Search Documents

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Luiza Esteves

Corrosion testing was performed in white liquor from a Brazilian Kraft mill. Specimens of duplex stainless steel (DSS) and lean duplex (LDSS) were exposed at 170 °C for 30 days to simulate conditions of the digester. Corrosion rates were determined from weight loss measurements. After this exposure, the corrosion products formed on the steel surface was characterized by using scanning electron microscope (SEM) equipped with EDS, X-Ray Diffraction (XRD), and X-ray photoelectron spectrometer (XPS). EBSD can be used to quantify of basis balance phases in DSS and LDSS. General corrosion rates for UNS S32304 LDSS were higher than the UNS 31803 DSS in industrial white liquor at 170 °C for 30 days. XPS and XRD analyses indicated that the film formed after the immersion test may be consisted by Fe and Cr oxides and sulphides.

Oct 30, 2017

By José Dimas Arruda

O conhecimento do campo de fluxo dentro do molde pode oferecer uma oportunidade de melhorar a limpidez interna do produto final. A técnica PIV foi empregada para avaliar a distribuição de velocidade longitudinal ao longo de uma ampla seção variando da válvula submersa até a face estreita de um molde de lingotamento de placas, bem como a distribuição de velocidade transversal correspondente. Estas informações podem ser utilizadas para avaliar o grau de turbulência interfacial.

Jul 30, 2018

By Hormando Leocadio Júnior

A otimização operacional no setor de desbaste da Linha de Tiras a Quente da Usiminas, Ipatinga, proporcionou redução do tempo de processamento dessa etapa, criando-se condições para aumento das temperaturas dos esboços na entrada do Trem Acabador (TA). Desse modo, para manutenção das temperaturas de acabamento dos laminados dentro da faixa de controle desejada, seriam necessárias menores velocidades de laminação no TA. Com a finalidade de garantir temperaturas desejadas na entrada do TA, que possibilitem adequadas velocidades, foi desenvolvido um sistema de controle de temperatura de esboço, que é acionado e desligado automaticamente na região inicial (topo), na extensão necessária do esboço. Esse sistema permitirá uma ampla exploração da nova condição de desbaste em menor tempo, com menor variabilidade da temperatura de entrada no TA, prevenindo ocorrências de estiramentos e de carepa, por temperatura alta nos topos e baixas nas bases dos laminados, maior uniformidade de propriedades mecânicas dos produtos, assim como aumento na capacidade produtiva.

Jul 30, 2018

By Emanuelle Garcia Reis

Este trabalho apresenta as mais avançadas tecnologias do equipamento de resfriamento acelerado e têmpera direta da linha de laminação de chapas grossas da Gerdau Ouro Branco. O laminador de chapas grossas possui um conjunto de técnicas de última geração para controle de forma (Bending, Shifting e Smart Crown) integrado ao modelo matemático que define o esquema de passes ótimo em função das propriedades mecânicas objetivadas no produto final. Isso permite obter chapas grossas de aços microligados em várias classes de resistência mecânica de 600 a 1.200MPa e de boa tenacidade a -60°C.

Oct 30, 2017

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By Breno Totti Maia

A aciaria 1 da Usiminas Ipatinga é composta por 03 convertedores BOF e uso de ventaneiras para promover a melhor mistura do banho. No intuito de garantir e melhorar a estabilidade operacional da etapa sopro na produção, foi iniciado uma séria de desenvolvimentos na lança de oxigênio através da aplicação da tecnologia Slagless® com objetivos de melhorar a formação de escória, evitar cascão de lança, evitar cascão no sistema OG (recuperação de gases) e aumentar a disponibilidade de lanças através do aumento de sua vida. Os resultados apresentados são extremamente favoráveis, pois após a implementação da tecnologia, todos os objetivos foram atingidos associado com uma vida extremamente elevada do bico de lança, agora chamado cartucho, garantindo estabilidade e conforto operacional para a equipe da aciaria 1 da Usiminas Ipatinga.

Aug 15, 2017

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By DIEGO RAFAEL MONTEIRO DINIZ

Os processos de recebimento, armazenamento e distribuição de combustíveis em grandes empresas mineradoras necessitam de um controle robusto e eficaz de todas as operações, uma vez que representam elevado custo por tonelada de minério produzida e expedida. Para tanto, a automatização dos processos que envolvem combustíveis é necessária, capaz de promover redução de custos, aumento de produtividade, confiabilidade e precisão nos dados e melhorias nas condições de trabalho na gestão e operação em combustíveis. Foi aplicada uma análise descritiva de um estudo de caso de um projeto de automação para esta finalidade implantado na empresa VALE S/A. Foi feita uma avaliação sistemática dos recursos, equipamentos e tecnologias necessárias a completa automação e integração dos processos que envolvem combustíveis e os ganhos alcançados após a implantação.

Oct 30, 2017

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Johne Jesus Mol Peixoto

Utilizando um modelo físico de um reator RH em escala 1:7,5, simulou-se o processo de injeção de material dessulfurante na câmara de vácuo, buscando evidenciar a influência da vazão de gás e da diferença de densidade entre as fases sobre o tempo de residência e sobre o tamanho das gotas de escória arrastadas pelo metal, parâmetros essenciais para uma estimativa da taxa de dessulfuração. O aumento na densidade do fluido similar ao aço resultou em considerável prolongamento no tempo de residência e diminuição do diâmetro médio das gotas de óleo arrastadas. Para a solução salina (NaCl) como fluido de circulação, observou-se que a redução da vazão de gás aumenta o tempo de residência das partículas de dessulfurante. Tais resultados sugerem que existe uma vazão ótima de gás para alcançar maior eficiência de dessulfuração no RH, isto é, maior tempo de residência do material dessulfurante e arraste de gotas de escória de menor diâmetro.

Oct 30, 2017

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Andrew Salach

Experimento laboratorial avalia desgaste em rodas e trilhos de PR’s. Chegou-se a conclusão de que rodas com elevada dureza economizam desgaste de rodas e de trilhos.

Aug 16, 2017

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Welington Bermudes Merelles

A ArcelorMittal Tubarão, unidade de produção integrada de aços Planos, faz parte do Grupo ArcelorMittal, maior produtora de aço do mundo. A empresa localizada na Região metropolitana de Vitória (ES), tem como principais produtos bobinas a quente e placas de aço. Como resposta ao cenário econômico do País, que atualmente se posiciona com baixa atividade econômica e em busca de manter a perenidade de seus negócios, lançou um Programa para identificar e eliminar “desperdícios”, baseado na metodologia Lean Thinking/ Manufacturing. Uma das iniciativas, apontadas como oportunidade de aumento de produtividade foi a etiquetagem das Placas de aço em substituição ao processo tradicional de Marcação e Pintura das placas. Esta mudança no processo de identificação de placas, proporciona maior produtividade na área de Condicionamento de Placas e a possibilidade de aumentar a produção com menos recursos e custo operacional.

Oct 30, 2017

By Frederico Ibrahim Horta

As estradas de mineração influenciam diretamente nos custos de operação de mina e manutenção de equipamentos. A equipe de planejamento de lavra em conjunto com a equipe de operação de mina buscando a melhoria de seus indicadores de custos e produtividade realizaram várias melhorias no perfil de transporte da Mina Oeste. Para realização deste trabalho foram mapeados e projetados novos trechos da mina que poderiam ser melhorados em termos de inclinação de rampa, subidas, descidas e curvas. A realização destas melhorias, em conjunto com correções de drenagem e forragem das pistas, possibilitou a alteração do limite de velocidade dos caminhões fora-de-estrada em alguns trajetos de 40 para 50 km/h. Como resultado destas alterações, obteve-se um ganho de 18% na produtividade da frota de transporte e uma redução de 13% nos custos de operação.

Oct 30, 2017

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018