Search Documents

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1997

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By S. D. Zhang

The first reinforced earth railway bridge abutment in China has been successfully constructed of September, 1985 under the supervision of the Reinforced Earth Researth Group of Shanghai Institute of Railway Technology. In order to verify the reliability of the designed structure and its behaviuors, the 1:10 reduced scale model tests in laboratory and field tests on the actual structure during construction were proceeded. Various loads of different positions were charged, the vertical and lateral earth pressure in the filling soil, the stresses developed in the reinforcements, and the deformations of the models or the actual structure were recorded in those tests. The behaviors recorded are presented and discussed in this paper.

Jan 1, 2010

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By J. Tanner Blackburn, James R. Gingery, Lisheng Shao

Rigid inclusions consist of grout columns installed using displacement auger or vibrated tooling. The columns are typically installed in an array to provide support for footings, mats, or embankments. Due to the relative small column diameter and low replacement ratio, the surrounding soils typically have minimal densification or improvement. A gravel load transfer platform is commonly used above the rigid inclusion head to distribute stresses more broadly to the supported structure. The axial stiffness and geotechnical engineering mechanics of rigid inclusion design are similar to those of deep foundation systems, but they are typically only lightly- or un-reinforced and are not structurally connected to the above-grade structure. The popularity of rigid inclusions is increasing in the Western U.S., where many urban areas are subject to moderate to high seismic hazard levels. However, the performance of rigid inclusions under seismic loading is poorly understood, and seldom addressed in current designs. The elements are brittle, with limited or no ductility and relatively low moment capacity, and therefore may be prone to damage under seismic loading. Three modes of seismic loading should be considered: inertial loading from the structure, kinematic loading from vertically propagating shear waves, and kinematic loading from ground failure- related permanent ground deformation. This paper focuses on the first two modes. A simplified procedure for evaluating kinematic and inertial loading of rigid inclusions is described, and its use is illustrated through application to a site in Southern California. The results show that moderate to severe kinematic loading can generate plastic hinges in the rigid inclusions. Engineering consequences of this hinging could include settlement or bearing failure. INTRODUCTION In this paper the term ‘rigid inclusion’ (RI) refers to grout or grouted aggregate columns that are installed using either drilled or vibration displacement techniques. They are commonly installed in arrays to support vertical loads from footings, mats, or embankments. RIs are not structurally connected to footings they support. Rather, it is typical for a dense gravel load transfer platform (LTP) to be installed as a cushion between the RI head and supported footing or new fill. In cases of RI support of fill embankments, the LTP may be reinforced with horizontal layers of geogrid.

Jan 1, 2018

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By James A. Schneider

The successful installation of long piles driven into very dense sands relies on the occurrence of the reduction in local friction with increased pile embedment, a phenomenon known as ?friction fatigue?. The underlying mechanisms controlling friction fatigue are poorly understood, with some design methods including an adjustment for the influence of pile diameter while others do not. This paper back calculates the installation resistance of 0.356m to 2m (14in to 78in) diameter open ended piles driven into very dense sands using wave equation analyses. Cone penetration test data are used to link soil properties to installation resistance. The study illustrates consistent interpretation of a variety of case histories of open ended piles driven in very dense sands using newly developed analysis techniques and normalized parameters. Results provide information on methods for incorporating friction fatigue into drivability studies as well as a discussion of mechanisms related to pipe pile installation resistance in sandy soils.

Jan 1, 2010

By D. V. Roberts

Approximately 800 private consulting engineering firms in America specialize in geotechnical engineering. The gross income from these firms totals about $500 to $600 million per year. Sixty-five to seventy-five percent of this geotechnical work is per­formed by consulting engineers that belong to the Association of Soil and Foundation Engineers (ASFE). This paper presents statistics concerning the business activities and functions provided by ASFE member firms. The procedures used in typical projects are described. The paper concludes with a summary of major trends which are impacting the American geotechnical practice today.

Jan 1, 2010

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Brian Isherwood

TransCanada Pipelines, Calgary (TCPL) is one of North America's leading transporters of natural gas through its energy transmission business. TransCanada also operates significant complementary businesses in energy marketing and energy processing in North America and internationally. The main trunk pipeline crossing Canada comprises as many as six pipes, 30" to 48" diameter delivering up to 7.8 trillion cubic feet of natural gas per day. To maintain the maximum operating pressure of 1000 psi, it is necessary to provide compressor stations at 60 to 100 km spacing. One such station is located at Potter, in northern Ontario, some 80 km north of Timmins, referred to as Station 102. The station contains two compressor plants, 'A' and 'B' Each incorporates a gas turbine driven centrifugal compressor unit. 'A' Plant uses an aero-derived gas generator (jet engine) rated at 15 MW (19,000 HP).

Jan 1, 1997

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990