Search Documents

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By BernardThierry

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts. This new type of model enables us to concurrently simulate the fragmentation of the rock, its movement and the associated seismic levels, all within a few minutes, which is a time compatible with a production cycle. Due to the complexity of the model, this article reveals the main principles and compares the results of simulations with on-site measurements in various sectors, i.e. quarries, mines and tunnels.

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By Carlos Campos Junior, Leonardo Soares Chaves, Raul Carretero Hoz, Renato Jacome Costa, Davi Bastos Martins de Oliveira

The Vale’s Serra Sul mine, also known as S11D project, is one of the world’s largest open pit iron ore mines, located in Brazil’s Amazon region. The mine produces around 90 Mt of high-quality iron ore annually. Its unique orebody enabled the S11D project to adopt a truckless mining system with In-Pit Crushing and Conveying (IPCCs) for ore exploitation and waste stripping. The IPCCs system requires crushing the waste, mainly composed by the jaspilite lithology, and is also conveyed to waste deposits several kilometers away from the mine. Due to Amazon’s environmental restrictions, the project was designed with preliminary geological knowledge, leading to the installation of primary crushers not designed for the hardest jaspilite, with uniaxial compressive strength (UCS) up to 500 MPa. This resulted in low waste crushing performance, affecting stripping ratio and threatening future production. A project was developed to improve the fragmentation of the jaspilite, allowing higher waste IPCC production, and reducing the risk to the production due to low performance of waste crushing and conveying. The first challenge was the independence of the geological and the geomechanical models, while only the geological model was considered in blast designs, the geomechanical model describes six waste groups of jaspilite classified according to their strength. A new geological model was then created to incorporate the geomechanical classification, allowing different blasting design according to the rock strength of the jaspilite. The blasting pattern on most compact jaspilite was reduced 27%, from 22m² to 16m² in 9 7/8” diameter holes, with a proposed theoretical reduction of 23% of the P80, from 326mm to 250mm. The second challenge was the implementation of the new design, as this pattern size and the high powder factor (2.9 kg/m3) were paradigms for such a large iron ore mine. The measured results have shown 25% reduction of the P80, the crushing rate was increased by 17% (230t/h), saving around $2.4 million annually in crushing and conveying system maintenance.

Jan 21, 2025

By K. Best, D. Conn

The US Army Corps of Engineers KY Lock Project in western Kentucky presented the blasters and vibration consultants with a set of unique challenges. The blasters on this project were faced with difficult geology and joint set orientation and sequencing of blasts opposite from what the explosive engineer/blasting specialist had recommended. Combining these issues with strict vibration and air overpressure specifications, blasting as close as 7 feet (2.1 meters) from a new lock wall, site topography that influenced the air overpressure, limitations on seismograph geophone placement that led to anomalies in seismograph recordings; surprising lessons were learned by everyone involved in the project and it is the authors’ goal to share this valuable information with everyone in the blasting industry.

Jan 1, 2024

By E. Líder, J. Pavez, J. Rivera

The application of new technologies, methodologies, and the use of new products in mining operations is a practice that is becoming more common in the industry every day, added to the new challenges and restrictions found in the operation. In the city of Tierra Amarilla, the interaction between mining operations and the community presents a constant challenge given the proximity to the community and the limitations that this presents. Explosive charge mass, in conventional blasting using traditional explosives (ANFOs, packaged explosives for example) limits the explosive charge lengths (they are reduced), impacting the explosive charge productivity. To improve the productivity of explosive charge and fragmentation, the use of low-density explosives was proposed, allowing the increase of the explosive charge length, trying to maintain the vibration levels within the established limits (2mm/s), preserving the fragmentation of the rock in the required sizes. The present study shows the results obtained from the application of low-density bulk emulsion for production blasting charges using upward and downward fan drillings. During this process, 18 blasting events were carried out, of which 8 were Up-hole loading (average density of 0.75 gr/cc) and 10 with Down-Hole loading (average density of 0.95 gr/cc). In summary, a total of 110,760 tons of ore have been broken, using low density emulsion, meeting the proposed objectives such as: 33% reduction of vibrations, 12% overbreak (within the theoretical design), P80 of 11in and 4.6% in fines.

Jan 1, 2024

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By Felix Degold, Mark Ganster

Achieving a customer optimized fragmentation by using robust data from new technologies e.g. GPS positions of boreholes, fragmentation analysis to calibrate the geology and fragmentation prediction models. The inclusion of the collected data into the blast’s design makes it possible to accomplish a desired particle size distribution.

Feb 1, 2020