Search Documents

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division's Toronto meeting in April, 1960. In bringing the power engineer's viewpoint to the coal producers' attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the 'nineties', probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By John Folinsbee, Brian Danyliw, Tony Y. Chong

"Control of fugitive dust has become increasingly important in the mining industry both from a health and safety and environmental standpoint. Mining operations in particular have required improved fugitive dust control due to recent lowering of the allowable airborne silica concentration to which workers can be exposed. Experience has now proven that the implementation of a surfactant based chemical dust suppression system can enhance existing mechanical dust control methods resulting in much more efficient control of fugitive dust.The Porcupine Joint Venture (Dome Mine) utilizes dry secondary crushing and screening that makes it particularly prone to fugitive dust emissions. A variety of potential dust control systems were evaluated and this led to the installation of a surfactant based water spray system to augment the existing mechanical dust collection systems.A great deal was learned through the implementation of this system. This paper describes the entire process, from testing, system design and installation, through optimization and standardization of operation. In addition a variety of problems were identified, and innovative solutions were provided. Also, the metallurgical impacts on down stream processing are highlighted. Finally, a full discussion of overall results including a discussion of the relationship between silica and total dust concentrations is included."

Jan 1, 2005

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By Gerry Doeksen

The paper deals with three case studies: (a) the handling of wet concentrates (5 to 8 per cent moisture) through feed bins; (b) the handling of the same product in rail cars; and (c) the handling of dry concentrates (less than 0.5 per cent moisture) through feed bins. In each case, the paper discusses the problems of rat-holing. In each of cases (a) and (c), there is a discussion on the consequent extreme variations of feed rates coming from the feeders, making automation of process control difficult to impossible. Currently available bin-flow theory and flow property tests are used as aids in redesigning the bins. The paper concludes with illustrations of the final results after the redesigned hoppers were installed and tested. There is also a discussion on the advantages of the new mass-flow bins on adjacent feeder performance.

Jan 1, 1970

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By George P. Demopoulos, Nima Parsi Benehkohal, Marianna Uceda

Lithium-ion batteries (LIBs) find wide range of applications from portable electronics to electric cars and stationary storage or renewable energy. LIB electrode fabrication is done through mixing the active material (Li-ion host) with carbon (conductive component) and polyvinylidene fluoride (PVDF), which acts as a binder. These components are dissolved in N-methyl-2-pyrrolidone (NMP) to form a paste which is then doctor bladed onto the aluminum current collector. NMP is a toxic chemical and the overall fabrication process remains costly. Efforts are made of eliminating NMP by (1) replacing the binder and (2) using a new fabrication method. Of particular interest among these new methods is electrophoretic deposition (EPD). Via the application of DC potential, particles in suspension can be electrophoretically deposited on different conductive substrates in a relatively fast rate rendering EPD feasible for industrial application. A key aspect for successful application of EPD is the formulation of a stable suspension. Within the McGill HydroMET group, we explore the potential of EPD in fabricating LIB electrodes having demonstrated its effectiveness in the case of P25 nanotitania/carbon anodes. The performance of EPD fabricated TiO2/C electrodes is compared to standard PVDF-based electrodes and shown to have comparable charge capacity. This method is now being extended to other electrode materials. In this paper an introduction to the EPD method will be made and subsequently its use in fabricating LIB electrodes will be described. The performance of the fabricated batteries is evaluated via galvanostatic charging/discharging and cycling tests.

Jan 1, 2016

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By G. J. S. Govett

World mineral production is dominated by six countries - the U.S., the U.S.S.R , Canada, South Africa, Australia and China - which also hold most of the reserves of the world?s minerals. For the developed and centrally planned countries, there is a strong positive correlation between the mineral production of a country and its land area: there is no correlation between mineral production and land area for the less developed countries. These facts imply that, after taking due account of geological controlling factors, a country may expect to produce minerals in approximate proportion to its land are a provided that political, economic, and historical factors are conducive to mineral exploration and mining. Contrary to popular political belief in many parts of the world, the developed countries are the major source of mineral imports for the industrialized countries. Moreover, exports of ores and minerals account for a relatively small par t of world trade, and are an important factor in the export picture of only a few of the less-developed countries. The looming resource confrontation between the developed and the less-developed countries is based largely on the false premise that the industrialized countries of the world are minerals-poor and owe their wealth to cheap minerals from the less-developed countries. The data presented refute this. Geological controls are relatively minor in the present distribution of world mineral production; political and economic factors are dominant. It is argued that an expansion of world trade in minerals - based on increased exploration and new forms of finance for mining ventures - rather than cartels, price-fixing and trade restrictions is by far the preferable solution to the problem of redressing the legitimate grievances of the poor countries of the world.

Jan 1, 1977

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By A. S. Dawson

Introduction The purpose of this paper is to discuss, in a general way, the application of geological principles in the exploration for, and development of, deposits of industrial minerals. Mention of geological factors pertaining co specific minerals will be by way of illustration only. Since many prospectors are little acquainted with the geological setting and mode of occurrence of deposits of these minerals, some prospecting possibilities in the field will be pointed out. Geology is a tried and proven tool in the search for and exploitation of metalliferous deposits and of oil and gas fields, but, so far at least as Canada is concerned, only very rarely has a directed, intensive search been made for deposits of industrial minerals. Examples might be cited, however, where, in other countries, such investigations have yielded rich rewards. Thus, development of the vitally important potash deposits of New Mexico was the result of a deliberately planned programme of geological investigation, first by United States Government agencies, and later by private interests. War or the threat of war, or peace-time industrial expansion, can render concentrated exploration for specific minerals desirable or even essential. Such exploration is, primarily, a geological problem. Admittedly, there is in general less scope for the application of geology in the search for, and development of, deposits of industrial minerals than of metalliferous minerals, oil, etc. Where the latter are concerned; the objective of exploration is to find a material that is valuable, within broad limits, no matter where it is located or how it occurs. The unit value of the material is limited only by the amount of the valuable constituent in the formation- its possible upper limit is tremendously high. On the other hand, many industrial minerals constitute in themselves 90 per cent or more of the formation- their amount cannot increase and their unit value is commonly low. Moreover, for commercial exploitation, the deposit must, in general, be reasonably close to markets or to plant or other facilities for processing the raw material, since, owing to its low value, this cannot be transported any great distance. As a consequence, intensive geological search for and investigation of such deposits has been restricted to industrialized areas. Obviously, however, it is good insurance for any operator to understand the geological background of his deposit, particularly in the case of new developments.

Jan 1, 1949

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By C. M. Anson

This paper describes the progresses used in the manufacture of steel wheel-centres, tyres and axles at the works of the Commonwealth Steel Products Co., Newcastle, N.S.W., Australia. The plant is adjacent to the Northern railway and consists of three main buildings, namely: the foundry, the forging and rolling shop, and the machine shop. The foundry contains a 6-ton Heroult electric furnace, together with all necessary mechanical appliances for moulding. Reheating furnaces, steam hammers and tyre rolling mill are installed in the forging shop. The machine shop contains lathes, boring machines, and hydraulic presses. Until this plant commenced operations all wheels used in Australia were imported, previ.ous to the war, from England and Germany, and latterly from England only. Besides being of great benefit to the country in that there is now a domestic source of supply of these articles, there is also the advantage of retaining the home market; and in addition, a small portion of the population are now engaged in highly technical occupations requiring a great degree of skill. The plant began to operate in October 1919, and by 1921 was in a fair way to meet the domestic demand for those articles of railroad equipment which it manufactures.

Jan 1, 1925