Search Documents

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase

Jan 1, 1937

By Raymond W. Hiteshue, Sam Friedman, Robert Madden

Experiments were made in a semicontinuous unit to provide engineering data for designing experimental continuous systems . These systems would be used to study the hydrogasification of hvab coal and char (from lowtemperature carbonization ) to high - Btu gas . In experiments at 800 ° C and with a coal residence time of several seconds , yields of hydrocarbon gases increased from about 2,000 scf / ton of maf coal at 250 psig to 7,000 scf at 1,000 psig . With 15 minutes residence time , yields increased from 8,000 scf/ton of maf coal at 250 psig to 17,500 cubic feet at 1,000 psig . In all cases , small quantities of heavy oils were produced along with the gaseous hydrocarbons . Production of oils could be minimized with a corresponding increase in gaseous hydrocarbons by increasing the retention time of the volatiles within the hot zone . Yields of gaseous hydrocarbons from char were slightly greater than from coal under similar conditions . Although the hydrogasification reaction is very pressure dependent , substantial quantities of coal (40 to 60 percent ) could be reacted to gaseous hydrocarbons at pressures as low as 50 psig provided reaction temperatures were increased to 1,200 ° C. It was also demonstrated that a hvab coal could be hydrogasified continuously without incurring agglomeration . This was achieved by dispersing coal in a relatively large reactor with concurrent flow of hydrogen . At 1,000 psig and 800 ° C , it was possible to react about 35 percent of the coal and to produce a gas containing up to 52 percent methane .

Jan 1, 1964

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By Jr. Sillers

This is the third report of investigations dealing with the application of electrolytic manganese to steel-foundry practice and the seventh in a series of reports dealing with tests to establish the technological acceptability of electrolytic manganese in the iron and steel industries. The work was carried out by Metallurgical Division of the Bureau of Mines as part of an extensive program for the development and utilization of domestic ores. The electrolytic manganese used in the tests was produced by the Bureau at its Boulder, City, Nev., pilot plant by the process developed by the Bureau of Mines.

Jan 1, 1949

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase of the iron and steel industry. Thus, for the first time, producers, buyers, sellers, and consumers of iron and steel scrap have had an accurate statistical picture of this important raw material As originally contemplated, the study was to be continued on an annual basis, but, owing to budgetary limitations for the fiscal year 1937-38, the Bureau may be unable to conduct the canvass for 1937.

Jan 1, 1937

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

By P. H. Floyd

This report presents the results of laboratory beneficiation tests on a sample of scheelite ore and a sample of low-grade scheelite flotation concentrate from the Sangdong mine, Korea. Sangdong was the foremost producer of tungsten concentrates on two occasions - during part of World War II and in 1953. It was also a significant producer of bismuth concentrates. Resources are very extensive and could support a 5,000-ton annual output of tungsten concentrates for many years. Located in the eastern part of South Korea near the 37° latitude, Sangdong has been a vital source of dollar income for the Republic of Korea in recent years. Its shutdown in March 1954 came about as a result of the great decline of tungsten prices and the fact that a sales contract with the United States Government had been terminated, In addition to establishing new markets, the problem of reopening Sangdong will be related to cost reductions and improving mill recoveries. Large quantities of offgrade scheelite concentrates were produced in the past and shipped to the United States for further beneficiation. Other low-grade concentrates and middlings have been stockpiled or discarded at the mine plant.

Jan 1, 1954

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By Paul T. Allsman

This paper describes metal- mining practices at the Harrington -Hickory lead - silver - zinc mine at Milford , Beaver County , Utah . The operations of the Harrington-Hickory incorporate a number of features that should prove of interest and value to other operators of small mines . These features include employee participation in profits , a well- laid -out electrical system, adequate financing , a well - balanced equipment and supply inventory , a well - organized system of bookkeeping , adequate roads , and good management . As crude ore is shipped directly to smelters and mills in the Salt Lake Valley , close attention is paid to see that the ore is segregated by classes and treated where it can bring the greatest not return . A combination of these features has resulted in maintaining relatively low costs, considering the grade and size of ore shoots at a time , during and following the war , when equipment , supplies , and labor were costly and difficult to obtain . The period covered in this report includes two war years and two years following , from April 1, 1944 to June 30 , 1947 .

Apr 1, 1949

By E. J. Murphy

The Bureau of Mines developed a fast, reliable modification of the Griess-Ilosvay procedure suitable for field analysis for NO2 in the fumes from explosives. Known concentrations of NO2-air mixtures were analyzed for the nitrous acid or nitrite formed in the reaction with three Griess-Ilosvay-type reagents by diazotizing and coupling. Comparison was made of the Rider-Mellon, Saltzman, and Patty-Petty procedures; the three procedures are in agreement if sufficient time of contact between NO2 and the reagents is allowed. In experiments to obtain an accurate factor for converting NO2 to nitrite, overnight contact was allowed in order to be sure conversion was complete. The factor was found to be 75 percent with a standard deviation of ±3.2. Low and erratic results were found using either the Saltzman or Patty-Petty reagents as absorbing liquids unless several hours&apos; contact was allowed. If dilute NaOH solution was used as the absorbing liquid instead of a Griess-Ilosvay-type reagent, 92 percent of the overnight conversion factor was found after a 3-minute shaking time and a la-minute standby time. The Saltzman reagent was preferable for fieldwork with the dilute NaOH solution as the absorbent because of its easy application, rapid reaction, and intense color even at low NOB concentrations.

Jan 1, 1967

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By William R. Vogel

The Bureau of Mines Information and Analysis organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 3291, to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1989

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By Clinton C. Knox

The Townsite mine, consisting of 40 acres in the town of Cardin, Okla., is in the center of a highly productive part of the Picher-Cardin district of the Tri-State zinc and lead field. Previous to the time of the work done by the Bureau of Mines, the property had been partly explored by churn drilling, and an area-of about 8 acres in the southwestern corner had been exploited by underground workings. The Bureau of Mines investigation had as its object the more intensive development of the northern part of the property where previous drilling had indicated a possible ore deposit of commercial grade. Churn drilling by the Bureau began in September 1942 and continued to February 1943. Twenty holes totaling 4,827 feet of bore were completed. Utilizing the information gained from these drill holes, the Weidman Mining Co., lessee of the tract, sank a shaft and proceeded to the exploitation of the indicated ore bodies.

Jan 1, 1949