Search Documents

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Y. G. Sun

This paper mainly reported separation manganese silver oxidized ores process by amylum de-gradation reduction and its influencing factors. When dosage is given according to nMn : nH2SO4 : n(C6H10O5)n : nH2O=1:k21.8: k116.66:30, the amount of up to 95.93% Mn leach rate and less than 2% silver loss can be obtained. Cyanidation process was used to extracted silver from leaching Mn residues. Silver leach rate could reach 94.15% at consumed amount of 1kg/t NaCN for 1h. Silver leach recovery rate was more than 92.27% by leaching Mn and cyanidation two-step processes so manganese and silver were separated effectively.

Jan 1, 2014

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018

By Q. Zhang

Phosphate tailings through Flotation contains large amount of dolomite which is difficult to be separated from apatite. In this present research, phosphate tailings is recycled by Flotation i.e. re-processing. High-purity dolomite with purity as high as 91.17% is seperated, which contains 19.82% of MgO. The results of orthogonal test show that the effect of various levels of different factors on the high-purity dolomite floatated. Future utilization of purified dolomite is also discussed: magnesium fertiliser especially magnesium phosphate is expected to be an ideal product from high-purity dolomite.

Jan 1, 2014

By O. Kökkilic

This study covers the tests to develop separation process for production of clay and colemanite rich concentrates, and aims to serve the clay and colemanite concentrates extracted from the tailing dams to the industrial applications. For this purpose, samples from the tailing dams in Kestelek Boron Plant (Turkey) with an average B2O3 content of 8%~11 % were subjected to the investigations. The separation process of hydrocyclone--to make clear the way to obtain either clean clay or cole-manite--was initially discussed. Therefore, following the gentle scrubbing (to keep the bimodal size distribution between clay and colemanite) of the tailings to disperse the slurry, two alternative multistage hydrocyclone processes; allowing to recycling the overflows or underflows to concentrate clay and colemanite were respectively tested. As a result of the preliminary tests, the multistage hydrocyclone separation in direction to the clean colemanite concentrates (recycling the underflows) gave the better separation efficiencies. So, all the parameters such as apex and vortex finder diameters and feeding pressures were examined with the multistage hydrocyclone process allowing the recycling the underflows. The detailed multistage hydrocyclone separation process of the tailing dam wastes yielded with colemanite concentrates (approx. 12 % of the feed, w/w) with B2O3 content of 35.0 % and the clay concentrates (approx. 42 % of the feed, w/w) with B2O3 content of 2.1 %. Colemanite concentrates were found good enough either to re-feed in to the separation process or to keep upgrading for final product ready to use in Industry whereas the attempts on production of light bricks from clay concentrates has failed. But it is worth to point out that these clay concentrates can be used for agricultural purposes just in the form as it is.

Jan 1, 2014

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By S. L. Zheng

The compound material of Nano-TiO2 Supported on the diatomite was prepared by the hydrolytic method with purified diatomite and TiCl4. The compound material was characterized by SEM, XRD, TEM, EDX, XPS, and the application test of the compound material was studied. The characterization test results showed that the Nano-TiO2 was coated on the surface of diatomite, the crystal of TiO2 is anatase, and the average crystal size is 12 nm. The pore diameter was reduced, but pore volume and surface area of the compound material are increased after Nano-TiO2 Supported on the diatomite. The application test results for treating coking waste water and formaldehyde gas show that the compound material of Nano-TiO2 / diatomite has adsorption and photo-catalytic function and strong degradation performance for phenol and formaldehyde.

Jan 1, 2014

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By L. X. Zeng

The low-grade nickel resource is very abundant in the western China. To make the best of the low grade nickel ore, we studied the process mineralogy and beneficiation process of nickel ore in the Yangliuping of Sichuan province. The grade of nickel is 0.45% in the nickel ore and the nickel exists in the sulfide including pyrrhotite, nickel pyrite, chalcopyrite primarily. The nickel distributes in pentlandite and magnetite over 90% and the copper does in the chalcopyrite over 95%. The carri-er minerals of useful elements tend to concentrate in space for concentration. As is shown in grain-size analysis of three major minerals, there are some more fine-grained grains with the percent of from 10% to 15% (<40 µm) and from 3.5% to 5.5% (<20 µm). So there will be some smaller size disseminated sulfide minerals difficulty to liberate in the process of concentration. The liberation degree of sulfide is not high and there are much associativity in the sulfides. Therefore, we should reclaim the sulfide aggregation dominating as pentlandite when concentrating. In addition, the sulphide minerals is so brittle that we should take care of preventing from crashing when grinding. The gangue mineral is mostly metamorphic mineral including serpentine, chlorite and amphibole which is easy to be argillization and difficult to concentrate.

Jan 1, 2014

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014

By Y. B. Zhu

Soil reconstruction and improvement trials and vegetation experiment is carried out at Shuilong-shan acid rock waste dumps at Dexing Copper Mine in China. pH value, Cu2+, Pb2+, Zn2+, etc. concentration in acid rock drainage (ARD) is also monitored every month since 2005. The results of experiment show that: Lime and topsoil stripped from open-pit is appropriated soil improvement material. Full cover soil improvement method is suitable for flat area, contour soil improvement method and hole soil improvement method is appropriate for slope area. The optimal plant species is ligustrum lucidum Ait,Lespedeza bicolor, Paspalum notatum, Veti-veria zizanioides, Eragrostis pilos and Neyraudia reynaudian. It is the best for Arbor, shrub and grass to be arranged in pairs or groups in order to remold optimal landscape. Pilot sites, covering 3ha, is established. Vegetation coverage reaches 90% in platform area, 40% in slope area. pH value in ARD increased slightly, Cu2+, Pb2+ concentration in ARD decreased, Zn2+ concentration in ARD decreased and varied slightly.

Jan 1, 2014