Search Documents

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

The continued exploration of the major brown coal deposits of the Latrobe Valley has resulted not only in the discovery of huge additional reserves, but also in new concepts of the stratigraphy and structure of the coal seams in that area. The author sets out his interpretation of the new information which has become available over the last six years.A section of the paper is devoted to the quality of the coal. As the chemical composition of these brown coals has been discussed in some detail by previous authors, only the major constituents and the heat value of the coal are dealt with in this paper. Some of the variations in quality are related to the geological structure.The occurrence of underground water and its relation to open cuts is dealt with briefly.INTRODUCTIONThe Latrobe Valley Tertiary Basin is almost entirely covered by a layer of Post Tertiary sediments which mask the underlying rocks and their structures. As a result, the geological understanding of this area has had to await the comprehensive drilling campaign in search of brown coal, initiated by the Victorian Mines Department in 1917, and subsequently carried on by the State Electricity Commission of Victoria. The first detailed geology was published by Herman (1922), and this was followed some 25 years later by papers by Edwards, and later Thomas and Baragwanath, to which reference will be made later in this paper. Herman included a section on the geology of the Latrobe Valley in his book Brown Coal, which was published in 1952.Since that time a considerable amount of new information has become available from the continued drilling carried out by the Commission. In addition, geophysical work carried out by the Commonwealth Bureau of Mineral Resources has assisted in the defining of geological structures in the area.

Jan 1, 1960

By Schiller J. C, Both R. A

Base metal mineralisation occurs at several locations within the regionally metamorphosed Kanmantoo Group on the southeastern flank of the Mount Lofty Ranges between Kanmantoo and Strathalbyn, 50 km southeast of Adelaide. Sulphide mineralisation is of three main types (Seccombe et al, 1985):1. copper deposits, at the Kanmantoo and Bremer mines, South Hill prospect and several minor occurrences,2. lead-zinc deposits at Aclare, Wheal Ellen, Strathalbyn, St. Ives, Scott's Creek, and Glenalbyn mines,3. pyrite-pyrrhotite mineralisation of the Nairne pyrite deposit and many other pyritic schist units within the Kanmantoo Group.Syntheses of folding, metamorphism and stratigraphy of the Kanmantoo Group were given by Kleeman and Skinner (1958), Offler (1960, 1963), Offler and Fleming (1968), Marlow (1975), Mancktelow (1979) and Parker (1986). Studies of the general relationships of mineralisation to structure in the Kanmantoo area were given by Grasso and McManus (1954), Mirams (1962), Poole (1969), and Lindqvist (1969).Several conflicting views on the origin of mineralisation in the Kanmantoo Group have been proposed. Thomson (1975) considered much of the mineralisation as a late-stage product of regional metamorphism and he, like Parker (1986) and Lambert et al (1987), stressed the importance of major lineaments as an ore control. However, Lindqvist (1969) and Verwoerd and Cleghorn (1975) tentatively suggested a syn-sedimentary origin to the Kanmantoo copper deposit and Jensen and Whittle (1969) and Seccombe et al. (1985) on the basis of sulphur isotope data proposed a bacteriogenic sulphur source and a sedimentary origin for sulphides in the Nairne pyrite deposit. The latter suggested that most copper deposits represent stockwork, vein or disseminated zones within subsurface vents whereas massive mineralisation at Wheal Ellen and Aclare mines probably accumulated on the ocean floor.This paper presents new geological information on the structural and metamorphic setting of the base metal deposits and attemptsto relate this information to previous regional studies of the Kanmantoo Group. Estimates of pressure and temperatureof peak metamorphic conditions based on silicate mineral stabilities are considered in relation to various silicate and sulphidegeothermometers which have not previously been applied to rocks in the Kanmantoo Group.

Jan 1, 1988

By A Jurg, F Leclercq

The total drill and blast concept is widely known in the mining industry. On the contrary, the quarry industry rarely adopts such working methods. Based on the experience of the CBS quarry in the North of France, this paper shows how up-to-date blasting technology and simple control methods can significantly improve the overall Mine to Mill efficiency of a quarry. The CBS quarry, in partnership with the EPC group and Nitro- Bickford Company, adopted a new working process three years ago aimed at increasing blast performance and related productivity of the downstream process (loading, hauling and crushing). The pattern geometry of each blast is controlled and explosive charging is carried out following the æconstant specific energyÆ CSE concept. This method provides a homogeneous fragmentation distribution and reduces vibration peak-particle-velocities. The impact on downstream productivity is controlled by means of a simple information management system, which collects and measures key parameters of the production process such as; hauling cycles, crusher throughput, secondary breaking and vibration peak particle velocity. This information system has clearly proved over time that consistent blast quality could be achieved, leading to a 30 per cent improvement in quarry productivity. Improved energy control of blasting through optimisation with electronic detonators, allowed a significant reduction in vibration impact on the environment. Improvement in blasting security, reduction in the environmental impact and productivity enhancement are major benefits that quarries can obtain from these CSE optimisation blasting methods.

Jan 1, 2007

Hydraulic transport of coal has been used for many years on the West Coast of New Zealand to extract small blocks of steeply dipping coal. Recent development at Strongman 2 Mine has seen the use of high pressure monitors to cut coal and a corresponding increase in the scale of production.This paper provides a brief introduction to hydraulic mining, describes the present system used at Strongman 2 and discusses future potential development.

Jan 1, 1998

By J Brisebois

The derelict Lake George Mine is located at Captains Flat in NSW, acommunity of approximately 450, which lies some 43 km southeast ofQueanbeyan. It straddles the Molonglo River, which flows toQueanbeyan and thence the nationÆs capital, Canberra. Catastrophictailings dam failures in 1939 and again in 1943 resulted in the transportand dispersion of thousands of tonnes of sulfidic wastes downstream,with terminal settling in Lake Burley Griffin, in Canberra. The mine wasclosed in 1962, and major rehabilitation in 1996 - 1997 addressed the riskof further collapses, and reduced water flow into the underground mine.Nevertheless, acid mine drainage from the mine, and seepages ofcontaminated water from the capped tailings dumps continue to pollutethe Molonglo River for some 30 km downstream.Environmentally, the highest contributor to the total contaminant loadof the river is the Main Adit Spring. This was shown to be a constantgroundwater-driven acidic flow, with contaminant generation resultingalmost entirely from the ingress of gaseous oxygen into the undergroundworkings. Long term remediation may be possible at source, by pumpingreducing gases into the sealed mine, but the probability of thistechnology succeeding to the required degree is yet to be demonstrated. For at least the medium term, treatment of contaminated water flow(s)will be required to achieve any of the water quality targets that may beapplicable to the river. Three methodologies were short listed, but anumber of strategic uncertainties remain, which the NSW Derelict MinesProgram will address. Future risk arising from long-term contaminantrelease by the treatment wastes must be considered. Appropriate data,and realistic long-term performance parameters regarding the relativestabilities of water treatment sludges are scarce, and make properevaluation of competing technologies problematic.

Jan 1, 2003

By Dyne GD

From experience in the design and operation of power station combustion facilities in most mainland Australian States, involving a wide range of black coals and lignites, and in the specification and procurement of coal supplies for power station use, techniques for the optimisation of coal resource development and power generation utilisation have been developed to ensure compatibility between characteristics of the selected coals and power station design. These techniques include computer data bases for resource data handling and computer simulation of coal-fired boilers for determining coal property cost effects. Data Base Systems allow results of coal analyses to be efficiently handled, to assist in the review of the relevance of resource data to the coal sections proposed to be mined and the coal fractions proposed to be marketed. Data Base Systems also facilitate the marshalling of coal quality data into basic utilisation format to enable a proper utilisation review and analysis of the certainty and scatter of coal properties. Computer simulation of the effects of different coal properties on the capital and operating cost of power stations is achieved by establishing conceptual design parameters of the major items of plant to relate the variations in coal specification to equipment size and type. Variations in power station budget costs can then be determined using the computer model for variations in coal specification.

Jan 1, 1983

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

Production implications of the introduct- ion of electric L.H.D. units in sublevel open stoping and pillar recovery at Rosebery are covered by Faulkner (1982) and Carlton (1982). The following engineering aspects associated with the decision to introduce electric L.H.D.'s are considered here: - Initial requirements for commissioning, including power reticulation at an adequate level to all operating areas. - Conversion of a manual system to radio remote control. - Maintenance backup requirement to ensure that the production potential is realised.

Jan 1, 1982

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984

A co-operative research project, combining Commonwealth Scientific and Industrial Research Organisation (CSIRO) research scientists findings and company iron ore geologists' expertise, resulted in new concepts about the origins, distribution and complexitie of iron ores and their parent rocks (banded iron-formation or BIF) in the Hamersley Iron Province of Western Australia. Understanding these problems was important to the efficiency of exploration, development and ultimate mining of iron ores. This genetic model, based on a detailed mineralogic background, was modified by Mt Newman geologists to obtain a user oriented classification for practical application in the field.The proposed Pilbara Iron Ore Classification (PIOC) gives iron ore geologists a basis from which to understand, identify and record the various mineralogic and physical characteristics of the many genetically different ore types occurring within and between orebodies in the Pilbara. More definitive quality control over ore products can be achieved based on the detailed understanding of ore types which the PIOC allows, compared to current classifications which deal only with the physical nature of ores. Of equal importance, the classification remains sufficiently simple to enable owners, operators and buyers to achieve a basic appreciation of ore type variations.With little modification, it is believed the classification has applications beyond the Pilbara, to iron ore worldwide.

Jan 1, 1984

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

By Y Gu

The Mineral Liberation Analyser (MLA) employs the technologies of scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The use of backscattered electron images to define phase boundaries produces very high resolution image analysis and subsequently detailed and accurate particle images and data output. The mineralogy, elemental deportment, grain size, liberation characteristics and mineral associations of a large number of samples can be described. The MLA uses a comprehensive set of analysis methods to meet a wide range of applications. The data from ore characteristion projects completed during feasibility studies are important aids for effective plant design. The MLA can be used to establish variation in the mineralogy of an orebody, identify and quantify the deportment of deleterious elements, and provide valuable information to support comminution and flotation test work. In established plants the MLA data is an important component of plant survey work and monthly composite samples. Changes in feed characteristics and/or operating conditions can be monitored and solutions to any deterioration in recovery and grade performance found. The MLA has extensive applications in the minerals industry. Rare and precious metal samples can be accurately measured using high-resolution grey-scale images. Several new measurement techniques have been developed to perform rapid searches of a large number of samples to provide efficient and accurate analyses of fine-grain, low concentrate material. Quantifying the mineral variability in mineral sands operations is essential to maximising grades and recovery. The MLA produces particle-based data on density, mineralogy, size and shape and has developed measurement techniques to provide the elemental quantification required for the characterisation of these deposits. Nickel sulfide ores can be analysed to provide modal mineralogy, elemental deportment and liberation and locking data. The low-grade and variable nickel mineralogy of these deposits makes the use of quantitative mineralogy an essential component of maximising returns. Coarse particle measurements preserve the in situ textures of ores and support flotation and breakage test work for feasibility studies. The deportment of penalty and bonus elements can be quantified and the association and grain-size data can be used to identify potential separation issues.

Jan 1, 2006

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

Before presentIng my address I wish to acknowledge the honour which has been conferred on me by my appointment to the position of President of the Australasian Institute of Mining and Metallurgy.It is a matter of great concern to us all to find our Empire at war. I am confident that, as was the case in the war of 1914-1918, members of this Institute and of kindred Institutes and Associations will contribute in full to the Empire's needs and that in the end our cause shall triumph.I think it appropriate that I should take as the subject of my address that of the Broken Hill Lead-Silver-Zinc Industry. The subject matter of this address has been confined to the operations of Mining, Ore Dressing, Lead Smelting and Refining and production of Electrolytic Zinc in Australasia. The review of the Broken Hill Lead-SilverZinc Industry would not, of course, be complete without reference to those Australian industries which trace their origin to the Broken Hill field, but· it is thought that an outline of these industries would make thIs review too extensive.HISTORICALMany efforts have been made to translate the early history of Broken Hill and its subsequent growth throughout the years into one of the wor~d's most famous mining fields in the form of a simple story.

Jan 1, 1940