Search Documents

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By AIME AIME

THAT neither the Reconstruction Finance Corp. nor its subsidiary, the Metals Reserve Corp., are in competition with private enterprise was stressed by Charles B. Henderson in an informal talk before the N. Y. Section, A.I.M.E., on Sept. 23. Among other things, the speaker stated that the R.F.C., since its establishment, had authorized loans of $12,000,000, of which over $8,775,000 has actually been distributed. Of this amount, over $6,600,000 has been repaid. None of this money was appropriated by Congress, the sole assistance from that body being the initial authorization of $500,000,000 capital stock.

Jan 1, 1941

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By H. L. Gilbert, C. T. Anderson, W. J. Kroll

In a previous paper,' the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.% When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8 in. in diameter. The supply of direct current of high amperage for producing the desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flcxible tubing of the movable electrodc, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decsed to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 19oo"C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica accortling to the reaction: SiO² + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1949

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By A. G. Gilbert

Paradoxical is the word. The coal industry, despite reach- ing a 22-year high in production (590 million tons), has been tagged as having its back to the wall vis-a-vis its valiant attempts to quench the nation's still unabated craving for coal. What must be even more reassuring to the industry, infected once with rumors of a uranium takeover, is a nation's almost insatiable appetite for electricity. Between 1967 and the summer of 1970, utility stockpiles were being gobbled up, diminishing to 79% of the January 1968 level.

Jan 1, 1971

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By Thomas T. Read

Jan 1, 1913

By Donald M. Liddell, G. C. RIDDELL

THE cosmic ray continues to engage the attention of the physicists, and according to Millikan and Compton, experiments of the past summer indicate that these rays must come from interstellar space, but not from the stars themselves. According to press reports of the International Congress of Physicists at Rome, the view was given there that these rays have an initiating potential of over 750,000.000 volts. In the field of spectrographic investigation great strides have been made. The U. S. Naval Research Laboratories (R. F. Mehl and G. E. Doan of Lehigh) have just finished a year's work with a "radium torch" or "shadowgraphic apparatus" in the field of the X-ray, that bids fair to displace the latter to a great extent. The torch is more powerful., easier to operate and cheaper. Penetration of 10 in. of steel has been accomplished, which. is much -beyond the- -scope-, of the X-ray..

Jan 1, 1932

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By C. E. LAWAL

WITH the object of adapting high-school vocational courses to the industrial needs of the community, a few high-school officials in West -Virginia working with the School of Mines of the State university decided to try an innovation this year. The purpose of this experiment was to teach coal mining in two high schools situated in mining communities. We thought that if a course in coal mining would be included in the list of optional courses offered in the high school, it might interest some of the boys, and if the course were properly taught it would undoubtedly be of inestimable value to those boys who later decided to take up mining work as their vocation. This coal-mining course was started last September in the Berwind and Gary high schools in West Virginia. The high-school officials in their conferences with' us decided that we should work up the outline of this course and they would assign the science teachers of the schools as instructors, with ,the understanding that we would help 'these instructors with this work. We consented to all this and submitted -an outline to the school officials which they are following this year.

Jan 1, 1929

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948