Search Documents

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By J. Gogal

Cameco's Cigar Lake Operation (CLO) started commercial uranium ore production in 2015. Initial mining was focused in areas of the ore body with relatively low concentrations of elements of concern (EOCs). As mining progressed into areas of the ore body that were richer in EOCs, some statistically significant behavior of certain analytes was noted in the water treatment circuits. It was ultimately found that the CLO ore body natively hosts numerous alkyl arsine compounds in addition to inorganic arsenide minerals. The alkyl arsines were found to be recalcitrant to typical adsorption on ferrihydrite, with the degree of recalcitrance associated with the degree of alkylation. A number of changes to the process circuits and water balance were performed and planned in order to inhibit the transport of alkyl arsines from the ore stream into the process water stream, and to optimize the overall site water usage. In some instances, the interactions of equipment in conjoined circuits of the process had controlling effects on the behavior of the overall circuit. Work continues to iterate upon the capital design features in order to further tighten the water balance, and to optimize water usage and operating costs.

Jan 1, 2020

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort' of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary's suggestion is just like that- much too comprehensive for any half-hour's presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary's query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By L. K. Daneshmend

The mine of the year 2020 will need to be based on a new way of mining. It will employ technology in a paradigm that assumes responsibility for sustainable development: taking account not only economic but also ecological and social issues. This will require a holistic approach to mine design and planning, considering all controlling factors and impacts (technical, economic, environmental and social). A national collaborative strategy is required to address the several options that exist for the development and application of 2020 mining technology. Key issues in implementing 2020 mining technology will also relate to human resources, in terms of employment, skills and education. A need exists to proactively prepare for 2020 through development of a comprehensive education and training strategy.

Jan 1, 1998

By J. G. Trowell, D. T. Magee

"IntroductionMANITOBA'S first recoverable oil was from the California Standard Daly 15-18 well in Lsd. 15, Sec. 18, Twp. 10, Range 27, W.P.M., completed early in 1951. This well also gave the first indications of commercial production in the Williston basin, which is centred in North Dakota and extends into southeastern Saskatchewan and southwestern Manitoba. Subsequent drilling in the Manitoba portion of the basin has revealed the presence of oil in more or less commercial quantities at various points in an area approximately four townships in width and eleven townships in length.Although completions are becoming fairlly widespread in the area,, the greatest activity is in the Virden district, with the focal point in the Daly field, approximately eight miles west •of Virden. This paper will deal with the various techniques used in the Daly field, where •completion problems have •been unusually troublesome. Techniques evolved there have already been used with success at other points in southwestern Manitoba.Daly FieldGeneralTo date, all production has been from the Mississippian limestone, which is encountered •at depths ranging from 2,300 to 2,500 feet. Pay thickness is •of the order of 100 feet. Core analyses indicate average porosity .of about 9 per cent but permeabilities, for the most part, are extremely low."

Jan 1, 1953

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By J. Kan

In order to determine the recovery functions in an oil sand circuit it is necessary to have more than a minimal determination the mass flows in the network. This over-determination is essential in order to allow for measurements within the flow matrix "to flex" according to an error function. It is then possible to identify the flows and composition at all points with maximum likelihood. These so-called full mappings are not easily obtained. However, in order to obtain an unequivocal determination of all the unit operations recoveries such a balance is needed. When databases are constructed exclusively with coherently balanced sets of data it is possible to obtain a maximally accurate process model by maximizing the probability of correctly identifying the process causality. Indeed, it is doubtful in cases of normal complexity that any sense can be made of data that is not so balanced. Coherent mass energy balancing is a tool developed by mineral processing scientists and engineers. Its rigorous application to oil sands is the subject of this paper. The additional element associated with hydrocarbon requires special considerations. It is shown that at least one currently available mineral processing tool will solve the full-mapping problem for an oil sand operation. Experimental design constraints are discussed in this paper relating to the development of databases for the development of effective process models.

May 1, 2004

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006

By H D. Smith

T HE production of coal in Canada was slightly higher in 1964 than in the immediate past, and the major users continue to be the electric utility and metallurgical industries. There are continuing trends toward the increased use of cokes and chars in various metallurgical applications. Geological Research During 1964, the coal drilling program of the Research Council of Alberta (RCA) was concentrated in the extreme south of the Province (notably in the Milk River area and the region immediately to the northeast of this area). Field work commenced on June 1 and was completed at the end of September, by which time a total of 376 holes, aggregating some 48,500 ft., were drilled in 132 townships. Although no new major coal occurrences were intersected, the pro-gram yielded useful data for defining the extent of the known coal deposits in the area. Detailed results will be analyzed during the winter and reported in due course. Meanwhile, a full report on the

Jan 1, 1965

By P. C. Benedict

Introduction and Summary The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, district of Thunder Bay, Ontario. Production started in March, 1934, and terminated in September, 1941. During this period, the mill treated 425,866 tons of ore, from which 153,103 ounces of gold were recovered. The lowest level from which ore was mined was the 1900, but considerable drifting was performed on the 2075 level and 800 feet on the 2415, the deepest level. The following description of the geology of the mine is recorded by the senior author but is based on the observations and complementary mapping of both authors. The vein strikes about N.72°E. and has an average dip of 80°S. (Figure 1). In stoped sections, the quartz averaged about two feet wide. On the 1725 level it was drifted on continuously for more than 7,000 feet, but in the mine as a whole practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section but not much beyond its limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth. It may be generalized, from top to bottom, as light grey to dark grey to brownish. The brownish quartz first appeared near the bottom of the ore.

Jan 1, 1947

By M. Rafiee

Indoor physical security, as a perpetual and multi-layered phenomenon, is a timeintensive and labor-consuming task. Various technologies have been leveraged to develop automatic access control, intrusion detection, or video monitoring systems. Video surveillance has been significantly enhanced by the advent of Pan-Tilt-Zoom (PTZ) cameras and advanced video processing, which together enable effective monitoring and recording. The development of ubiquitous object identification and tracking technologies provide the opportunity to accomplish automatic access control and tracking. Intrusion detection has also become possible through deploying networks of motion sensors for alerting about abnormal behaviors. However, each of the above-mentioned technologies has its own limitations. This paper presents a fully automated indoor security solution that leverages an Ultra-wideband (UWB) Real-Time Locating System (RTLS), PTZ surveillance cameras and a Building Information Model (BIM) as three sources of environmental data. Providing authorized persons with UWB tags, unauthorized intruders are distinguished as the mismatch observed between the detected tag owners and the persons detected in the video, and intrusion alert is generated. PTZ cameras allow for wide-area monitoring and motion-based recording. Furthermore, the BIM is used for space modeling and mapping the locations of intruders in the building. Fusing UWB tracking, video and spatial data can automate the entire security procedure from access control to intrusion alerting and behavior monitoring. Other benefits of the proposed method include higher accuracy and robustness, more complex query processing, and interoperability with other BIM-based solutions. A prototype system is implemented that demonstrates the feasibility of the proposed method.

Aug 1, 2013

By K. H. Concannon, K. I. Hindle

"The use of simulation modeling in the primary metals industry (including mining, smelting, and metals processing) is expanding as significant cost-benefits can be realized by companies employing capital intensive processes. The economic scale and complexity of operations found in this industry is well-suited to applications using this ""what-if' computer modeling technique, ranging from proof-of-concept projects to testing facility design or configuration, and determining resource requirements. More recently this technique is being used to support on-going planning and scheduling for operations using the simulation as the engine to derive the best schedule. With increased computer processing capability, deterministic models are now being developed to capture the workings of a production system or conversion process, allowing real-time monitoring and scheduling of these operations. This paper presents a sample of some recent discrete-event simulation modeling applications that demonstrate the capability and benefits of this technique in the primary metals industry. These include the use of simulation to support the long-range planning of underground mining operations; the modeling of a metals supply chain network that employs a multi-modal distribution system; the scheduling of a metals coil finishing process using a deterministic simulation model; and a more detailed description of the use of simulation to model furnace and converter aisle activities within a smelter operation in Northern Canada."

Jan 1, 2007

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By Fidelis T. Suorineni

The conditions for rockburst occurrence are traditionally identified as: high stress, high extraction ratio, strong brittle rocks, folding, faulting, and unfavourable excavation geometry. Based on a critical review of case histories, this paper identifies oblique loading of orebodies by the major far field principal stress as a cause of rockbursts. Orebodies subjected to this loading condition are termed orebodies in shear. Orebodies in shear are subjected to compressive and shear loads. The case histories presented unambiguously show that the magnitudes of the far field principal stress alone, and a knowledge of the conventional rockburst causing factors are not sufficient for mine planning and design. The orientation of the major far field principal stress, or for that matter the driving stress relative to the orebody axis, should be recognised as one of the causes of rockbursts. It is suggested that since stress orientation is an important factor, and orientations from stress measurements are so variable, orientations from stress measurement data be complemented with underground observations from borehole and excavation breakouts to determine the actual in situ stress orientation, whenever possible. Also stress modelling for the design of critical elements (pillars) should include a sensitivity analysis on the relative critical field stress direction. The paper emphasises that special attention should be paid to or

Jun 1, 2012

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015