Search Documents

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By Y. S. Song

Flotation separation of galena, sphalerite with pyrrhotite in ethanoic acid + sodium acetate sys-tem was studied in this paper. The flotation tests show that galena and sphalerite can float but pyr-rhotite can hardly float in the pH range of 3.6 to 5.6 in ethanoic acid + sodium acetate system. The flotation tests also show that galena can be separated efficiently from pyrrhotite and sphalerite can be separated on the whole from pyrrhotite, but the separation efficiency of the former is much better than the latter. The flotation results have been investigated by ultraviolet spectrum and XPS analysis, and explained by theory of hard and soft acid and base (HSAB), hydrogen bond and galvanic coupling.

Jan 1, 2014

By V. V. Musaev, A. M. Klyushnikov, R. R. Galimov

"A study was made of chemical and material compositions of the oxidized gold-bearing ore of the Kochkovskoe deposit. It was demonstrated that examined ore consisted mainly of quartz, carbonate and feldspar with a gold content of 2.2 g/t and a silver content of 6.1 g/t. By means of agitation leaching tests it was founded that about 79-80 % of gold can be extracted from ore using cyanide leaching solutions. The achieved high-speed dissolution rate of gold was due to its presence in a finely dispersed state (less than 2.73 µm), which was confirmed by the research of Uralmekhanobr. It was proposed that the ore can be processed by heap leaching process using cyanide leach solutions. Technological studies on the modeling of the heap leaching process were initially carried out in percolators with a capacity of 5 kg on agglomerated ore. It was preliminary established that agglomeration should be carried out at a cement consumption of 12-16 kg/t, with the moisture content in pellets reaching up to 10-12 %. The best percolation leaching results can be obtained with ore crushed to the size of -20 mm. The maximum extraction of gold to the solution was 79-80 % while the L:S ratio reached 1.2-1.4:1.In cooperation with the research center of OJSC ""Berezovsky mine"" a semi-industrial heap leaching test was accomplished. The result of a test performed was an extraction of 78.5 % of Au and 21 % of Ag from ore to a pregnant solution. This extraction degree was achieved at a L:S ratio 0.9: 1. On the ground of results obtained, a technical regulation was developed for design of the heap leaching plant with the capacity of 500 thousand tons of ore per year.INTRODUCTION The ore of the Kochkovskoe deposit represents an important reserve of gold in the Zabaikal region. Of the upmost interest are oxidized ores, the processing of which can be carried out by heap leaching (HL) with cyanide solutions. The purpose of this work was to study the composition and to develop a technology for heap leaching of oxidized ore."

Jan 1, 2018

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By A. S. Chekmarev, T. Z. Lygina, K. G. Egorova, A. V. Skvorcov

"We have conducted analytical and technological evaluation of sepiolite containing clay. The possible areas of application of the sepiolite have been investigated and complex methods of enrichment of natural sepiolite have been identified. It was determined that for preserving the structure of minerals after processing the most effective method of the natural agglomerates disintegration was the soft abrasion of the clay fraction up to 0,5 mm. Disintegration of sepiolite clay along with using high energy-stressed effects on the matrix can deteriorate the rheological properties of clay suspensions and reduce the yield of drilling mud and sorption properties. To improve the quality of clay powders we used combined gravity-modifying method of wet enrichment. After the wet enrichment the yield of drilling mud increased up to 12.7 m3/t, with the addition of MgO up to 20,3 m3/t. It was noted that drilling muds contenting more than 50% of sepiolite are stable in mineralized (salt) waters. Based on the studied activated sepiolite rocks we obtained the effective heat-insulating materials with relatively low thermal conductivity – 0,165 W/m·K, average strength – 7,29 MPa and water absorption-49,0%.INTRODUCTION The modern development of the Russian economy requires the implementation of scientific and technical tasks. The solutions of it involves a radical reduction in energy, heat losses and material consumption of products, rational and efficient using of all types of resources, as well as the using of new types of mineral raw materials and materials based on it. An example of a new type of mineral raw materials for Russia is sepiolite containing rocks, due to unconventional conditions for their soils accumulation in the climate of the Far North. Sepiolite is a unique type of nonmetallic mineral. It is formed in soils, marine and saline basins, occurs in carbonate and carbonate-clay rocks in the form of lenses and lens – shaped layers, rarely nodules, loose powdery masses, shell-like concretions. Sepiolite may have a soft porous macroscopic appearance or less often the structure of the fibrous mass. Color of sepiolite is from white to cream with gray, green, pink and even crimson shade depending on the degree of pollution. Sepiolite can be in two forms - a-sepiolite (parasepiolite), which occurs in the form of large packets of crystalline fibers and ß-sepiolite, which occurs in the form of amorphous aggregates or small flat rounded particles. The sepiolite fibers have a length of from 0.2 to 2 Å, width from 100 to 300 Å, the thickness from 50 to 100 Å (Geological dictionary, 1973)."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By S. Jagdish

India ranks fourth in the world of iron ore production and exported 55% of the total iron ore production of 180.9 million tons in 2006-07. As per United Nations Framework Classification (UNFC), the total iron ore reserves in India is 25249 mt. This consists of about 14630 mt of Hematite ore and 10619 mt of Magnetite ore. While the deposits of magnetite iron ore are limited to the states of Karnataka, Andhra Pradesh and Tamil Nadu, hematite ore is available in abundance in Jharkhand, Orissa, Chhattisgarh, Karnataka and Goa. National Steel Policy, declared by government of India in 2005 envisages 110 million tons of steel production by 2020. This is likely to be revised upwards. Massive exploration work in iron ore is needed to convert the available resources of iron ore into reserve category. Steel Authority of India Limited (SAIL) produced more than 24.5 million tons of iron ore during 2006-07 and plans to produce 42.0 million tons per year by the year 2010-11 to meet the requirement for a hot metal production of 26.2 million tons. While processing iron ore, the challenge faced would be the reduction of the gangue materials ? alumina and silica. It is proposed to bring down alumina and silica in the iron ore to less than 2% each from the current level of 2.5%~3.5% each. Appropriate beneficiation schemes are being developed depending upon the mineralogical characteristics of iron ores at different mines in the country. The state-of-art beneficiation technologies like Hydro-cyclone, jigging, magnetic separation etc. will be incorporated. SAIL?s corporate plan envisages blast furnace burden of 15% iron ore lumps, 15% pellets and 70% sinter by 2010. This strategy opens up the opportunity of utilization of micro fines generated in the mining and beneficiation processes for pellet making. This also directs towards all together new technological approach to the beneficiation process. SAIL is planning to set-up three pelletisation plants of 2~3 mtpa capacity. Environmental issues like reduction in slime loss and utilization of dumped low-grade iron ore are very important. R&D Centre for Iron and Steel, SAIL has carried out extensive laboratory investigations in the above area. This will help in reducing the loss of valuable iron through slimes and also increase the iron ore resource base. Laboratory investigations indicate that low grade dumped ore fines with Fe: 55.5% can be upgraded to a product with Fe: 66.2% with about 48% recovery.

Jan 1, 2014

By G. Prabhulingaiah, D. M. R. Sekhar

"A phosphate deposit of estimated 6 billion tons of P2O5 is located 180 to 300 meters below the sea level, 185 kilometers north of port Luderitz, Namibia. The ore bed is 6 kilometers wide and 220 kilometers long. The ore deposit analyzing 16% P2O5 is loose sediment of 1.5 meters thick without over burden. Sizing of the ore to - 1.4 mm + 0.150 mm improves the grade to 23.54% P2O5 with a P2O5 recovery at 83.75% containing phosphate pellets and flakes of sea shells. Clay, bacterial debris as organic matter, flakes of broken sea shells and fine phosphate containing particles report to - 0.150 mm fraction and + 1.4 mm fraction contains sea shells and few phosphate containing pellets. The mineralogical composition of phosphate containing pellets is estimated (Droste, T.C., 2004) 80% frankolite, 6% pyrite, 4% illite, 3% quartz, 3% amorphous SiO2, 1% carbonates, 1% organic carbon and = 1% ilmenite, magnetite, zircon etc. The phosphate content in the pellets is around 27.7% P2O5. Trials to separate by gravity or flotation processes were not successful. Leaching of carbonates (sea shell flakes) under mild acidic condition (= 2% acetic acid or HCl solutions) or calcinations followed by leaching however yielded residues (concentrates) of grades 27.85 - 32.74% P2O5 at P2O5 recoveries ranging from 78.45 - 96.8% P2O5."

Jan 1, 2014

By Thomas Mütze, Petya Atanasova, Kai Bachmann, Urs A. Peuker, Thomas Leißner

"A method is presented for the evaluation of mineral processing by liberation and upgrading. The method bases on the plot of recovery of valuables versus the recovery of gangue (Fuerstenau upgrading curve). The locking curve of a feed material was plotted together with the upgrading curve in a Fuerstenau diagram. The assessment of liberation and upgrading is done by a comparison of surfaces formed by the curves and some characteristic lines of the diagram. This plot allows the calculation of two new quantitative measures for liberation and upgrading. Both parameters can be combined to a third parameter describing the quality of the whole technical setup for mineral processing by subtracting the upgrading parameter from the liberation parameter. The third parameter shows a positive value in cases of upgrading determined processes, a negative value in cases of liberation affected processes and about zero for processes affected equally by liberation and upgrading. Thus it is easily possible to distinguish between poor results in the mineral processing caused by insufficient liberation or poor results caused by insufficient upgrading. Preliminary results from two case studies, performed on two different ore types, are very promising illustrating the practical use of such an approach."

Jan 1, 2014

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By G. P. Wong

"In the Inco matte separation process, a slow-cooled converter matte is separated into three main discrete mineral phases: chalcocite (Cc), heazlewoodite (Hz) and a Cu-Ni-Fe alloy. After magnetic removal of the alloy, Cc and Hz are separated by flotation at pH>12 with diphenyl guanidine (DPG) as both collector and frother. High selectivity is achieved in rougher flotation. However, in later flotation stages such as in the middlings circuit, as oxidation takes place, Hz becomes highly floatable, resulting in a very poor separation between Cc and Hz.Starch and dextrin as Hz depressants were evaluated on the middlings circuit feed and showed no positive impact on Cc/Hz separation selectivity. Ethylene diamine tetra-acetic acid (EDTA) extraction showed the existence of abundant surface Cu and Ni ions. The use of triethylene triamine (TETA) or EDTA in flotation did not improve Cc/Hz separation selectivity. Microflotation tests were carried out on pure synthetic Cc and Hz minerals. It was found that Hz did not float in the presence of DPG. However, Hz conditioned with either copper sulfate solution or in contact with Cc floated readily in the presence of DPG. It is concluded that the major reason for Hz flotation in the middlings circuit is due to Cc oxidation releasing Cu ions that adsorb on the Hz surface making it reactive with DPG thus rendering the Hz floatable."

Jan 1, 2003

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By X. Q. Cao

As the second largest phosphate resource in the world, Chinese phosphate ores generally grades with low of P2O5. The presentation of beneficiation test on the low grade of phosphate rock in this paper may be used for a reference for development and utilization of the similar reserves. The ore is a marine sedimentary phosphate rock containing low grade of P2O5 and high content of MgO and R2O3; The banded structure shows its suitability for heavy medium separation. The laboratory heavy liquid testing results indicate that as specific gravity of the heavy liquid is 2.85 g/cm3, a rougher concentrate assaying 28.71% P2O5 could be obtained while the rougher tailings contain only 4.47% P2O5. When the combined process with heavy liquid separation followed by direct & re-verse flotation is employed to treat the feed containing 21.15% P2O5, 3.79% MgO, 1.86% Fe2O3, 3.66% Al2O3, 23.75% A.I, and specific gravity of heavy liquid is 2.84 g/cm3, the optimum mesh of grind is 67.5% minus 200 mesh, a phosphate concentrate contained 32.51% P2O5, 0.48% MgO, 0.81% Fe2O3, 1.69% Al2O3 can be produced at a yield of 55.24%. The concentrate P2O5 recovery is 85% with which quality comply with the Class A specifications for production of phosphate fertilizer.

Jan 1, 2014

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012