Search Documents

By W J. Rankin, D R. Swinbourne

There are large tonnages of low-grade manganese ores in India fromwhich it is uneconomic to produce ferroalloys by conventionalsubmerged arc furnace smelting. A possible way to utilise these ores is to smelt them with carbon to produce pig iron and a manganese-rich slag, then to metallothermically reduce the molten slag to silicomanganese. Thermodynamic modelling of the metallothermic reduction stage using aluminium, silicon or aluminium-silicon alloy as the reductant at 1450¦C showed that an acceptable grade of silicomanganese could be produced. Manganese recoveries were predicted to be about 80 per cent. Heat balances indicated that silicothermic reduction may not produce enough heat to maintain reaction temperature. Small-scale laboratory experiments showed that the manganese grade of the alloys, and the manganese recoveries, were close to those predicted, but those for silicon were muchlower. Aluminothermic reduction produced the highest grade manganesealloy. The slag-metal equilibrium involving manganese, silicon and their oxides was investigated and it was found that equilibrium was not attained in any of the experiments, due probably to the very low rate of reactions involving silicon. This could be used to advantage in practice to achieve higher manganese levels in the alloys.

Jan 1, 1998

By J Masliyah, Z Xu

The largest oil sand deposit in the world is located in Alberta, Canada, with a total proven reserve of 2.5 trillion barrels of oil. The water based extraction process is currently being used in commercial operations to recover bitumen by flotation from oil sand ores. A recognised challenge in bitumen extraction is the reduced bitumen recovery when processing ores containing high fines content or æweatheredÆ oil sand ores, collectively known as poor processing ores. Inspired by demonstrated success of using kerosene as collectors in coal flotation, an innovative idea of using oily bubbles (air bubbles coated with a thin layer of oil or solvent) was tested to improve bitumen flotation recovery from poor processing ores. In this study, dynamic contact angle of air bubbles or oily bubbles on bitumen and induction time of bitumen-oily bubble attachment in water were measured to justify the use of oily bubbles in bitumen recovery from poor processing ores. The type of oil or solvents, including kerosene, toluene and naphtha, used in generating oily bubbles showed a marginal effect on the contact angle values, similar to the values measured with air bubbles. However, the spreading of an air bubble was found to be much slower than that of oily bubbles on a bitumen surface. The induction time for oily bubble-bitumen attachment was found to be much shorter than that for corresponding air bubble-bitumen attachment in the process water from poor processing ores. The reduced induction time for kerosene-coated air bubble-bitumen attachment correlates well with the improved bitumen recovery from poor processing ores using kerosene-coated oily bubble flotation technology.

Jan 1, 2005

By D Stacey, J Matthews

Hunter Valley Operations in partnership with Orica Explosives designed a process to optimise coal extraction at depths greater than 65 m below the Hunter River in a safe and cost effective manner. The process involved a team approach to investigate the relationship between geology, mining sequence, vibration and blasting methods adopted. From this an optimum method for uncovering the coal was developed.

Jan 1, 2001

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By Y Xie, L O’Connor, S C. Dominy

"Sheeted vein gold deposits are characterised by multiple subparallel veins and free milling gold. In situ heterogeneity of mineralisation results in grade and process parameter variability, which will increase project risk. Measured variability is often enhanced by poorly designed sampling and test work protocols. Protocols that are optimised within the framework of the theory of sampling to suit the ore type, together with quality assurance/quality control systems, will reduce variability and provide fit-for-purpose results. The geometallurgical approach requires spatially distributed samples within a deposit to support variability modelling. Diverse attributes from core logging, mineralogical/textural determination and small-scale tests are used to measure variability. This contribution emphasises early stage geometallurgical intervention during project development. It presents a discussion of representative sampling in the context of the theory of sampling. A case study presents a protocol that exemplifies how data can be gained from a well-designed and planned program to support a resource estimate and prefeasibility study.CITATION:Dominy, S C, O’Connor, L and Xie, Y, 2016. Sampling and Test Work Protocol Development for Geometallurgical Characterisation of a Sheeted Vein Gold Deposit, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 97–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By G R. Hancock, M J. Saynor, J B. C Lowry, K G. Evans, M Narayan

Tools such as landform evolution models (LEMs) provide a means of predicting how a landform may evolve over extended periods of time. Here, we utilise the CAESAR-Lisflood LEM to assess a proposed rehabilitated landform of the Ranger Uranium Mine in the Northern Territory of Australia (Figure 1). The environmental requirements for the closure of the mine state that the final landform must be able to physically isolate tailings material from the environment for a period of at least 10,000 years (Australian Government, 1999). However, uncertainty exists as to the reliability of model predictions representing thousands of years.In this study, we use model predictions from an undisturbed pre-mine landform to calibrate the parameters used in model simulations of a post-mining rehabilitated landform over a simulated period of 1,000 years. Specifically, we vary environmental conditions such as rainfall, presence/absence of vegetation and surface particle size characteristics in a series of model simulations to determine their impact on the respective landforms, to revise model input parameters as required. A simulated period of 1,000 years was used as it represents a period in which long term landform evolution patterns and trends may be established and identified. CITATION:Lowry, J B C, Narayan, M, Evans, K G, Saynor, M J and Hancock, G R, 2018. Using an undisturbed landform to calibrate long-term predictions of the evolution of a rehabilitated landform, in Proceedings Life-of-Mine 2018, pp 133–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

Australia as a leading producer of mineral sands has also occupied a leading position in many areas of research'in the processing and applications of these minerals. Research in upgrading ilmenite to produce synthetic rutile has resulted in the develop- ment of many processes, e.g,., Becher, Murso, Chlorine Technology, and ICI processes. Studies on the reducibility of ilmenites, aqueous leaching of reduced ilmenites, Fe-Ti-O system, leachability of natural and treated ilmenites in hydrochloric acid and selective chlorination of iron from ilmenites have been carried out in order to develop and improve the efficiency of the above processes. While research on the processing of zircon sand to produce high purity (99.99% ZrO2 zirconia powder and zirconium chemicals started only recently, research by CSIRO in the early 1970s led to the discovery of the phenomenon of transformation toughening in partially stabilized zirconia (PSZ) ceramics. Australia, with very significant resources of lanthanide-containing ores, pro- duces substantial quantities of monazite each year but research in processing and appli- cations of rare earths was neglected in recent years in this country. However, research to improve processes for the recovery of rare earths is now under way and studies on the production and testing of Nd-B-Fe magnets which are 1.5-2 times stronger than the strongest magnets (Sm-Co) currently available, have also commenced.' An overview of the research in the pro- cessing and applications of mineral sands during the last two decades in Australia and its implications for the industry are pre- sented in the paper.

Jan 1, 1986

By W J. Cowie

Several years of operating experience of over 100 gold recovery operations on the West Coast has provided a database from which the basic operating costs of these types of operations can be characterised. Using figures generated from the averaging of plant operating costs throughout the region and financial modelling using Lotus spreadsheets has been developed to analyse both existing and proposed developments. This type of modelling has several uses: 1. Identification of the impact on profitability of changes in management practices, finance costs, operating costs and revenue streams. 2. Project evaluation and planning. 3. Profitability projections for development financing. 4. Troubleshooting with existing operations. 5. Valuation of existing operations and properties.

Jan 1, 1987

Technical disputes, commercial negotiations and workplace/societal conflict are a natural part of doing business and just living itself. Conflict is everywhere û at home (between family and neighbours); in the workplace (between management, co-workers and unions), with contractors and with other companies; and everywhere at the community level, dealing with land access (pastoralists/farmers and indigenous/First Nation people), environmental protestors and NIMBY-ites - Civil Society in general. Exploration and mining companies, operating in more remote, less developed and culturally diverse regions, tend to encounter myriad areas of conflict (typically emotion-charged) and they are outlined. Dispute prevention, management and various binding and non-binding resolution techniques are discussed. The paper gives a general overview of the ADR nomenclature and framework (mediation, conciliation, expert determination, adjudication, arbitration and litigation) encouraging technical professionals to participate. Its thesis is that lawyers should not necessarily be the first port of call when problems arise between the mining workforce, contractors, joint venture partners, purchasers of prospects/mines, traditional land owners, protest groups, etc. If the matter must be litigated, the role of the expert witness is critical in pretrial planning, negotiations, mediation and litigation management, so a few guidelines are provided. Whilst dispute resolution has a legal context, the paper is written from an AusIMM technical professionalÆs perspective, emphasising practical long-lasting pragmatic solutions.

Jan 1, 2006

This report will differ slightly from the traditional scientific and technical discussions given at this type of conference. It will focus on the personal experiences and choices that I undertook when deciding on my graduate position and location after completing university studies. Throughout the duration of my course I had experience in both fly-in, fly-out operations in the Pilbara and residential operations in the West Australian Goldfields. These experiences, though limited, allowed me to explore the two different methods and their pros and cons, and consequently to make my choice for graduate employment. Throughout the duration of my degree I believed it was important to gain a basic understanding of the two methods, focusing on lifestyle and personal interactions. The decision that a residential site suited my personality and lifestyle then allowed me to refine my job applications to a more specific list of mine sites and companies, resulting in a residential position with BHP Billiton at their Iron Ore operations in the Pilbara, Western Australia.

Jan 1, 2005

By E J. B van Etten

Pit lakes may form when open cut mining leaves a pit void that then fills with ground and surface waters. This often replaces terrestrial ecosystems that existed prior to mining with an aquatic ecosystem, affording an opportunity to improve regional aquatic biodiversity values through targeted aquatic restoration (McCullough and van Etten, 2011). Restoration theory provides guidance when restoring disturbed systems towards landscapes that are of regional value and relevance. But how do we identify a restoration target for a novel aquatic habitat that only exists in the new post-mining landscape? This paper presents a process of first identifying and then surveying local representative aquatic systems, to provide a direction for pit lake restoration efforts and achievement criteria for pit lake relinquishment, using a case study from a sand mining operation amongst wetlands in south-western Australia.The company mines silica sands following mechanical removal of topsoil and then extraction of the ore from below the watertable by dredging. Assessment of wetland and riparian vegetation was achieved through the establishment and measurement of temporary monitoring transects across five natural wetlands in the Kemerton area. Several more regional wetlands were also visited and observations made to supplement and validate these data.Distinct vegetation zonation was found across each wetland, although typically wetland basins were unvegetated or filled with younger woody plants with patchy distributions. Fringing riparian vegetation consisted of few species (commonly the paperbark Melaleuca rhaphiophylla and the sedge Lepidosperma longitudinale), but community composition and structure were variable between wetlands. The pattern of vegetation seen across natural wetlands was best explained by topography and soil chemistry, with low lying wetland areas more likely to experience regular flooding and accumulate organic matter and nutrients.In conclusion, where they are available, regional natural waterbodies may constitute the best valid restoration goal. Nevertheless, the goal may need to consist of a range of closure design opportunities, rather than a single target.

Oct 5, 2011

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

By J Dyt, S Lyons

In the mining industry, crusher-related incidents have led to 15 reported deaths in Australia, New Zealand, and the USA between 1998 and 2007 (NSW Government Resources Regulator, 2024). The majority of these fatalities occurred during routine crusher maintenance tasks. A survey of quarry and mine site maintenance staff was completed to ascertain what they thought of such safety device to understand if beneficial and if so reasons if unused. Overall, findings show, staff perceived risks differently, cost, familiarity, device awareness and not front of mind, influenced adoption. This underscores the importance of asking the right questions involving maintenance and safety staff to lead to more proactive risk assessment.

Apr 16, 2024

By J Paradis, K Dudgeon, M Topping

At Newmont’s Jundee Operation, exploration and resource geologists collaborated to produce an open pit resource model. Using a variety of modelling and estimation techniques but no new data, an uneconomic underground target was converted into a potentially economic open pit evaluation. During an industry downturn, it is more important than ever to efficiently share expertise, ideas and resources to problem solve and produce meaningful project outcomes. The two departments brought together different methods and ideas, and the process showed that certain methods worked better than others in different situations, thus the appropriate method was applied to each part of the evaluation. The results were used to create new procedures and improved lithology modelling and resource model estimations. Adaptability of the geology departments and collaboration such as this are key to ongoing improvements and future mine life at Jundee.CITATION:Dudgeon, K, Paradis, J and Topping, M, 2014. Cook open pit model – the hurdles: how we leapt, lunged, stumbled and overcame them, in Proceedings Ninth International Mining Geology Conference 2014 , pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Bacteria can play a key role in the processing of 'difficult' ores. Bioleaching opens the way to potentially extract copper from vast amounts of otherwise hard to process refractory low-grade chalcopyrite. In my talk I will outline our research philosophy to develop bioleaching as a Precision Processing unit process step. In our view, Precision Processing is a sophisticated approach to mineral processing where the ultimate goal is to measure and characterise the ore body in-ground and in real time during mining, allowing the down-stream unit processes (bioleaching, in this case) to be continuously tailored and tuned via feedback and feed-forward controls to obtain the highest possible recoveries at the lowest possible cost and environmental impact. I will describe some of the work that we are undertaking to better understand the interfacial phenomena underlying the fundamental bioleaching process with the aim of coming to a Precision Processing approach. We use techniques such as interfacial electrochemistry (scanning electrochemical microscopy, SECM), AFM, zeta potential measurement, and synchrotron science to elucidate the parameters that drive bacterial selectivity and adhesion, bacterial metabolism, and dissolution and precipitation processes for model systems and real chalcopyrite ores. As examples of our research, I will discuss in some detail our method to produce and characterise micro-patterned CuxS - silica thin films as model substrates for electrochemical and bacterial adhesion work and our approach to the interfacial chemical characterisation of extracellular polymeric substances of bio-active bacterial cells. I will also cover some of our recent findings relating to measurement and interpretation of bacterial adhesion on sulfidic substrates and its implications for bacterial adhesion and substrate selectivity. After having identified and discussed crucial leaching parameters, such as pH, Eh, T, [Cu2+], and [O2], the talk will go on addressing some of the early achievements and challenges encountered in our work to design and prepare low-cost, rugged sensing devices that allow the in-situ (in this case, in-dump or in-heap) localised measurement of these parameters. I will conclude my talk by painting the picture of how the work of our group might contribute to realising the dream of transforming bioleaching into genuine high-tech Precision Processing of minerals. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

Minerals Industry - 5 Year Outlook AusIMM sponsored project Positioning the Minerals industry for the 21st Century Does this seem right for New Zealand?  To ascertain the industry's perceptions of issues and capacity to address them: Industry context and issues Capabilities of professional staff Access to professional staff Balancing supply and demand Industry must do it. Cannot wait for others.   Some observations... Negative image - constrains capacity to influence community and government Major repositioning of professional staff competencies required Existing organisational arrangements and capabilities are under pressure to change Difficult to access professional staff of required capability Facing significant external challenges - with real concern about capacity to address them Prevailing culture not suited to needs of the future High level felt need for change The industry has a choiceà We can define where we want to be and act decisively Or We can respond to the future as it unfolds.

Jan 1, 2000

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014