Search Documents

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By Euler De Souza

Backfilling in Canadian mines has been practised for close to 100 years and evidence anticipates the application of mine fill technology at an increasing rate during the foreseeable future. The evolution of backfill technology is closely related to the advancement of modern mining methods and the development of new backfill technology continues to evolve. The authors, after conducting extensive surveys of backfill practices in underground mines across Canada, have concluded that, because backfill operations employ large quantities of cement and experience large costs associated both with backfilling practice and cement use, opportunities exist for reducing backfill energy costs and enhancing the application of alternative cementing agents in backfill. Consequently, the authors have developed an alternate, equally effective and lower cost binder agent replacement for cement, and incorporated waste glass into the development of a lower cost backfill (glassfill). This paper presents the results of two design stages associated with the development of glassfill: strength development and flow performance. The advancement of this technology has reached a stage that should promote industrial implementation within the Canadian mining industry. A number of Canadian mining operations exhibit potential for plant optimization through possible binder source replacement, and might thus realize associated reductions in backfill and energy costs.

Apr 1, 2005

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By T. Belem

The main objective of this study is to better understand the effect of underground CPB placement conditions on its microstructural, hydro-mechanical and geochemical properties. To reach this objective, three PVC columns, each 3 m high, were built, and were filled with CPB material. The columns allow simulating undrained (UD), half-drained (HD) and fully-drained (FD) conditions along with the measurement of resulting self-weight consolidation settlement of the CPB. Bleed and drainage waters were also collected from each column for geochemical analyses (pH, Eh, EC, SO42- content). After 90-days of curing time, a total of sixty CPB samples were cored from the backfill columns and subjected to uniaxial compression tests followed by physical characterization (Gs, void ratio, water content, degree of saturation, specific surface area). The results showed that the total drainage water and the maximum observed settlement occur mainly within the first 72 hours after the columns are filled. The corresponding volumetric strains suggest that in situ backfilled stopes simulated behave in a similar way to the fully-drained (FD) or the half-drained (HD) conditions. The MIP test results show that the pore structure varies between the top and the bottom of each column.

May 1, 2007

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By Sune Eriksson, Stig Peterssonsune, Christer Fridfeldt

"Boliden Metal Corporation has developed a technique to treat complex copper concentrates containing large amounts of lead, zinc, arsenic, antimony and bismuth which cannot be treated in conventional smelters due to the impurities.Tests were carried out to treat such complex copper concentrates in the TBRC. They were performed in a pilot-plant TBRC with charges of 5 tons. These tests resulted in a new method to treat complex copper raw materials and produce a blister copper low in impurities. The background and data from the test work are presented as well as a flowsheet for a full-scale process.IntroductionThe Ronnskar Works is situated on the coast of the Gulf of Bothnia, 40 miles east of the Boliden Mine. Smelting began at Ronnskar in 1930 to process the complex ore extracted from the Boliden Mine. The Ronnskar Works has subsequently developed into a relatively integrated smelting plant.Copper and lead sulphide concentrates from Boliden's own mines as well as purchased copper raw materials are processed. The main products are refined copper and lead, but full utilization of the raw material also yields other metals and some metallurgical and chemical by-products. The products include gold, silver, zinc clinker, white arsenic, arsenic salts and arsenic metal , selenium and selenium compounds, nickel sulphates, sulphuric acid and liquid sulphur dioxide."

Jan 1, 1981

By Fernando Romero Lage

The purpose of this paper is to analyze detailed crushing and screening configurations and the interrelationship as they relate to mass flow balance, operating efficiency, plant availability and final production. The entropy of ore bodies limits the standardization of crushing and screening plants, however, consideration for a continuous and sensible assessment of the mass flow balance of the circuit will yield the best achievable results. Since energy costs have continuously risen in the last few years, it is imperative that these circuits offer low power requirements and low operating expenses. The paper will detail how the efficient implementation of continuous mass flow balance in the application of crushing and screening plants will generate quality improvement and process improvement, which will translate into bigger production and energy savings.

May 1, 2010

"This paper reviews the chemistry involved in the recovery of gold from cyanide solution with anion-exchange resins, and also discusses the most critical aspects of the engineering of an effective resin-in-pulp (RIP) process. As far as the chemistry is concerned, the conclusions reached by a great many researchers, as well as the performance of the only operating RIP plant in the Western World, at the Golden Jubilee Mine in South Africa, support the view that the process is technically viable and, in many cases, could prove to be more attractive economically than alternative processes such as zinc cementation and carbon-in-pulp (CIP). On the engineering side, there is still a need for further development before larger scale ( > 50,000 tpm) RIP plants can be designed, built and operated with confidence. However, the experiences gained during nearly 3 years of operation of the Golden Jublee RIP plant indicate that the process can be engineered with confidence for smaller operations ( < 50,000 tpm), and this will probably be the scope of application of the first-generation RIP plants. INTRODUCTIONThe use of anion-exchange resins in gold processing has, for a number of years, been proposed as an alternative to more conventional processes such as zinc cementation and carbon adsorption, and detailed research programs that have been carried out at a number of laboratories have demonstrated the technical viability of the process. (Burstall et al, 1953, Davison et al., 1960, Tataru, 1973, Laskorin et al. 1978, Hosking, 1984, Riveros and Cooper, 1987 and Palmer et al., 1988)The main incentive for this work was the fact that resins have several characteristics that are quite different from carbon, which make them potentially more attractive substrates for the recovery of gold. The following are examples: -"

Jan 1, 1991

By Jesse L. Duke

Outline ?Understanding the context ?The Business, political, social and legal environment ?Recipes for Success (three Ps) ?Develop effective Partnerships/relationships ?Plan carefully ?Actively Manage the ?Process? Business Environment ?Nunavut?Impressive mineral potential ?Emerging diamond industry ?Dominated by Juniors ?NWT ?Maturing Diamond industry ?Emerging oil and gas industry ?Yukon ?Alaska Highway Pipeline ?Junior-dominated exploration and development ?Growing acknowledgement in Canada of the importance of northern resources ?Shift of thinking: north-south infrastructure (vs. East-west)

May 1, 2006

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009