Search Documents

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

Pyrite and Chalcocite have different crystal lattice, with different dissolution rate in the same ac-id solution, the dissolution rate of which is accelerated with increasing redox potential, they are leached simultaneously at high redox. In present work, some methods are adopted to inhibition the bioleaching of the pyrite by controlling the redox potential. Shake flask experiment shows that the dissolution of pyrite and chalcocite is slow as redox potential <700mV(Eh), but the dissolution in-creases exponentially as redox potential>800mV(Eh), they have good selectivity at redox potential between 700mV and 760mV(Eh).

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By P. Holtzhausen, L. Auret, B. Lindner, A. Haasbroek

"Spiral concentrators offer a cost effective way to separate valuable minerals from gangue by displacing lighter materials to the outside, and heavier materials to the inside of the spiral. The separation can be seen as visible concentrate bands and splitters are set at the bottom of the spiral to effectively split the ore into various densities. As there are typically many spirals in a concentrator plant, it becomes ineffective to continually adjust the splitter positions manually. Vermaak et al. (2008) proposed to use image recognition to detect the concentrate bands, thereafter, creating a model predicting the positions under certain input conditions. This model could then be used for optimisation and/or control of splitter position or band position. In contrast an online concentrate band detection system would provide real time concentrate band positions without losing accuracy due to model generalisation. These systems are usually expensive and time consuming to develop, due to a lot of centralised features required (image capturing, image processing and/or feedback to a controller). This study took advantage of the recently developed Raspberry Pi minicomputer to perform rapid prototyping of an online image processing sensor. The Raspberry Pi, and accompanying camera module, offers a portable Linux environment which can natively run the required image processing algorithms. Furthermore, extensive use of OpenCV was made to reduce development time, by relying on existing and proven algorithms to detect the concentrate bands. The Raspberry Pi also incorporates generic input/output ports which can be used in future work to provide the signal to a controller. In conclusion, the Raspberry Pi was successfully used to perform real time concentrate band position detection on a spiral concentrator. This solution is more general than an experimentally identified input-output model and may be used for control or optimisation studies in a wide array of spiral concentrators."

Jan 1, 2014

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By W. S. Eu

Thermal treatment of mineral ores can initiate thermal phase transformations which can affect either their activation or deactivation, subsequently influencing their ability to dissolve in a leaching reagent. The formation of rutile and hematite from ilmenite minerals, for example, has been suggested to occur through a series of reduction and segregation reactions. This process has been used in beneficiating low-grade weathered ilmenite ores to higher grade rutile. Despite decades of re-search, the mechanism of this process is not well understood, because dissolved intermediates are poorly crystalline and are difficult to quantify, with the exception of the final rutile products. Previous studies have shown that disrupted intermediate phases, by thermal treatment, are most susceptible to reagent attack and can often demonstrate ?activation? effects. In this study, synchrotron based X-ray diffraction method was used to investigate in-situ and in real-time the transformation of ilmenite minerals to rutile and hematite during calcination. The rate of formation and disappearance of specific Bragg peaks during the reaction and thermal decomposition of the mineral were used to derive an understanding of the solid-state reactions. The effects of the mineral transformation were validated by laboratory based batch calcination and leaching in sulphuric acid. The results suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By Azin Zangooi, Cesar Gomez, James Finch

Frother concentration is a variable which significantly affects the flotation performance by decreasing bubble size and helping froth stabilization. Variations in frother concentration, which mostly go unnoticed in industrial operations, may affect these functions. Some factors that can cause variations include the fact that frothers are normally dosed based on feed tonnage and not solution concentration, unstable frother delivery, incomplete dissolution for low solubility frothers, addition of frother-free wash water, remnant frother in recycle waters and frother partitioning to the froth. A colorimetric technique developed for determining frother concentration on site makes it possible to detect the occurrence of these problems and to establish their magnitude, allowing conditions to be adjusted to reduce frother concentration variations. By sampling and analysis, frother distribution throughout a circuit can be established, referred to as ‘frother distribution mapping’. Experiences at several concentrators processing sulphide ores are used to illustrate time restrictions for sample analysis, and to demonstrate temporal and spatial frother concentration changes as a consequence of variations in the grinding stage, recycled waters containing frother, and frother partitioning.

Jan 1, 2014

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By R. J. Batterham

The science and practice of mineral processing has been driven for many years by the same set of challenges that shape the mining industry ? demand and supply, grades and their decline with time, mineralogy and the need to handle more complex ores, disposal and minimising of wastes and the availability of water, power, skilled labour and the like together with increasing expectations from the community, concerns on sustainability and safety and, as well, climate change forcing a more targeted approach on energy. In this paper, the author builds on previous reviews to the IMPC and suggests that while step changes are long overdue, the unprecedented demand mitigates against drastic changes. That said, the ?Mine of the Future? is already requiring some different approaches.

Jan 1, 2014

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By L. S. Gertsch

The production of minerals for human use at locations other than the Earth is expected to ?advance ? human prosperity in ? ways that [do] not compromise the potential prosperity and quality of life of future generations? (Brundtland, 1987); in other words, sustainably. This paper examines the interaction of extra-terrestrial mineral production (ETMP) with the following sustainability imperatives: ? The sustainability of human activities on Earth; ? The sustainability of human activities elsewhere; ? Human survival in general, the ultimate sustainability goal. Some of the consequences of mineral production on Earth are widely considered to decrease the future prosperity and quality of human life. Examples include noxious by-products or wastes and unsettling economic up- and downswings. Moving mineral production activities to extra-terrestrial locations, where appropriate, will decrease many of its deleterious effects. Terrestrial mineral production presently is decreasing in some countries and increasing in others, moving from the cheaper and easier ores to more expensive, difficult materials. When the full costs of maintaining the terrestrial environment in a sustainable manner are included, total mineral pro-duction costs must increase. The cost of extracting mineral products from extra-terrestrial sources will be substantially higher, especially in the initial phases, but as the full costs of terrestrial production increase, at some point in the future (different points for different minerals), the curves will cross (Fig.1). This will occur at different points for different materials, a process whose prediction will be complicated by substitution of cheaper materials for some uses as prices of the original material rise. In summary, mineral products from extra-terrestrial sources will tend to increase the sustainability of human civilization, once steady state has been reached.

Jan 1, 2014

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018