Search Documents

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

HEAT-RESISTANT alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:12 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to 1.o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage II) of one per cent in ten thousand hours as extrapolated from rates per hour or tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at 1800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,1 in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably dose, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By AIME AIME

A METALLURGICAL research building is to be erected for the Armour Research Foundation at the Illinois Institute of Technology. It will be located at the corner of Federal and 34th Sts., Chicago, and fully equipped will cost $250,000. It will provide the Middle West with the largest and most complete of facilities for the conduct of developmental and industrial research in this field. The new building will be constructed around an existing foundry and metallurgical research building which has become too small to carry on and service the many research projects contracted for by the Foundation, having to do with steel, alloys, and nonferrous metals. After two bays of the new unit have been completed, the old unit will be torn down and the new one completed.

Jan 1, 1942

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

By G. E. Johnson

The problem of efficient reclamation of zinc base die cast scrap became interesting early in 1930. Die Cast Metal, as referred to in this paper, is a zinc base alloy with various proportions of aluminum, copper, magnesium, antimony and tin. Many attempts were made to work out some means of reclaiming the discarded die cast metal for re-use as new die cast metal. Difficulties in such reclamation were attributable to contamination by lead and tin from solder, chromium and nickel from electroplated coatings, and iron from iron inserts. This paper relates the experiments that led to the development of a specialized muffle furnace for the treatment of zinc base die cast scrap for the production of zinc oxide and zinc, and describes the development of the muffle furnace and the equipment now used commercially for these purposes. The Eagle-Picher Co. acquired all patent rights' for these developments from the International Smelting and Refining Co. in connection with their purchase of the East Chicago Plant. Zinc Base Serap Situation About 1935, the die cast scrap situation became increasingly acute for scrap dealers. This scrap was accumulating from dismantling automobiles and household appliances which contained die cast parts. Efforts to find an outlet for this type of scrap were intensified. The International Smelting and Refining Co. began to study the possibilities of a commercial process for the recovery of values from die cast scrap. At that time most of the die cast metal reclaimed was melted down in small kettles of from one to five tons capacity, the iron inserts being removed by skimming. The dross was skimmed off and disposed of as a zinc dross. The drossed metal was cast into slabs and was given the trade name "die cast slabs.". Distribution of the products produced by melting die cast scrap in kettles is shown in Table 1. American Process Experiments A method considered for the production of zinc oxide from die cast scrap was an adaption of the standard American Process of zinc oxide manufacture. Thus some die cast scrap was mixed with oxidized zinc materials and charged to Wetherill grates. The zinc oxidized to zinc oxide but, while the aluminum and copper largely remained in the residue, the color of the zinc oxide produced was impaired by copper contamination. As the proportion of die cast scrap was increased, liquation took place; that is, the metal trickled through the charge then solidified in the openings of the grates. French Process Experiments Several hundred tons of die cast scrap were purchased for test purposes and converted into die cast slabs. These slabs were charged into a French Process (horizontal retort) zinc oxide furnace with some electrolytic zinc. A satisfactory grade of zinc oxide was not produced. Distillation in Belgian Retorts It was then decided that, rather than attempt to use scrap die cast metal or scrap zinc for the production of zinc oxide, it would be advisable to redistill the die cast slab metal in a Belgian retort furnace. The opportunity to do so was provided by the closing of the zinc smelter of the Illinois Zinc Co. at Peru, Ill. Arrangements were made for the operation of a Belgian retort furnace for such redistillation purposes. The results of this experiment are summarized in Table 2.

Jan 1, 1950

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By AIME AIME

THE first meeting" of the Iron and Steel Division was held Tuesday afternoon, Feb. 17, with nearly 100 men present and C. B. Murray as chairman. This was a round table discussion of iron ore beneficiation and of its relation to blast-furnace operations, and only one paper was presented, by Clyde E. Williams. Mr. Williams discussed the future of the Lake Superior district in its relation to the iron and steel industry. He stated that although estimates had shown that the total life of the present known iron ore reserves of the Lake Superior district was 20 to 30 years and that many believed that as a result of this depletion foreign ores would be brought to the Atlantic Seaboard, thus causing a displacement of the steel industry to the East, he believed that the Lake Superior district would continue to be the important producer of iron ore used in this country for decades beyond the predicted time before the exhaustion of the present known reserves. He described the three general types of ores that required concentration and pointed out the needs for research and the proper methods to be used in processes for the beneficiation of these low-grade materials. He discussed the effects of fine concentrates and the use of agglomerated ores in the blast furnace. This general summary led to interesting and valuable discussion on the various economic, ore-dressing, and blast-furnace problems in large-scale development of beneficiation. Perry Harrison described recent developments in sintering and the properties of iron ore sinter. T. B. Counselman and W. H. Coghill discussed the merits of classification of iron ore previous to tabling. Robert Faulkner and J. E. Little described the beneficiation plant of the Bethlehem Steel Corporation.

Jan 1, 1931

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

Jan 1, 1969

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By F. H. McDowell

The increasing interest in the subject of electrical separation warrants the addition to what has already been written of a few lines covering the practical workings of the Tilly Foster mill under the direction of Mr. E. S. Moffat, General Manager. Since my last paper was presented to the Institute, Mr. S. P. Tomkins, the superintendent, has had thrust upon him for solution several problems complicated by the introduction of new conditions. 1. The richer portion of the lean ore dump, and that nearest the railroad track, having been worked up in 1890, the handling of the balance, including a largely increased amount of rock, could only be accomplished at an increased cost. 2. The tailings had accumulated close about the mill to such an extent that arrangements had to be perfected to move them further away.

Jan 1, 1893

By N. J. Sather

The history of the Bunker Hill mine dates back to August 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d'Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co.

Jan 6, 1961

By H. B. Menardi

The history, geology, ore deposits and current mining operations of the Huitzuco district have been described by C. W. Vaupelll and the current mill operations by David Segura.2 This paper completes the story of Huitzuco with a description of the reduction of the flotation concentrates. The predominant ore mineral in the Huitzuco deposit is livingstonite, a rare, mercury-antimony sulphide (HgS.2Sb2S3). Other associated minerals include cinnabar, stibnite and elemental sulphur. The gangue is largely limestone and gypsum. Former operators mined a selected grade of ore, from which the mercury was recovered by an expensive, inefficient operation. A considerable tonnage of rejects and fills, carrying mercury and antimony, was left in the mine. In order to recover both mercury and antimony from these fills and also from newly developed ore, a combination method has been developed, by means of which the livingstonite is concentrated by flotation and the flotation concentrates subsequently reduced to metallic mercury and antimony. An essential part of the flotation treatment, as developed by Segura, is the use of copper sulphate as an activating agent. A typical analysis of concentrates now being produced at the property is as follows: Hg, 7.73 per cent; Sb, 26.40; Fe, 1.20; S, 29.68; CaO, 11.50; MgO, 7.25; SiOz, 1.63; A1203, 0.65. PRocess foR Treatment op Concentrates In the development of a process for treatment of these concentrates, three different methods were investigated: (1) roasting in a Dwight-Lloyd sintering machine with an excess of air; (2) separation of mercury and antimony by distillation in a reducing atmosphere; (3) a third method, which ultimately developed into the present process. The third method involved a slow calcination at a closely regulated temperature with a limited admission of air, which separated the mercury and antimony, the raeroury passing out of the kiln with the furnace gases and the antimony remaining in the calcine or "sinter."

Jan 1, 1944