Search Documents

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By W. M. Johns

The geological mapping of Lincoln and Flathead Counties was a five-year project undertaken by the Montana Bureau of Mines and Geology. This paper, written by the Project Geologist of the survey, is primarily concerned with the stratigraphy of the Belt rocks encountered in mapping. Lincoln and Flathead Counties of northwestern Montana are underlain by sedimentary rocks of the Belt Series of Precambrian age. In only a very small part of the area, near Libby and Troy, have economic mineral deposits been worked with any success. Most of the area has been inadequately mapped as to geology. The region is crossed by the Great Northern Railway and served by the Pacific Power and Light Co.; officials of these two companies believed that with better geologic maps, prospecting might be stimulated and lead to the discovery of mineral resources that would contribute to new economic development within the area. A cooperative mapping agreement was proposed jointly by the two companies to the Montana Bureau of Mines and Geology in May 1958, and thus was born the Kootenai-Flathead five-year project. The dual objectives of this project are: 1) the possible location of mineral deposits of economic value, and 2) the ''stimulation of prospecting exploration" by others. This was to be achieved by geologic mapping of some 6800 sq miles and by establishing a field office in Kalispell where prospectors could come to have their rocks and minerals identified and receive geological advice on their problems. This writer has finished four field seasons as Project Geologist and thus became familiar with the Belt section in the Libby, Yaak River, Ural, Thompson Lakes, Pleasant Valley, and Stryker quadrangles (see Fig. 1). Progress on the project is given in annual reports issued by the Bureau.* This *Montana Bureau of Mines and Geology, Bulletins 12 (1959), 17 (1960), and 23 (1961). paper is concerned essentially with the stratigraphy of the Belt rocks so far encountered in mapping. PREVIOUS WORK IN THE AREA Willis28 made the first study of the stratigraphy and structure in the Lewis and Livingston Ranges of Glacier Park just east of the project area. In 1904, Daly made a study of the Belt rocks of the 49th parallel, using the names from bottom up, Creston, Kitchener, Moyie, and Gateway, for rocks ranging in age from that of Prichard to that of basal Missoula group. Walcott26 studied the Belt rocks exposed in the Mission Range (see Fig. 1) and other areas to the south of the area under discussion. Calkins and McDonald made a reconnaissance of northern Idaho and northwestern Montana in 1905. Calkins was the first to use Walcott's term 'Ravalli' as a group name for the strata equivalent to the Burke, Revett, and St. Regis formations (see Table I). Clapp worked on the Belt of western Montana (including Lincoln and Flathead Counties) throughout his lifetime. The Fentons9 studied the Belt of Glacier Park and

Jan 1, 1962

Discussion of a paper of S. S. Rummy and W. F. SCHWEDES, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2613 to 2635. K. A. PAULY, Schenectady, N. Y.-I have seen this installation and I wish all those interested in the question of electricity as a mine pumping agent could see it. It is not only a model for mine installation, but might well serve as a model for any electrically driven pumping plant. I think I am correct in saying that the pumps are the largest electrically operated centrifugal pumps in mine service in America. I talked with Mr. Rumsey in Duluth just before coming here, and he told me that the actual tests of the equipment as installed checked very closely with the shop tests; that the water delivered by the pumps was slightly in excess of the guarantee, something like 3 or 4 per cent., and that no troubles except of a very minor nature had been experienced with the installation from the start. One point which has been brought out by Mr. Rumsey, and by others who have looked into this question, is the marked saving which' can be made by the application of electricity to pumps, especially to the main sump pumps. The pumps are always located a long distance from the boiler plant and the losses in the steam mains are large. While many of the steam pumps are of a very high grade, yet the tests seemed to indicate that the steam consumption is extremely large. The reduction in operating cost of one small installation which I. have in mind pumping against a head of approximately 2,000 ft.-which by the way was a reciprocating pump-reduced the pumping cost to the neighborhood of one-fifth of the previous steam cost. . The high steam cost was probably due to leakage in the engine and the loss in transmission in the mine, the pumps being located almost half a, mile from the boiler plant.

Jan 4, 1915

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By L. S. Richardson, N. J. Grant

REACTIONS of oxygen and nitrogen at low pressures with titanium have recently been studied by a number of investigators.1-3 Gulbransen and Andrew' noted that the reaction with nitrogen followed the parabolic rate law whereas the reaction with oxygen deviated slightly from this law in the temperature range 300° to 800°C. In the work reported here, commercial titanium (75 A) was used as the test material. Cylinders 2.5 in. long and 0.25 in. in diameter were machined from heavier bar stock. The test pieces were given a metallographic finish, immersed for 30 min in cold concentrated HC1, washed in water, then acetone, and dried with lint-free cloth. Reaction rates were determined in a modified Sieverts type apparatus by measuring the decrease in gas pressure of the reacting gas contained in a constant volume. The amount of gas added could be measured in a calibrated gas burette to an accuracy of 0.01 mm. During the course of a run the temperature never varied by more than 10°C and then only for brief moments. After placing the specimen in the furnace, the system was first evacuated for 12 hr at room temperature, and then flushed with purified argon five times, adsorbed gases being discharged during this period from the glass system with a high frequency spark coil. The flushing and discharging were repeated at 400°C. This rather involved procedure was found necessary after a number of trial runs indicated extraneous effects traceable to the system. Reaction periods up to 2 hr were used, at initial gas pressures of 0.2 to 0.5 atm. Experimental Results Fig. 1 shows the decrease in oxygen pressure for tests at 0.5 atm at various temperatures as a function of the square root of the time. Deviations from linearity are minor and the parabolic rate law is obeyed. Fig. 2 shows the same plot for the nitrogen reaction. A definite deviation from linearity is noted; however, it is probable that the higher initial rates are caused by the presence of small amounts of oxygen contamination, the initial faster rate changing to the slower rate after about 5 to 10 min. Calculations of the rate constants were made on the basis of the latter portion of the curves. The parabolic rate law constants calculated from these curves are shown for oxygen and nitrogen in Fig. 3. In spite of some scatter the average curves are quite definite. Changes in gas pressure of the order of 20 pct did not result in a measurable change in the rate law constants. The activation energy for the oxygen reaction was calculated to be 47,400 cal per mol (above 700°C), which is not in agreement with the value quoted by Gulbransen and Andrew' for lower temperatures, their value being 26,000 cal below 600°C. The activation energy for the nitrogen reaction was calculated to be 45,400 cal per mol above about

Jan 1, 1955

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.'*' For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3'11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965

By J. A. Morgan, R. E. Lund, D. E. Warnes

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurqical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuric acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional Purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions. SEVERAL years ago, St. Joseph Lead Co. undertook a research program to develop procedures for winning values from a complex ore. The deposit was a massive sulfide ore body containing upwards of 65 pct pyrite. Gangue, composed principally of quartz, calcite, dolomite, and alumina, comprised only 10 to 20 pct of the mineralized zones. Zinc, lead, and copper values were variable, but averaged about 6.7 pct Zn, 2.6 pct Pb, and 0.4 pct Cu. Early in the exploratory test work, it was established that the intimate physical association of the minerals in the ore made beneficiation by conventional flotation procedures difficult. Accordingly, in addition to a comprehensive program to investigate physical methods of ore beneficiation, a research program was established to develop a direct metallurgical method for processing the ore. After surveying a number of potential methods for recovery of both metal and sulfur values, effort was concentrated on the development of a sulfate roasting process. It is the pilot-plant development of the sulfate roasting-solution purification—electrolyzing procedures which forms the subject of the present paper. PREPILOT PLANT INVESTIGATIONS From a thermodynamic viewpoint, it is feasible to sulfate selectively a host of metals, including Zn, Cu, Pb, Cd, Ni, and Co, in an iron sulfide ore without sulfating iron. Of course, a number of conditions such as roasting temperature and gas composition must be controlled. In addition, as first disclosed by Hybinette,' an alkali metal salt is frequently beneficial in promoting the sulfation reactions. The application of fluid bed roasting to the sulfate roasting of nonferrous metals was pioneered by Stephens of Battelle Memorial Institute.' Subsequently, Falconbridge Nickel Mines, Ltd. developed an unique process for selectively sulfating and recovering nickel, copper, and cobalt from their nickeliferous pyrrhotite, which recently has been described in an excellent paper by Thornhill.3 One of the unique features of the Falconbridge process is that the feed is introduced into the fluidized roasting furnace in a manner such that the feed slurry is broken up into droplets and the droplets lose their moisture before contacting the surface of the fluidized bed. The dried droplets do not tend to cake or fuse, but rather remain as discrete agglomerates of concentrate particles and roast without significant degradation. St. Joseph, aware that Battelle Memorial Institute had participated in the development of the Falconbridge process, obtained permission from Falcon-

Jan 1, 1962

By Arthur F. Taggart

Some years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).' The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface cnergy according to Gibbs' equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp. Adsorption According to the modified definition, adsorption means concentration at an interface between different phases in a heterogeneous system (thus far the definition runs as before), by the action of some mechanism, of which nothing is properly implied in the word, and concerning which the user of the word is probably in entire ignorance. Thus defined,

Jan 1, 1930

By AIME AIME

AWIDE variety of subjects was discussed at the Wednesday sessions on Non-metallic Minerals. W. M. Weigel as chairman, presided at the morning session, and W. M. Myers, vice-chairman, in the afternoon. In the morning session a paper by W. N. Logan on "Mineral Wool Resources of Indiana" was read by H. H. Hughes. Mr. Logan explained that as Indiana is the principal source of mineral wool, the paper might well he entitled "Mineral Wool Resources of the United States."

Jan 1, 1932

By Lloyd Emory

THE region known as. Guyana or Guiana stretches along the north coast of South America from the mouth of the Orinoco River in Venezuela to the mouth of the Amazon River in Brazil. Politically, it is divided into British, Dutch, and French Guiana, extend¬ ing into Venezuela on the north and into Brazil on the south. Because the area is within the sweep of the northeast trade winds and of approximately the same latitude, plant' and animal life are fairly uniform throughout. The geology is very similar as far as the northern coast is concerned. The drainage is taken care of by a number of large rivers that flow northward directly into the sea. The Courantyne River, which roughly divides the area into half, is the eastern boundary of British Guiana.1 The lower reaches of this river are also the center axis of an ancient bay that at one time indented the coast-line at this point. The old shore-line and, in fact, successive shore-lines can be traced from near the present coast-line in, the northwest district of British-Guiana, south-east and inland, crossing the Essequibo River near Dahli, the Demerara near Christianburg, the Berbice at the mouth of the Kuruduni River and the Courantyne at Vaka-Kuyaha Falls. The line then swings around to the northeast and again approaches the coast near St. Lau-rent in French Guiana. This article will be confined to British Guiana and largely to the valley of the Demerara River, but for geographic names .and topographic details it might, however, apply to Dutch Guiana as well. British Guiana, which comprises about 90,000 sq. mi. and is as large as England, Scotland, and Wales combined, may be divided into three belts, the alluvial belt or coastal plain, the foot-hill area (often spoken of as the sand clay belt), and the hinterland.

Jan 1, 1928

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

A special committee on the Classification of Surface Mining Methods was appointed by the A.I.M.E. Board of Directors on Nov. 17, 1939. The committee was headed by Gerald Sherman, and the members were Chester A. Fulton, C. F. Jackson, Earl E. Hunner and Arthur Notman. The following form of classification was reported to the Board by the Committee on May 16, 1940, as its unanimous recommendation. SURFACE MINING Dry Mining Bottom Benching Bank Mining < Top Benching Dry Mining Dry Mining Bottom Benching Hydraulic Mining Pit Mining Dredging Dry Mining Top Benching Wet Mining Top Benching River Bed Dredging Subaqueous Mining Lake Bed or Dredging Ocean Bed (Hand Mining Ground Sluicing Hydraulicking Dredging In most cases the terms used in the accompanying outline define themselves. Bank Mining is distinguished from Pit Mining by its situation. In Pit Mining the ore is taken from an operation below the level of the surrounding surface. In the secondary classification, Bottom Benching is an operation in which a bench is attacked from below, but the material mined might be hauled up out of the pit or moved out horizontally or downward.

Jan 1, 1940

A special committee on the Classification of Surface Mining Methods was appointed by the A.I.M.E. Board of Directors on Nov. 17, 1939. The committee was headed by Gerald Sherman, and the members were Chester A. Fulton, C. F. Jackson, Earl E. Hunner and Arthur Notman. The following form of classification was reported to the Board by the Committee on May 16, 1940, as its unanimous recommendation. SURFACE MINING Dry Mining Bottom Benching Bank Mining < Top Benching Dry Mining Dry Mining Bottom Benching Hydraulic Mining Pit Mining Dredging Dry Mining Top Benching Wet Mining Top Benching River Bed Dredging Subaqueous Mining Lake Bed or Dredging Ocean Bed (Hand Mining Ground Sluicing Hydraulicking Dredging In most cases the terms used in the accompanying outline define themselves. Bank Mining is distinguished from Pit Mining by its situation. In Pit Mining the ore is taken from an operation below the level of the surrounding surface. In the secondary classification, Bottom Benching is an operation in which a bench is attacked from below, but the material mined might be hauled up out of the pit or moved out horizontally or downward.

Jan 1, 1940

By George W. Powel

IN the nation&apos;s effort to raise its magnesium metal supply to meet the ever increasing demand, the Government is relying not only on standard established practice but has extended its support to developments not so well proved-at least, not commercially proved. Within the past few months considerable progress has been made, not only in the definite output of metal but in the exploitation of new processes, the successful adaptation of which should, in a reasonably short time, assure an adequate supply of magnesium. Recent months have also witnessed a reshuffling of the favored methods as well as of the likely raw materials, with the mineral dolomite gaining in interest over its richer but less abundant competitor, magnesite, while the lowly sea water appears to be losing ground to the higher magnesian brines of Michigan and western Texas. Every month sees a new alignment and there are signs that still newer methods or raw materials will be in use before the industry finally stabilizes itself.

Jan 1, 1942

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By William R. Webster

This is a subject which our Institute has made peculiarly its own. In the first volume of its Transactions the analysis of steel received attention, and every subsequent volume has borne witness to the acuteness and industry of our members in the investigation of this subject. The keynote mas struck, in this as in so many other lines of progress, by A. L. Holley, in his paper on " Tests of Steel," read at the Easton meeting of October, 1873 (Trans., ii., 116)—an essay which may rank as a classic by reason of .its elegant form, logical force, and clear prevision of all the bearings of its theme, Taken together with the brief report of the discussion which followed it (in which Dr. Drown emphasized the effects of heat-treatment and mechanical handling, and Dr. Sterry Hunt the importance of minute variations in chemical composition, and of possible isomeric and allotropic conditions), it constitutes, after the lapse of twenty-five years, an admirable and adequate introduction to the long list of technical papers which have succeeded it. Three years later came the epoch-making papers of Dr. C. B. Dudley on the relation between the chemical composition and physical properties of steel rails, which, with the voluminous discussion they evoked, constitute a special volume, published by the Institute, and full of useful suggestions. If Dr. Dudley could be induced to resume this investigation, he would doubtless be able to solve many points still uncertain or disputed. But I cannot undertake to review the history of this subject, as represented in our Transactions—still less to restate all the contributions to it which have been made in books or in papers before other technical societies, since the initiative was taken by the Institute. My more modest purpose is to indi-

Jan 1, 1899