fuels may include aliphatic from C1 to C60 or greater. Alcohols, ketones, esters, aliphatic carboxylic acids, saturated hydrocarbons, olefins, and diolefins are all found in Fischer-Tropsch products. Coal-hydrogenation products contain, in addition to aliphatic compounds, a large proportion of naphthenic material and aromatic compounds ranging from benzene to coronene; in addition, appreciable quantities of tar bases and tar acids are present. In designing the laboratory, therefore, provision had to be wade for the greatest amount of flexibility and versatility. A great deal of standardization of basic equipment had also to be designed to permit interchange of parts and services.

Jan 1, 1951

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By Oliver W. Keener

This paper describing the methods and costs of mining at the Hartley-Grantham mine of the Century Zinc Co. in the Tri-State Lead and Zinc district is one of a series being prepared by the United States Bureau of Mines can mining practices, methods, and costs in the various mining districts of the United States. LOCATION, HISTORY, AND GEOLOGY The Hartley-Grantham Mine is located just outside the city limits of Baxter Springs, Kans., as shown in Figure 1. A plan of the mine is given in Figure 2, and Figure is a cross section through A - A of Figure 2.

Jan 1, 1930

By C. P. Mishra

The Bureau of Mines performed a study of the availability of cobalt from market economy countries. The study entailed the detailed analysis of 97 deposits which contain 3.9 billion lb of cobalt at the demonstrated level; in 94 of the deposits cobalt is recovered as a byproduct, and in 3 it is considered the primary product. Since 97 pet of all recoverable cobalt is derived as a byproduct from copper and nickel deposits, the report focused on these two sources. At an assumed market price of $0.89flb for copper, $3.45/lb for nickel, $475/tr 021 for platinum, and $7/lb for cobalt, 1,330 million lb of cobalt at the demonstrated level are potentially available. This total includes 1,105 million lb of cobalt from copper properties, 190 million lb from nickel, 29 million lb from platinum, and 6 million lb from primary cobalt. This analysis indicates that the production cost for 589 million lb of cobalt can be totally covered by the revenues obtained from the other metals produced. The impacts of increases in capital investment and energy costs are also discussed.

Jan 1, 1985

By Dean H. Ambrose

The U.S. Bureau of Mines recently developed computer graphics simulations to characterize mining scenarios, specifically for room-and-pillar mining operations in a three-entry longwall development section. These simulations compare productivity between shuttle car and continuous haulage systems concepts. One of the continuous haulage systems concepts has bolting capabilities that supplement haulage function. Simulations showed the continuous haulage system to be more time efficient than the shuttle car system. Researchers can reuse the simulation code (e.g., mining rates and equipment capacities can be changed) should investigators care to compare production of other mining scenarios. computer simulation, found computer model modification flaws and mining scenario conceptual errors. The fundamental rationale for three-dimensional computer is to cheaply, easily, and quickly obtain information about operation and of a current or proposed mechanical coal or metal/nonmetal mining system. This report documents the computer graphics model and simulation developments and discusses some of the results and observations from the simulations.

Jan 1, 1994

By G. W. Jones

In a previous report results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman, to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the rally exceptions which have been found, reference should be made to a report by Coward and Jones. Before this method can be used the inflammable limits of the individual constituents must be known. Also, the composition of the complex combustible mixture, and representative mixtures besides, must be tested both experimentally and by calculation to prove whether Le Chatelier's law may be applied.

Jan 1, 1933

By L. C. IlsLey

[The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Wheatstone-bridge axed catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detectors of the latter type have been approved since 1933. A brief description of each follows: U. C. C. Detector Approved No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was entered January 27, 1330, to cover important chances in design that permit checking; the calibration of the detector at any time, whether in gas or fresh air. Essential features of the detector are shown in figure 1.]

Jan 1, 1937

By Earl T. Hayes, W. M. Sternberg, F. P. Williams

"INTRODUCTION The limited domestic demands for lithium salts and metal before the war were met readily by the use of minerals particularly lepidolite (lithium mica) and amblygonite (a lithium phosphate), from which lithium can be recovered relatively easily. New wartime uses, however, created such a demand that it became necessary to turn to spodumene (a lithium feldspar) as the principal source of supply. Although very large deposits of spodumene occur in South Dakota and in North Carolina, it much more difficult to extract lithium from spodumene than from lepidolite or amblygonite.During the spring and summer of 1942 a study was made in Salt Lake City laboratory of the Bureau of Mines on the recovery of lithium from spodumede. Preliminary tests were made on two processes - roasting with potassium sulfate 4/ 5/ and roasting with calcium chloride and calcium carbonate 6/ -,which appeared to be the most promising of the various processes that had been proposed. By roasting spodumene with approximately its own weight of potassium sulfate at 1,050º C. and leaching the product with water, about 70 percent of the lithium could be extracted. Consumption of the relatively expensive potassium sulfate, however, was high; much of the potassium was found in the insoluble leach residue, end large amounts were lost by volatilization and dusting. By roasting the spodumene with calcium chloride and calcium carbonate, nearly 90 percent of the lithium was chloridized temperatures of 850° to 1,050° C. Much of the lithium could be extracted from the calcine by leaching with water after roasting at the lower temperatures, but volatilization of lithium chloride was appreciable, amounting to 20 to 25 percent in a direct gas-fired furnace at temperatures of 800° to 850° C. At 1,000° to 1,050° C., volatilization was far from complete. Thus, it would be necessary to use both fume collection and leaching of the calcine, unless the roasting temperatures were sufficiently high to volatilize all the lithium chloride. Because of the well-known difficulties of collecting chloride fumes, it was decided to search for a better process."

Mar 1, 1946

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By Sidney Katell

An economic analysis of underground gasification of coal, based on experimental results obtained by the Bureau of Mines, indicates that a gas suitable for use in a power plant might be produced for approximately $.62 to $.77 per million British thermal units. This estimate does not include cost of land purchase. The gasification experiments were conducted in a 3-ft. seam of high volatile A bituminous coal. The major factors which can influence a change in operating costs are height of overburden, power costs, thermal efficiency, and the gasification air inlet pressure. The following equations show the relationship of these factors to operating costs:

Jan 1, 1961

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By K. O. Bennington

Thermodynamic properties were determined by the Federal Bureau of Mines for lithium metasilicate (Li2Si03) and lithium disilicate (Li2Si205). Their enthalpies of formation were investigated by hydrofluoric acid solution calorimetry. The standard values are ?Hf°298 -393.8 ± 0.8 kcal/mole for Li2Si03, and ?Hf°298 -611.8 ± 1.0 kcal/mole for LiSi205. Enthalpy increments above 298 K were measured by copper-block drop calorimetry from 298 to 1,404 K for Li2Si03, and from 298 to 1,281 K for Li2Si205. Low-temperature heat capacities were determined adiabatically from 6 to 305 K for Li2Si205 only. The derived standard entropy is S°298 = 29.20 ± 0.10 cal/deg-mole. The various experimental data were combined with other data from the literature, and resulting properties of ?Hf°, ?Gf°, and log Kf were tabulated as a function of temperature.

Jan 1, 1976

By H. E. Harris

It has long been recognized that one of the principal ways of combating dust in coal mines is by means of water sprays. However, spray systems, currently in use, clog or plug frequently, thereby reducing the effectiveness of dust control aid, in turn, possibly increasing the health hazard to mining personnel. Moreover, the maintenance and replacement of spray system components, e.g., nozzles and filters, can be expensive in terms of direct costs of labor and material, and the consequent loss of production. Recognizing these problems, the Bureau of Mines sponsored a research project on the "Development of a Non-Clogging Water Spray System"; this project was carried out by Eastern Associated Coal Corp. The overall objective of this project was to develop a non-clogging water spray system suitable for use in underground coal mines. Since most of the dust formed is at or near the working coal face, emphasis was placed on face equipment such as a continuous mining machine. To accomplish this objective, a two-phase project was carried out. The first phase involved determining the causes of spray nozzle and spray system clogging, determining the availability of spray nozzles or systems that could be modified to be non-clogging, and developing a non-clogging water spray system. Phase two was concerned with the fabrication and the laboratory and field testing of a non-clogging system. In each phase, there were both laboratory and field investigations, and the results of these investigations are presented in this report.

Jan 1, 1975

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977

By A. J. Kraemer

This report on the physical and chemical properties of crude oils of California is one of a series on the producing districts of the United States. It includes a short discussion of results, tabulated data, and individual analyses of California crudes. Analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties have been published in Serials 25952 and 26083. The analyses reported in this paper corer samples that were obtained subsequent to the publication of Serials 2535 and 2608. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1927