Search Documents

By WALTER B. JONES

PIG iron was first produced in Alabama in 1818 from limonite or brown ore and since then much of this ore has come from the so-called mineral district of northern Alabama, especially along the Cretaceous-Paleozoic contact. For many years the Russellville district in Franklin County, where the first blast furnace was erected, produced more than 100,000 tons of brown ore annually. Limonite has been reported at many places in the Coastal Plain region, where the formations are of Mesozoic and Cenozoic age, but these scattered deposits were never considered to be of much commercial importance. However, in the last three years a considerable quantity of this ore has been scraped up and shipped, particularly from the city of Greenville in Butler County.

Jan 1, 1938

By Russell Webster

In having maintained production for more than 40 years Arizona's Magma mine is unique in a mineral district that includes several major copper mines. Other past and present producers in this area are Miami and Inspiration at Miami, the Old Dominion in Globe, the Ray mine in Ray, and to the south the new San Manuel mine near Tucson. Magma's production of copper, silver, gold, and some zinc has come from nearly parallel east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, about 1100 ft to the south. This vein system has been prospected and partially mined for some 9000 ft horizontally and 4800 ft vertically. In ascending order from the deepest exploration level, the Main vein cuts Pre-Cambrian schist, Pre-Cambrian Apache Group, Post-Devonian diabase, and Devonian, Mississippian, and Pennsylvania limestones. Until 1950 very little ore was obtained from replacement mineralization.

Jan 10, 1958

By Monte J. Pool, Rudolph Speiser, George R. St. Pierre, William T. Ebihara

Standard free energies of formation of WO,, W O W20058 and WO3from oxygen and the lower oxide or tungsten have been determined in the tempel-ature range of 700° to 1220°C. A tentative W-O phase diagmm is presented based on the evidence that the oxide phases, "W18O49" and "W20058", are unstable at l~atm total pressure, below 585° and 485°C:, respectively. A HE need for a complete quantitative treatment of the phase equilibria of the W-O system has been establishedby metallurgists during the past few years. In an attempt to improve the endurance of tungsten exposed to oxidizing atmospheres at high temperatures, many research groups have studied the kinetics of tungsten oxidation. The reverse process, the reduction of the tungsten oxides to metal, has also been investigated to some extent. Regardless of the particular interest, metal to oxide or oxide to metal, a knowledge of the phase equilibria of the W-O system is required to properly interpret all of the kinetic observations. It should be possible to state the stable phases of the W-O system at any given values of the chemical potential of oxygen and the temperature.

Jan 1, 1962

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1, 1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company's Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956

PHILIP D. BLOCK, JR., vice president of Inland Steel Co., visualizes a fine future for the Menominee Range of the Upper Peninsula of Michigan. He sees a future unclouded by threat from foreign ore imports or the development of low grade ore processing in Minnesota. The statement was made during the opening of Inland's new Cayia mine near Crystal Falls. Inland, according to the vice president, is planning to use an increased amount of the high phosphorous ores found on the Menominee Range. He said that other steel companies will probably do the same, because the steel industry has learned how to use ores of high phosphorous content. He said: "I do not mean to imply that we can use an unlimited amount of high phosphorous ores or that we can burden our blast, furnaces with 100 pct high phosphorous ores, but we have reached the point where we can absorb a much larger percentage of these ores without any detrimental effects. Foreign ores and lowgrade Minnesota ores cost too much to offer real competition, Block said. Transportation costs from the Menominee range to steel producing centers in Chicago and on Lake Erie are less than for any other range in this country. In the meantime, the American operators of the Bomi Hills iron ore mine in Liberia, have reportedly signed a new agreement with the Government. Several months ago, President Tubman of Liberia expressed a definite dissatisfaction with the original contract. Informants state that the agreement only needs the approval of the Export-Import Bank, which loaned Liberian Mining Co. $4 million to develop the iron ore properties. Majority stockholder of the Liberian Mining is Republic steel, with 61.57 pct of the stock. Under the new contract, the Liberian Government will start to share in the profits when the indebtedness is liquidated and the return of invested capital accomplished, or April 1, 1957, whichever is earlier. Under the old agreement the Liberian Government received a 5 cent per ton royalty and an additional sum based on the price of pig iron. The royalty rate reached more than 17 cents per ton this year. After debt liquidation the Liberian Government will receive 25 pct of net profits for the first five years; 35 pct for the next ten years; and 50 pct thereafter. Until the Government starts to share in profits it will receive a royalty of $1.50 per ton in U. S. currency, in addition to royalties provided for in the old agreement.

Jan 1, 1952

By F. Garofalo

It has been shown by various investigators that during constant stress creep the dependence of minimum creep rate, 6,, on stress, o, is given by em = A onat low stress levels, md by 6, = A' exp [ß s] at high stress levels. In these relations A, n, A', and ß are constant at constant temperature. A single relation has been found which satisfies conditions for both high and low stresses and agrees well with experimental results. This relation is 2, = AN (sinh a s)n, where A" is a constant at constunt temperature and a = p/n. This relation also satisfies the linear relation, 6, = k s, found at temperatures near the melting point at low stresses. EXPERIMENTAL creep results have led to a number of empirical relationships between minimum creep rate, 6,, and the applied stress, s. Under conditions of constant stress it is generally found that at low-stress levels,'-' the dependence of minimum creep rate is given by 6, = Asn. At high-stress levels'74 the experimental results fit the relation, 6, = A' exp [po l. In these relations A, n, A' and ß are constant at constant temperature. A model based on climb-of-edge dislocations from a pile-up array leads to a relation similar to that found experimentally at low stresses.' On the other hand. theories based on chemical-reaction rate,5 nonconservatively moving dislocation jogs, and jog migration and climb-of-edge dislocations4 lead to a relation similar to that found experimentally at high stresses. No difference in mechanism between low and high stress levels has been clearly defined; it is questionable whether such a difference really exists. In any event, the major argument usually given in substantiation of a change in mechanism from low to high stresses is that no single relation exists for defining the stress dependence of the creep rate over wide ranges in stress. However, such a relation has been found and is of the form, dm = A" (sinh a s)n, where A" is a constant at con- stant temperature and a = ß/n. This relation agrees well with experimental results over wide ranges in stress and temperature for copper, aluminum, an A1-3.1 pct Mg alloy, and an austenitic stainless steel. STRESS DEPENDENCE OF MINIMUM CREEP RATE At low stress levels the minimum creep rate, gm, depends on the stress, 0, under conditions of constant stress creep through the relation em=Aon [1] The quantities A and n have been defined previously. In the range in which this relation applies, a linear dependence is found in a log em,-log o plot. Above the stress range of application of relation [I], the minimum creep rate increases much mar; rapidly than predicted by relation [I]. This behavior is shown in Fig. 1 for a series of creep tests on copper4 at various temperatures ranging from 673 o to 973°K. Relation [I] is satisfied at the lower stresses, although the results at 973°K are quite limited. In all cases the transition beyond the applicable range of relation [I] is a gradual one indicating no abrupt change in mechanism. For all test temperatures, values of n have been determined from the results in Fig. 1. These are reported in Table I under Alog tm/hlog o. At high stress levels the stress dependence of minimum creep rate under conditions of constant stress is given by im = A' exp [ß a] 2] All factors have been defined previously. In a log em-0 plot, relation [2] predicts a linear function. Experimentally, a pronounced deviation from the prediction of relation [2] is found at lower stresses. As the stress is lowered, the minimum creep rate decreases more rapidly than predicted by relation [2]. This shown for copper in Fig. 2. Again it is found that the transition from high to low stresses is gradual and no really sharp change is found. Values of p determined from the high stress results are given in Table I. The dependence of minimum creep rate on stress at constant temperature for all ranges in stress

Jan 1, 1963

By A. O. Dady

PRODUCERS of both bituminous and anthracite coal have for many years been worrying about the gradually decreasing consumption of their product in the United States. Twenty years ago production had climbed to a peak of 569,000,000 tons of bituminous and around 90,000,000 tons of anthracite. In 1939 it was about 393,000,000 tons of bituminous and 51,000,000 tons of anthracite. This does not mean that the country is using less polver than it did twenty years ago, or that we are living in colder buildings. As a matter of fact, about three times as much electric power is now being consumed as in 1920. In general two factors are responsible for the drop in coal consumption: (1) greater efficiency in the use of coal, and (2) increased competition from hydro power, internal-combustion engines, and substitution of oil and gas for coal in conventional furnaces. As to the first factor, it took 3 Ib. of coal to generate a kilowatt-hour of electricity in central stations in 1920 and it takes 1.4 Ib. now; it took about 175 Ib. of coal in railroad locomotives to haul 1000 long tons a mile in 1920 where it talces about 120 lb. now: and marked economies have also been made in the use of coal in steel plants: in by-product coke ovens, and in other large uses. As to the second factor, three times as much electricity is produced from water power now as was produced in 1920; three times as much oil is being consumed in various ways; and likewise, the consumption of natural gas has tripled- whereas coal consumption in the same period has dropped by 40 per cent

Jan 1, 1941

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By I. A. Ettlinger

DEPRECIATION allowances have become firmly rooted in our income tax structure both by legislation and by court decisions. Secretary of the Treasury Morgenthau has recently stated before the Ways and Means Committee of the House: A taxpayer who did not provide for depreciation of assets used in his business could not long remain in business and the income tax should be levied on the assumption that he will provide for such depreciation. The 1934 Revenue Act has now been enacted, the depreciation provisions of the 1932 Revenue Act having been carried forward without change. However, there has arisen, in connection with the preparation of this new Revenue Act, a determination by the Treasury Department to make certain changes in the future administration of the depreciation allowances that will affect all corporations, and mining companies in particular.

Jan 1, 1934

Jan 1, 1962

Jan 1, 1925

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By J. E. Schiller, S. E. Khalafalla

To improve technology for treating process water, US Bureau of Mines research has shown that magnesium oxide (MgO) has many advantages over lime or caustic soda for precipitating heavy metals. Sludge produced by MgO occupies only 0.2-0.3 times as much volume as the precipitate made wing a soluble base. While a settled, lime-formed precipitate is easily resuspended, the MgO-metal hydroxide sludge becomes cemented together on standing. Settling of the metal hydroxides from a dilute suspension is more complete than precipitates formed with other bases. Virtually any metal that can be precipitated by raising the pH can be treated using MgO. A three fold to fourfold stoichiometric excess of solid reagent is added. The mixture is reacted for five to 10 minutes. Polymer is added, and settling or filtration completes the process. Because of the greater cost of MgO compared with lime, large-scale practice of this technology will probably be limited to water containing 50 mg/L (3 gr per gal) or less of dissolved metals. For such dilute solutions, chemicals are not a large fraction of total treatment costs, so more desirable sludge properties might justify higher chemical expenses. While the MgO process is technically suitable for widespread application, the extent to which it is adopted will probably be determined by a trade-off between the greater cost of MgO compared with lime and the superior properties of the precipitates and their corresponding ultimate disposal costs.

Jan 1, 1985

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates' have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By W. E. Rudolph, R. E. Baylor

DUE to its location in the Atacama Desert, one of the most barren of the earth's surfaces, Chuquicamata's water supply presents unusual problems. Yearly rain-fall averages less than one tenth of an inch at the plant. However, there are summer showers above 12,000 ft in the Cordillera to the east, the resulting run-off flowing through old river valleys buried beneath more recent volcanic formations, to be impounded within sediment-filled basins. This water emerges at springs where the outlets of these basins are blocked by lava flows, and here are formed the small streams which feed the only important river of the region, the Rio Loa. Chuquicamata's water is obtained from these springs and rivulets. [ ] The map above indicates four pipe lines from which potable and industrial water are supplied. Potable water, amounting to 4500 metric tons per day, is conveyed in the Toconce pipe line from springs 59 miles due east of Chuquicamata. This water is used not only for drinking, but also for boilers and other needs requiring high quality. For industrial water at the oxide plant, there are two 12-in. pipe lines from the Rio San Pedro, carrying a total of 17,000 metric tons per day of slightly brackish water. This water is at present used mainly for leaching and for hygienic purposes. Water Source Found For the present and future needs of the sulphide plant, it was calculated that at least 32,000 metric tons per day of make-up water would be required. For this purpose, a pipe line of 44 miles length was constructed to bring in the entire flow of the Arroyo Salado, one of the eastern tributaries of the Loa. The salt content of this water is so high (over 5000 parts per million of solubles, mostly chlorides) that it is highly detrimental to farming, and the Chilean Government had been studying projects to separate these waters from others of the Loa system in order to improve agricultural conditions in the fertile valley of Calama. So it happened that the Government was willing to award rights to the Arroyo Salado waters under agreement whereby the Mining Company removes waters from the Rio Loa system above Calama for all time. The outlet of these waters, after serving their purpose at the new concentrator and leaving the plant in tailing, is the Salar de Talabre, an old salt lake which presents fully ten square miles of surface to serve as an evaporating pan, the outlets having now been blocked by dams. Here the dry climate of Chuquicamata is a favourable factor, evaporation averaging slightly above 1/4 in. per day. The Toconce and San Pedro pipe lines have been functioning from 26 to 34 years, and through the use of special cleaning tools which were developed at the plant, as well as deaeration of the more active Toconce water, these pipes are now maintained at capacities which do not diminish as years go on. Constructing the Dam The Arroyo Salado pipe line design and construction involved certain special and interesting features, and inasmuch as this line and its intake works are solely for the needs of the new sulphide plant, more detailed description is given. The waters are impounded at a gravity dam constructed of concrete to a height of 100 ft above the river bed, keyed into the precipitous Dacite walls of the narrow canyon (barely 6-ft wide at the bottom, only 25-ft width at 50 ft above). A small secondary dam was built 100 ft down stream from the main dam, providing a pool of 15-ft depth to protect the main structure from flood flows over the spill-way during the rainy season. A system of four 36-in. syphons was designed for discharging these flood waters from the lower depths of the lake, in order to avoid eventual sedimentation behind the dam. The lake has a length of 3300 ft, and its water level is controlled by an adjustable spillway permitting draw-down of eighty inches, amounting to 41,000 metric tons of available capacity. This regulation is necessary because of wide fluctuations in stream flow between day and night due to freezing of feeders. During the construction of the dam the entire river flow was handled within a 36-in. pipe line some 2000 ft in length. As the excavations proceeded

Jan 1, 1952

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By W. J. Schuster

Safety in coal mines depends largely upon adequate training of the foreman. Although management must provide modern and safe equipment and at all times keep mines in first class condition from a safety viewpoint, final results will be determined by the quality of supervision. HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large underground mines in eastern Ohio. The section of Pittsburgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it. Haulage System The Pittsburgh No. 8 seam in eastern Ohio is relatively level, with only minor local dips. Throughout the Hanna Coal Co. mines, entries are generally 12 ft wide. Rooms are driven on a 60" angle on 30-ft centers and are 22 ft wide. No attempt is made to extract the 8-ft pillars between. The entire length of main line haulage is gunited in one mine, and a major portion in another. Two of the mines have single-track main haulage roads with passways. The third, a new mine, is double-tracked, and the roof is supported by steel crossbars, 60 lb or heavier, spaced on 4-ft centers and lagged. In recent years timbering on main line and secondary haulage roads has been accomplished by one of two methods: 1—crossbars are supported on a small section of post set in a hitch hole in the rib, or 2—or a hole is drilled in the rib about 12 in. below the roof, of sufficient depth to fasten securely a short length of 40-lb rail, the bottom of the rail facing the roof, on which a short post is set directly under the crossbar. At present the hitch-hole timbering method is favored. At two of the mines the main line haulage locomotives are 26-ton, 8-wheel units. These locomotives are of the axleless type, each wheel being individually mounted on the frame. The motorman's compartment is encircled by 3-in. armor plate for the protection of the occupants. At the third underground mine conventional 15-ton locomotives are being used. However, these locomotives have been completely rebuilt in the company's shops. Equipment has been streamlined and quarters have been provided for two people, who are protected by heavy steel plate in much the same way described above. This modernization program has been completed on all secondary haulage locomotives at the three mines, and the company is well on the way to similar equipment of the 6-ton section locomotives. The following additional features have been included in their modernization: 1—additional support for the motors to prevent their falling to the middle of the track and derailing the locomotives should a break occur in the suspension bar support; 2—installation of additional bracing to prevent brake rigging from becoming displaced and causing derailments; 3—enclosure of all electric wiring in conduit or raceway; 4—provision of an enclosed compartment for the storage of re-railers, jacks, and other equipment, so that they need not be carried on the outside of the motor; and 5—redesign of the end of the locomotive opposite the operator's compartment to prevent anyone's mounting from that direction. It is interesting to note that some

Jan 1, 1955

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.' The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By G. B. Misra

While investigating on the aerodynamic resistance of airways supported with peripheral timber sets, at regular intervals, the following theoretical equations were developed by the author to estimate the resistance coefficient of such airways: [ ] for S < 1, where f is Darcy-Weisbach resistance coefficient of the airway, C is modified drag coefficient of the supporting member, D is equivalent diameter of the bare airway, 8 is ratio of the approach velocity over the sets to the average velocity of the bare airway, A is cross-sectional area of the bare airway, a is projected frontal area of the sets, A., is cross-sectional area of the air stream at the vena contracta inside the set, S is spacing of the sets, f, is resistance coefficient of the bare airway, l is length of aerodynamic influence of sets, p is perimeter of the bare airway, p, is setted portion of the perimeter of the bare airway, pe is unsetted portion of the perimeter of the bare airway, and P shielding factor. The equations were verified experimentally in a model rectangular airway supported with one- (bars), three-, and four-piece sets of square-section timber of three different sizes and were found to hold true. The work has been further extended to one-, three-, and four-piece sets of round timber of 2.6, 3.2, and 3.8 cm diam with the same experimental set up. Tests have been carried out for spacings of 25, 50, 75, 100, 150, and 200 cm over a regime of flow defined by the Reynolds number (with respect to the equivalent diameter of the bare duct) ranging from about 1.5 X 106 to 5 X 106 using the same experimental techniques. The values of f are calculated in the manner indicated in [Ref. 1]. Unlike with square-section timber, the resistance coefficient f of the airway setted with round timber shows a distinct variation with the Reynolds number of flow. This conforms to observations made by Sales and Hinsley.2 In order to have a comparable value of f for all types of sets with all sizes of timber, it was necessary to select the value of f at a fixed Reynolds number of flow. Since f is chiefly a function of the drag coefficient of the sets, the appropriate Reynolds number RE is that with respect to the diameter of timber in the set. Considering the diameters of timber used and the regime of flow over which measurements were made, f was chosen at a value of RE = 20,000 in all cases. The f vs. S curves are maximal in nature and in conformity with theory, the f vs. 1/S curves are straight lines up to a value of S = 1 beyond which they show a distinct flexure. The observed values of 1, the length of aerodynamic influence of sets, agree with the relation 1 = 42 e, developed for square-section timber sets, thus suggesting that the shape of timber has little influence on the length of aerodynamic influence. The value of the modified drag coefficient CD for round timber was calculated in the same way as for square timber in Ref. 1, taking the contraction factor Z = 1.5 for round-edged constrictions. CD has an average value of 0.96 with a standard deviation of 6.08% as compared to the free stream drag coefficient of 1.2 at RE = 20,000 for long cylindrical obstructions The shielding factor [ ] is plotted against S/1 in [Fig. 1]. The curves are more or less independent of the size of timber, but are different for the different types of sets, possibly due to their different degree of symmetry. Values of f calculated by the author&apos;s [Eqs. 1 and 2], using experimental values of CD&apos; and [ ] and taking I = 42 e, are plotted in [Fig. 2] against experimentally measured values of f for different types of sets with different sizes of round timber. The values agree closely with a standard deviation of only 5%, thus establishing the veracity of the theoretical equations developed by the author for round timber as well. A comparison was made between the Xenofontowa4 equations (the only other reasonable relations available for the estimation of the resistance coefficient of supported airways) and the author&apos;s [Eqs. 1 and 2] by comparing in [Fig. 3] the values of the resistance coefficient f computed by the Xenofontowa relations with those experimentally measured by the author. In order to make

Jan 1, 1975