Search Documents

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

The present work aimed to verify the possibility of using froth flotation to separate the constitu-ent minerals of an alaskite rock waste having as the main minerals quartz and feldspar. Three stages of tests have been carried through. In the first stage was used an amphoteric collector for flotation, diaminedioleate, at pH 2 and, after analyzing the final products, a very poor selectivity was ob-served. During the second stage of tests, different collectors that are normally used for feldspar flo-tation as amines, sulfonates and soybean oil were employed. Once more, it was not possible to reach reasonably selective results. In the third stage, a salt of etheramine was used for collecting the feldspar and hydrofluoric acid was utilized for controlling the pH. A simulation of three flotation steps (rougher, cleaner and recleaner) permitted to attain a good selectivity in the flotation process. A concentrate with a silica content of 96.6% was obtained. The low concentrate content of alkalis totalizing 0.52% and a feldspar recovery of 96.5% to the tailings, represented by the high content of Na, K, and Al2O3 in the tailings, demonstrated that the concentrate was made up mostly of quartz.

Jan 1, 2014

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By Jorge Menacho

"A typical Chilean producer in the Large Copper Mining Industry today is characterized by high production level with economical results decreasing but still attractive. Operational activities are developed within a low-productivity environment, with high cost and complex relationship between the company and communities, government authorities, providers, clients and their own workers. Decreasing copper grades and limited availability of energy, water and workforce are structural problems which require the State intervention in collaboration with the relevant actors and benefits would be evident in the middle or long term. Main opportunities in the short term are found in the sub optimal conditions we have at many plants today. Robust solutions to control existing operational management system as well as to supply systematic optimization options are needed. These should be oriented toward effective fulfillment of specific operational set points and also to reduce variability in crosscutting tasks. Solutions should include easy connectivity to existing information systems as well as to a suite of simulation and optimization tools settled in a highly interactive communication platform. Relevant issues include minimization of specific energy and fresh water consumption, maximization of the use and performance of critical equipments, minimization of damage to environment and control of effective application of good operational practices. Several specific examples are given."

Jan 1, 2014

By M. Marinov

The Bulgarian deposits of quartz-kaolin raw materials are localized in the NE Bulgaria. For many years, the quartz-kaolin sand separation has been performing by water washing technology. After wet separation the raw material yields two products ? washed kaolin (different grades) and quartz sand (different grades). Research and development program has started to improve the quartz-kaolin sand separation. The program has undertaken an increasing of processing capacity, to decrease the losses in the tailings and to provide production of new quartz sand grades. The kaolin-silica raw materials from Vetovo open mine and the technological tailings from Vetovo processing plant were characterized. It was established that there are a lot of losses of quartz in final tailings. New approach on kaolin-silica raw material separation was tested in laboratory scale. The test work was performed on Derrick Stacksizer screening machines. The results of laboratory experiment show that there are possibilities to increase the quartz sand recovery and to start the production new grade sand. The full-scale pilot test was performed including the following units: two Derrick Stacksizer screening machines equipped with 0.430 mm and 0.150 mm opening Derrick Urethane Panel, respectively; Flat bottom DN 500 Hydrocyclone and DN 100 Hydrocyclon. The pilot test data clearly demonstrate that the Derrick Stacksizer screening machines are suitable for Bulgarian silica-kaolin raw material. Based on the test data a new quartz-kaolin separation technology was developed. The new technology was introduced in Vetovo processing plant increasing processing capacity and decreasing the losses of quartz in final tailings. Additionally the production of silica sand grade PK 0.16 is increased and starts the production a new grade PK 0.10.

Sep 1, 2012

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By Song Z. Guo

Calcite and magnesite are both carbonate minerals and their crystals belong to trigonal system. Flotation tests were carried out to investigate the flotation behaviors of calcite and magnesite. The test results show that the floatability of calcite and magnesite under different grinding environment had obvious differences. The floatability of calcite using sodium oleate as collector after dry grinding is better than wet grinding, but the floatability of magnesite after wet grinding is better than dry grinding. The XPS surface elements test and zeta potential measurement show that, wet and dry grinding process makes the distribution difference of surface anion and metal cation, then influence the floatability of the two carbonate minerals using sodium oleate as collector. Difference of the carbonate crystal structure and solubility properties was also investigated. Research shows that crystal structure difference of calcite and magnesite causes the difference of solubility, which can influence the flotation behaviors under different grinding environment. Keywords: carbonate mineral, crystal structure, solubility properties, flotation, surface character

Sep 1, 2012

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014

By W. S. Eu

Thermal treatment of mineral ores can initiate thermal phase transformations which can affect either their activation or deactivation, subsequently influencing their ability to dissolve in a leaching reagent. The formation of rutile and hematite from ilmenite minerals, for example, has been suggested to occur through a series of reduction and segregation reactions. This process has been used in beneficiating low-grade weathered ilmenite ores to higher grade rutile. Despite decades of re-search, the mechanism of this process is not well understood, because dissolved intermediates are poorly crystalline and are difficult to quantify, with the exception of the final rutile products. Previous studies have shown that disrupted intermediate phases, by thermal treatment, are most susceptible to reagent attack and can often demonstrate ?activation? effects. In this study, synchrotron based X-ray diffraction method was used to investigate in-situ and in real-time the transformation of ilmenite minerals to rutile and hematite during calcination. The rate of formation and disappearance of specific Bragg peaks during the reaction and thermal decomposition of the mineral were used to derive an understanding of the solid-state reactions. The effects of the mineral transformation were validated by laboratory based batch calcination and leaching in sulphuric acid. The results suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By A. Yörükoglu

In this study, thorium mineral that found in the complex ore deposit bearing bastnasite, fluorite, and barite from Eskisehir - Sivrihisar district has been tried to extract by using HCl and H2SO4 leaching. Ore sample of approximately 3 tons taken from the ore deposit has been homogenized in order to obtain composite samples by means of ore preparation techniques for experiments. Results of chemical analyses of composite samples are as given; 40.8% CaF2, 35.35% BaSO4, 2.01 Ce, 1.5% La, 0.39% and 0.1% Th. HCl and H2SO4 leaching processes have been performed to gain Th in the ore. For determining the optimum particle size, the samples have been ground under controlled conditions and brought to the sizes of 0.065, 0.2, 1 and 3 mm. Leaching experiments have been carried out in both HCl and H2SO4 acids without roasting and roasting at the temperature of 900°C for 1, 3 and 6 h retention times for all particle sizes determined before. In the experiments, the highest Th recoveries reached are as follows; 78.74% Th when H2SO4 and 1 mm particle sized sample used, and 1 h roasting applied and 73.38% Th when HCl and 1 mm particle sized sample used, and 3 h roasting applied. Keywords: thorium, leaching, concentration, sivrihisar, roasting

Sep 1, 2012

The status of utilization of copper ore resources, and the application and development of biohydrometallury technology in the world is reviewed. Based on the characterization of Zambia?s copper resources, biohydrometallurgy technology is shown to be a practical approach to extract and utilize the enormous low grade copper resource, such as ore tailings and low grade copper ore in this country. Through the cooperation of CSU, China and MMMD, Zambia, ?CNMC-CSU Demonstration Base of Biohydrometallurgy Technology in Zambia? was launched and several biohydrometallurgy plants are being constructed. This indicates that the biohdyrometallurgy technology would be applied soon in Zambia and in the whole Africa. Biohydrometallurgy technology stands as an efficient alternative to the traditional pyrometallurgy process and it can be the key to unlock mineral resources value. Keywords: biohydrometallurgy, low grade copper ore, Zambia, Central South University

Sep 1, 2012

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014