Search Documents

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904

By Richard Divine

IN the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and, some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. To do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the. top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000°C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seen-is to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues.

Jan 8, 1914

By Lynn Howell

IN a previous articles we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon Which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in 'the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.' Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added. inside the chamber, This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously, Briefly described, the chamber moving in the hole is made of 3,2-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft, long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber, Above this is the vacuum-tube amplifier with its batteries and transformer, In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube, Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1939

J. M. HARTMAN, Philadelphia, Pa.: Mr. Fackenthal can remember some queer things that occurred at Durham, Pa., Aug. 3, 1876, while he was superintendent. The furnace was working stiff, i.e., blast-pressure 10 to 11 pounds, which was high pressure for those days. With this pressure there was some circulation through the stock. At 9 p.m., flushed cinder. After flushing, air was thrown off' for a moment to " bot up "; the keeper turned the lever and threw on air just as the scaffold dropped, which eased up the pressure to 4¼ pounds. The air-receiver is twice as large at Durham as at other places. The air from this receiver, added to the two seven-foot blowers, gave an extra large volume, which, rushing into the furnace, fired the finely-divided carbon, causing an explosion that threw part of the stock in the furnace out into the open air, threw up the bell-and-hopper with the tunnel-head plates, and gave off' a large volume of carbondust. The bell-and-hopper going up first, the stock followed, and, striking the bell-and-hopper, was deflected in a shower over the cast-house roof, breaking the slates. Sitting at the corner of the engine-house at the time, the stock pelted me, when I ran around the corner to get rid of it. Remembering there were two men at the furnace-top, I shut down the engines, and, running to the top, found them sitting in the hoist-house enjoying the fire-works. The explanation of this explosion is simple. There is in the blast-furnace a bed of fuel extending up, say, 16 to 18 feet above the tuyeres; in this bed of fuel some stray pieces of limestone are found, and a few pieces of unreduced ore; but, generally speaking, it is all fuel. On this bed of fuel is the zone of fusion. In this zone the descending stock is liquefied, except the fuel; the iron, melting, drops out of the ore, and the gangue unites with lime, forming cinder. The iron falls in the form of shot, and, with the cinder, trickles

Jan 1, 1899

By Benjamin Talbot

The problem of segregation and cavities in steel ingots is a subject which has given and is still giving metallurgists, engineers, and operators matter for serious consideration. This question has come more into prominence lately in the United States, due largely to the desire of railroad engineers to secure a better rail than they have obtained ill the past, as the service they demand is increasing in severity; and no doubt manufacturers will be able to meet what is required of them. The rails here are as good as those made in other countries, but the conditions of service and the extremes of climate are more Revere and consequently more breakages occur. Various reasons have been advanced to explain why rails may not be as good in quality to-day as in the past. Some engineers consider that modern methods of manufacturing, designed chiefly to obtain large output, tend to reduce the standard of excellence of more deliberate methods. Others think that 4-ton ingots are worse than those of 2 tons. Again, it is stated that the 100-ton heat in one ladle is too large, and is a step in the wrong direction in casting. My experience upon the question of the size of the ingot is that in rolling rails of from 85-to 100-lb. sections, the range of ingot is only practically such that the difference in the size does not help in the question of segregation, cavities, or blow-holes. I call attention to two ingots from work done at Pencoyd, Pa., 16 years ago. These ingots were bottom-poured, cast at the same time from the same center-runner, the one being 20 by 24 in. and the other 13 by 16 in. in size. The steel was acid open-hearth, and contained C, 0.43; P, 0.062; S, 0.069 per cent. At the same place in each ingot where seg-

Jan 1, 1914

James Douglas will long be remembered as a distinguished mining engineer and metallurgist, as a scientist with broad vision, as an executive whose understanding of practical problems coupled with his knowledge of men and affairs enabled him to weld together great mining interests and to their service build railroads and bring power. More, he will be recalled as a philosopher and a writer of charm, a historian of no mean order, and one whose catholic tastes and enthusiasms led him into the fields of education, medicine and theology. His aim was to possess that which he considered made life worth while—friends and effectiveness in whatever task he undertook. In this aim he was successful to a degree exceeded by few, as thousands of his friends and associates could and can testify. Dr. Douglas was born on November 4,1837, at Quebec, Canada. His father, James Douglas, Sr., was a prominent physician and the leading surgeon of Canada. He also established the first retreat for the insane in the Dominion, the Quebec Lunatic Asylum, to which he devoted his services for years; The son followed in the footsteps of his father and studied medicine, not only in Canada but also in Scotland and in Germany. He entered the University of Edinburgh in 1855 but after two years at that institution returned to Canada and was graduated from Queens university at Kingston, Ontario, .with the degree of Bachelor of Arts. Later he went to Lava1 University, Quebec, and subsequently became professor of chemistry at Morrin College, Quebec. After he was graduated—at the time he considered his formal education completed—he traveled with his father in Europe and in the Orient; visiting Egypt, being especially interested in that country, several times. They gathered together an important archaeological collection which later was donated by them to the Metropolitan Museum of Art in the city of New York. James Douglas was also greatly interested in photography, a hobby in which he made use of his chemical knowledge. The writer can remember distinctly the descriptions he gave more than forty years ago in Arizona of the difficulties he encountered with the old wet photographic plates, especially while traveling in Egypt, when he prepared and used his own chemicals. In his humorous manner he told how he once discovered, in the nick of time, the nurse preparing to give the baby in the party a rub-down, using for that purpose the white, limpid

Jan 1, 1934

By Thomas W. Dawson

THE H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnage and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center, to center of pulleys. It operated at a speed of 250 ft. per min. and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons were carried by the belt. While this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on, the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and,, therefore, had to be crossed at each location to deliver coal to the river.

Jan 6, 1925

By B. C. Allen

Grain boundary grooving has been studied in chromium, molybdenum, and tungsten under a variety of conditions using high vacuum techniques and tantalum -gettered argon. The average surface free energy of solid chromium, and the chromium-liquid silver interface free energy were respectively found to be 2200 ± 250 and 500 i 130 ergs per sq cm from groove formation kinetics and estimates of pertinent volume difffusion coefficients. The results for chromium were unffected by variations in interstitial content ranging from 0.003 to 0.09 pct C, or 0.003 to 0.03 pct O. Surface diffusion is the primary mechanism of groove formation in chromium under 1 atm argon at 1200" to 140O°C, and is essentially unaffected by 0.003 to 0.09 pct C, 0.003 to 0.03 pct O , metastable nitrogen contents up to -0.01 pct, and up to 2 torr Ag vapor. At higher temperatures, the major mechanism is volume diffusion in argon or evaporation-condensation in stutic vacuum. Surface diffusion occurs in molybdenum at 0.5 to 0.96 and in tungsten at 0.5 to 0.9 of the absolute melting tempera -ture by a single mechanism, possibly by the migration of single adatoms or vacancies. Results were slightly affected by up to 23 tory Sn vapor, and in molybdenum were essentially unaffected by 0.5 Ti or carbon in the range 0.002 to 0.02 pct. Volume difffusion through the liquid is the mechanism of groove formation in chromium-liquid silver at 1200" to 1400°C and in molybdenum-, Mo-0.5Ti-, and tungsten-liquid tin at 1200" to 2000°C. The solid-liquid interface free energies involved were estimated from grooving kanetics. WHEN a grain boundary intersects a solid surface, a groove tends to form along the line of intersection at temperatures above about half the absolute melting point (0.5 TM). The groove progressively grows by preferential atomic migration either by diffusion or evaporation. Establishment of a groove angle occurs in accordance with the grain boundary and surface free energies involved. The motivation for groove formation is a reduction in the total surface free energy of the system. This study is a continuation of previous work on thermal grooving of chromium, molybdenum, and tungsten.&apos; The temperature ranges were extended, and the effect of metallic and interstitial impurities was evaluated. The results were such that certain interface free energies and surface self-diffusion coefficients were deduced from the grooving kinetics. EXPERIMENTAL WORK Materials and Preparation. As indicated in Table I, the 0.05-0.08-cm-thick chromium, molybdenum, and tungsten sheet used was nominally 99.99 pct after recrystallization. Two lots of molybdenum with about the same analysis, Mo-0.5Ti,* and tungsten were ob- *Alloy compsitions are expressed in weight percent . tained commercially. Extruded chromium rod,&apos; prepared from iodide process crystals, was warm rolled to sheet at 700°C. Sheet of three Cr-0 impurity alloys containing up to 0.03 pct 0 was prepared by warm rolling arc melted, extruded, and swaged rod. Two Cr-C impurity alloys containing up to 0.09 pct C were made by equilibrating unalloyed chromium with a known amount of CH4 for 24 hr at 1150°C in previously evacuated quartz capsules. Chromium containing nominally 0.015 and 0.06 pct N was similarly prepared by equilibration with NH3. The sheet was recrystallized to give a stable grain size about equal to the sheet thickness. Molybdenum and Mo-O.5Ti were recrystallized in a tantalum resistance furnace 1 hr at 1 x lo-5 torr at 2300" and 220O°C, respectively. Tungsten was similarly annealed for 1 hr at 2500°C. Chromium and its impurity alloys were outgassed at 1100°C and recrystallized 1 hr at 1700°C under 1 atm Ar. Except for nitrogen, the impurity content stayed roughly constant. Nitrogen in both alloys was reduced to <0.001 pct. In fact, over 80 pct of the added nitrogen was lost after outgassing at llOO°C and annealing sheet 1 hr at 1300°C in argon in the presence of tantalum. Such a rapid loss can be rationalized since -2 torr N are required for equilibrium with 0.04 pct N in solution,3 while the equilibrium pressure is ~10-5 torr over tantalum at 1300°C.4 The recrystallized sheet was cut into small coupons which were metallographically ground and polished on one side with a minimum of grain boundary relief. The surface roughness was on the order of 0.01 µ. The tin and silver used were nominally 99.999 spec-trographically pure. After being outgassed at 1100°C and equilibrated in a molybdenum crucible for 0.5 hr at 1800°C in argon, the tin contained 3 ppm 0, <0.3 ppm N, and 0.1 ppm H. Following outgassing at 900°C and equilibration in a chromium crucible 1 hr at 1400°C in argon, the gas content of the silver was 1 ppm O, <0.5 ppm N, and 0.3 ppm H. Grooving Under Argon or Vacuum. All specimens were placed in unsealed containers made from rod or sheet of the same alloy, thereby enabling the polished surface to achieve gas-solid equilibrium. The annealing fixtures are shown in Fig. 1. The specimen was placed in a resistance furnace with a tantalum or Ta-10W heating element plus tantalum fixtures or radiation shields. Chromium was outgassed at 1100°C, and molybdenum and tungsten were outgassed at 1900°C to 1 x l0-5 torr or at the grooving temperature, whichever was lower. In vacuum anneals, the specimen was then heated directly to the intended grooving temperature. In argon anneals, 99.996 Ar was admitted

Jan 1, 1970

By Gary Beerkircher

The mine hoisting equipment that is selected and installed at a mine is the lifeline of the mine, and therefore the proper selection of equipment will save a lot of time and money during the life of the mine. Various types of mine hoist designs &e available today, and each has their advantages and disadvantages. Double Drum Hoists, Single Drum Hoists, Friction Hoists and various special designs of these are available but should only be used on applications where they are suitable. There have been several new drive systems for mine hoists which have come into the picture in the last ten years, and they in turn must be evaluated along with the existing drive systems for each hoist application. It does not make sense to properly select the hoist mechanicals, and then have a drive system that turns out to be a bottleneck. This paper will attempt to cover the above noted systems - both the hoist selection and hoist drive system that will provide the mine with a reliable and economical hoisting system. I. Mine Hoist Types There are two basic types of mine hoists available in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Following is a general outline of each type of hoist and the hoisting applications that they are suitable for. First let us consider the simple Single Drum Hoist. As a Service or Production Hoist with cage or skip in balance with a counterweight, a Single Drum Hoist can efficiently service one or more levels since the location of the counterweight at anytime is not important. As a Production Hoist with skips in balance the Single Drum Hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the Single Drum Hoist. This has to be done periodically to compensate for rope stretch. A variation of the Single Drum Hoist is the divided drum hoist. If multi-layer winding is necessary the Single Drum Hoist must have a divider to allow a separate compartment for each rope. If a counterweight is used with a divided drum application the counterweight rope can be wound on a smaller diameter (Figure 2). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are reduced.

Jan 1, 1975

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 768 C (1414 F), the metal becomes nonmagnetic, and at the "A, point," 910 C (1670 F), it undergoes a change in crystalline form to become gamma iron. In the range 768 to 910 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1400 C (2552 E), it changes into delta (d) iron, which is identical with beta or non- magnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1537 C (2800 F); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A, point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always true. For example, the specific heat reaches a sharp maximum at the A2 point although no trans- formation occurs. (See Fig 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an ap-

Jan 1, 1951

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

By Richard W. Markley

A centralized online data acquisition system has been developed by the U.S. Bureau of Mines Pittsburgh Mining and Safety Research Center for rapidly digitizing, storing, and processing experimental signals originating up to 1100 feet away from a central computer. This system, which services seven laboratories, is currently based on a CDC System 17 1/- computer with 56K of semiconductor memory, four disk drives (one shared online with a CDC 1700), two magnetic tape drives, high-speed A/D hardware, and other input/output peripherals. The laboratories are linked to the central computer by 15-pair cables and signal conditioners and to the computer&apos;s communications controller by modems and current loops. The A/D throughput rate is approximately 30,000 samples per second (9 bit plus sign resolution) and permits scanning about 30 instruments once every millisecond for up to 100 seconds, being limited only by disk capacity. The laboratories serviced by this facility conduct explosions research and include such facilities as an Experimental Coal Mine Explosion Facility (45 channels), a Constant Volume Combustion Laboratory (4 channels), and a Simulated Coal Mine Laboratory (15 channels). Personnel support includes one systems analyst, two applications analysts, one operator, and a hardware technician. The system has performed adequately for burst-type data acquisition, but due to a lack of long-term reliability (24 hours) of the real-time multiprogramming operating system and unpredictable power failures, slow phenomena signals are generally digitized and stored offline. This latter data is input to the computer through peripherals such as a high-speed paper tape reader, or high-speed asynchronous communications ports. Processing of data is done either in real-time (as soon as data is collected) or in batch mode. Smaller batch jobs are run on this computer, and all others are transmitted by means of the system&apos;s high-speed UT 200 terminal simulator to a CDC-6000 series computer.

Jan 1, 1977

By AIME AIME

BOB VAN PELTS boyhood days in the mining atmosphere of Colorado apparently influenced him to direct hip college education first towards geology, at. Cornell College, then to mining at Michigan College of Mines and finally to graduate work in geology at the University of Chicago. He taught geology at his alma mater. Cornell College. served as geologist for the National Park Service then was on the staff of the Illinois Geological Surrey investigating and mapping mineral resources, and in 1928 because chief of the department of geology, mining, and metallurgy in the newly organized Rosenwald Industrial Museum (now the -Museum of Science and Industry,). He was made assistant director of the Museum in 1931.

Jan 1, 1941

Jan 1, 1907

By George C. Lipsey

FOR many years the mining of coal and other minerals occurring in sedimentary formation has been planned according to information obtained by diamond drilling. Placer mines have used churn drills for sampling and estimating deposits, and some metal mines have used the method either wholly or in part. The diamond drill method, therefore, although not entirely new, has come into more prominence in the last few years. Several large-scale developments now being planned or in the production stage have used this method in varying degree. This paper will describe the operations of the Howe Sound Exploration Co., Ltd. at Snow Lake, Manitoba, where a gold mine was developed and equipped for mining and milling wholly on the basis of diamond drilling results. The property has been in operation nearly 3 years, so that results can be compared with the estimates and assumptions made from the diamond drilling. In developing the subject it is necessary to outline as briefly as possible the normal method of mining, from discovery to production stage. Table I sets forth these various stages, the methods of financing, the percentage of total cost, and the relative time interval required for each section of the work. The plan presented in this table cannot be applied to all mining developments, but it gives a basis on which to work. In Stages 2 and 3 the investment is moderate, and if the property does not respond favorably the options or interests can be terminated. Stage 4 represents a sizeable investment, and it is more difficult to drop the property after this part of the operation is completed. Stages 2, 3, and 4 may be repeated several times by different groups or companies before Stage 5 is reached, but when Stage 5 has been started the total capital investment must be provided and there can be no turning back. It will be noted that there is a total of 116 units of investment in the overall cost if one company proceeds with Stages 2, 3, 4, and 5 in order. Stage 4, however, consumes time which is important when markets are being considered. Bringing a property into production when metal prices are low is much more difficult than when the prices are high, and if this stage can be set aside production is attained more quickly. When Stage 4 is eliminated the total becomes 86 units of cost for Stages 2, 3, and 5, but an adjustment of 14 units must be added to Stage 5. These 14 units represent the useable value of Stage 4. Thus Stage 4 represents an investment of 30 units if carried on before Stage 5, but 14 units if included with Stage 5. This is accounted for by the fact that development work can be accomplished more cheaply under Stage 5, since everything that is done is planned on a production basis with permanent services. Stage 4 must of necessity be governed by expenditures, and a great many temporary services, including housing and power plants, must be provided. The prospect shaft is a small one, and drifts,

Jan 1, 1952

By F. Julius Fohs

As an industry approaches stabilization, greater and greater stress must be laid on its technologic progress, which becomes a prime aid in improving its condition. The oil industry is tending toward this stage and hence its engineers must be pressed into greater service to prevent stabilization and stagnation from becoming synonymous, and to supply, either by improvements in processes or by new machinery, a means of obtaining savings in raw and finished products. Thus profits can be assured warranting continued investment. It may be repeated, technology must apply a slight improvement here, a change there, or a complete renovation, to eliminate inefficiencies and make each dollar invested yield greater results. The profits of ycstcrday were made of rich strikes, of monopolized patents or processes, of control of prices and of markets. Sixty-five years of growth, of large investment, of healthful competition, and of expanding markets, have put the oil industry in the foremost rank of world industries. .Just as the railroads passed a similar period of expansion and growth, and arc being stabilized with reasonable profits, so the oil industry must take advantage of the efforts of its engineers and experts to promote its healthful growth and a better service to the people. Herein is attempted a review of recent progress in which is presented the advances in exploration, production engineering, transportation, refining and greater efficiency in uses of petroleum, with a view not only to stressing important new processes and methods, but also the problems that press for solution. This review can only touch outstanding developments of recent years, but the several Petroleum Division symposiums of our program will present details worthy of attention. Exploration Geology offers directly little new in the technique of oil-finding— major stress being laid on improvement in subsurface correlation by means of foraminifera1 studies, additions to the knowledge of which are being made, slowly but surely, and by means of mineral, and especially heavy mineral, determinations in well samples. The general application

Jan 1, 1927

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941